Receiver FTP Error

Hi Experts
In the receiver file adapter we are getting the following error while writing the file to FTP:
Message processing failed. Cause: com.sap.engine.interfaces.messaging.api.exception.MessagingException: An error occurred while connecting to the FTP server XX.XXX.XX.X:21'. The FTP server returned the following error message: 'com.sap.aii.adapter.file.ftp.FTPEx: 550 /Myfolder/Inbound: The system cannot find the path specified. '. For details, contact your FTP server vendor.
refered forum post on this but no luck.
We have verified the following :
1.Tried connectiong to specified FTP from PI server, the connection is happening and were able to place a file using PUT
command .
2. The Channel configuration is also fine ,user credentials are mentioned correctly .
3. We tried changing the directory to a local FTP and file operation is successful.
4.Made dummy changes in channel config , saved activated. Also tried stopigng/restarting channel in RWB.
Is there any specific PI user access required to be checked/enabled by cleint FTP team?
Still we have the same error .
Regards,
Srinivas

Hi,
1. Do you use the Central Adapter Engine or a decentralized one ? if yes, to do your test, you have to connect you on the decentralised AE and not on PI.
2. To be sure to clean entirely the cache, you have go in Visual Admin (Pi7.0) and stop-start the service "FILE adapter".
Link is: Tab Cluster -> Server > Services > SAP XI Adapter: File.
3. Do not forget also, that in RWB > Cache Monitoring, you can see the content cache of a specific CC (for instance).
I Hope it will help you.
Regards.
Mickael
Edited by: Mickael Huchet on Oct 5, 2010 8:10 AM

Similar Messages

FTP error: Receiver Communication Channel

Hello Experts,
I am getting the following FTP error in my Receiver Communication Channel.
Error occurred while connecting to FTP server: Peer certificate rejected by ChainVerifier
Please suggest.
Thanks,
Anup

Hi Anup,
Problem is with FTPS and not FTP.The SSL handshake needs to confirm that the FTPS client is using the FTPS server's DNS name to access the FTP service since only the DNS name of the FTPS server is stored in the certificate signed by the trusted CA (e.g. VeriSign). it's the way the Certification Authorities works.
If you are using any IP address then try with your host name.
Regards,
Madan

I received an error message after trying to update Firefox and can no longer access Firefox. What do I do?

I received a notice to update Firefox, so I did. During installation, I received an error message stating "The procedure entry point GetLogicalProcessorInformation could not be located in the dynamic link and can no longer get into firefox at all. What do I do? I even uninstalled it, restarted my computer, and tried reinstalling it, and it still won't work. I'm also receiving a message that firefox.exe has encountered a problem. Please let me know how to proceed. Thank you.

hi again, mozilla has just released an update to firefox 36.0.1 which should address the problem: ftp://ftp.mozilla.org/pub/mozilla.org/firefox/releases/36.0.1/win32/

How can get Dreamweaver to stop error message: an ftp error has occurred- cannot connect to host?

Dreamweaver is locking me out when I try to connect to the host via ftp. I get the error message: "An ftp error has occurred - cannot make connection to host". This error message started yesterday when I used the wrong host ftp address too many times. I have since received the correct ftp address from my website host, but the system won't even let me log in...it just gives me that error message when I click the connection button on the panel. My website host recommends that I uninstall Dreamweaver and re-install it again. My concern is, if I un-install the Dreamweaver app, which I downloaded from the Cloud, will the Cloud know I've un-installed Dreamweaver and allow me to download it again? Please help.

See my response in your most recent thread. Please don't double post like that - it can confuse things considerably when replies come in to both threads.

Empty files are getting created at receiver FTP server

Hi Experts,
I have an Idoc to File scenario where I am sending an XML file to receiver FTP server.
Scenario is working fine but sometimes an empty file is getting generated at receiver FTP server.
I have already selected ignore empty file at receiver channel so issue is not within PI system configuration.
When I checked the message log I can see that almost all the files are getting created successfully without any issues, but
for some files/messages I can see that there are below error logs.
"Transmitting the message to endpoint <local> using connection IDoc_AAE_http://sap.com/xi/XI/System failed, due to: com.sap.engine.interfaces.messaging.api.exception.MessagingException: Could not get FTP connection from connection pool (1 connections) within 5,000 milliseconds; increase the number of available connections"
"Exception caught by adapter framework: Could not get FTP connection from connection pool (1 connections) within 5,000 milliseconds; increase the number of available connections."
And after there is again success message log in the same message and it creating a file successfully during that time stamp.
but the third party is sometime receiving empty file which I am not able to find in any trace or log (my file name is SD_timestamp.xml).
Can you please let me know what is the solution and what adjustments FTP server need to do in order to resolve this issue.
Thanks in advance.
Regards,
Rahul Kulkarni

The error you are getting that says "Could not get FTP connection from connection pool (1 connections) within 5,000 milliseconds; increase the number of available connections" has probably nothing to do with the empty files problem.
I second Hareesh Gampa that you first should try "temporary file creation". You might also need to tell the FTP owner that he should only pick up files with that are written completely and that do comply with a negotiated file name schema. The temp file should have another schema of course then. He should not pick up just every file that is written. See here for details
http://help.sap.de/saphelp_nw74/helpdata/en/44/6830e67f2a6d12e10000000a1553f6/content.htm
HTH
Cheers
Jens

Q? Receiver determination error ????

Hi all.
I wana transfer from R3 IDOC to XML with FTP service.
Although I think configuration completely was finished, happens error.
How can i correct?
It's results from test configuration.
    Receiver Determination <Not found>
       Internal Error
       HTTP connection to ABAP Runtime failed.
       Error: 403 Forbidden
       URL: http://R3:8000/sap/xi/simulation?sap-client=
       User: XIDIRUSER Check
=======================================================
Scenario : R3 IDOC -> FTP XML (import Ext Definition DTD)
1) create Business Service System     : R3, FTP
2) create Message Interface about FTP : MI_FTP_in
3) create Interface Mapping R3 & FTP : IM_R3_to_FTP
4) import business system about FTP server : FTP
5) create Receiver Determination : |R3|IDOC_inf
     sender : R3
           - interface : IDOC interface
     configured Receivers
           - Service   : FTP
           - Receiver : FTP
           - interface : MI_FTP_in
           - Mapping   : IM_R3_to_FTP
           - Receiver Agreement: FTP_file_adapter
6) create Interface Determination: |R3|IDOC_inf||FTP
     Sender   : R3
           - interface : IDOC interface
     receiver : FTP
     Configured Inbound Interface
           - Inbound interface : MI_FTP_in
           - interface Mapping : IM_R3_to_FTP
7) create Receiver Agreement : |R3|IDOC_inf|MI_FTP_in
     Sender   : R3
     Receiver : FTP
           - interface : MI_FTP_in
           - Receiver Channel : FTP_File_Adapter
========================================================

Hi,
Please can you check you Cache is updated or not.If cache is succesfull then check the Port & RFC Destination and Partner profiles R/3 side and XI side.
R u testing this scenario using WE19.
If using we 19 then check the your sender information and receiver information (I mean to say Port,Parner...with outbound parameters )
Regards,
Venu.

FTP Error - 550 Unexpected reply code

Hi Guys,
I am encountering the following error in my QA Environment.
Error Attempt to process file failed with com.sap.aii.adapter.file.ftp.FTPEx: 550 Unexpected reply codeThe filename, directory name, or volume label syntax is incorrect.
In my receiver FTP channel, I have set the 'Temporary File Name Scheme' as '*.tmp'. I have the same setup in my Dev environment but no issue is encountered.
When I tried to removed it, the error is not occurring.
What do you think could be the issue?
Also, what should be the File Type if the temp file name scheme is *.tmp? Binary or Text?
Message Flow: IDOC -> File
Thanks and Regards,
Neil

A file name should not contain "* "
when you define the tempfilename scheme as "*.tmp" , PI is trying to create the file as *<timestamp>.tmp to place the file on FTP which is not allowed.
refer : Configuring the Receiver File Adapter - Configuring the File/FTP Adapter in Integration Directory/PCK - SAP Library
>>>Also, what should be the File Type if the temp file name scheme is *.tmp? Binary or Text?
It can be anything.

Why do I keep receiving the error message: disk failed image corrupt

I am trying to upgrade my version of Firefox from 2.0.0.2 (downloaded Nov. 2007) to the new version 3.6.12. on my IMac desktop computer.
When I download the file I receive a white and grey icon that says Firefox 3.6.12.dmg. When I click on this icon I receive the error message:
mounting disk failed; image corrupt.

Firefox 3.0 and 3.5/6 versions require at least Mac OS X 10.4
*http://www.mozilla.com/en-US/firefox/system-requirements.html - Mozilla Firefox 3.6 System Requirements
Firefox 2.0.0.20 is the last release that runs on Mac OS X 10.2 and 10.3
See:
* http://kb.mozillazine.org/Installing_Firefox
* http://kb.mozillazine.org/Unsupported_operating_systems
Mac: https://ftp.mozilla.org/pub/mozilla.org/firefox/releases/2.0.0.20/mac/en-US/
If you have Mac OS X 10.4 or newer then do this:
* Download a new copy of the Firefox program: http://www.mozilla.com/firefox/all.html
* Trash the current Firefox application to do a clean (re)install.
* Install the new version that you have downloaded.
Your profile data is stored elsewhere in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder], so you won't lose your bookmarks and other personal data.
Other things that need attention.<br>
Your above posted system details show two old Flash 9 plugins that you should remove and update to the latest Flash 9 version.
text
# Shockwave Flash 9.0 r47
# Shockwave Flash 9.0 r16
Flash Player 9: http://www.adobe.com/go/kb406791 (Flash Player 9 for Unsupported Operating Systems)

Packer FTP errors when trying to update

I've been getting the following errors for several weeks now when trying to update my AUR packages:
Aur Targets (3): gdk-pixbuf glib gtk
Proceed with installation? [Y/n]
Edit gdk-pixbuf PKGBUILD with $EDITOR? [Y/n] n
==> Making package: gdk-pixbuf 0.22.0-12 (Thu Jul 10 18:29:05 PDT 2014)
==> Checking runtime dependencies...
==> Checking buildtime dependencies...
==> Retrieving sources...
-> Downloading gdk-pixbuf-0.22.0.tar.bz2...
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
0 388k 0 0 0 0 0 0 --:--:-- 0:00:05 --:--:-- 0
Warning: Transient problem: FTP error Will retry in 3 seconds. 3 retries left.
0 388k 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
Warning: Transient problem: FTP error Will retry in 3 seconds. 2 retries left.
0 388k 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
Warning: Transient problem: FTP error Will retry in 3 seconds. 1 retries left.
0 388k 0 0 0 0 0 0 --:--:-- --:--:-- --:--:-- 0
curl: (19) RETR response: 425
==> ERROR: Failure while downloading gdk-pixbuf-0.22.0.tar.bz2
Aborting...
The build failed.
I've tried changing curl to wget in the /etc/makepkg.conf file--but it still fails (error messages are different).
My connection is fine for everything else, so I'm stumped!

Try using just makepkg. Works for me.

Endpoint shutdown (FTP) on web exception. FTP error 421

Hi,
When using FTP Source in my Biztalk Services project it sometimes occurs that we receive an error 421 from the FTP server. This causes the endpoint to shutdown, which will result in a manual action to restart the endpoint again.
We're looking into the cause of the 421 error, but the strange thing is that 4 bridges within the same project use the same FTP server, but they do not all shutdown. This makes it assumable that it's a short hickup in the system.
Is there a way to set a strategy of backoff and retrying instead of shutting down the endpoint for FTP errors ? I my opinion, /I shouldn't need to rely on a 3rd party to keep my infrastructure running.

The bridge will shut down after retry attempts at delayed polling intervals.
You may want to monitor Operation Logs / Event logs for such events.
You may write a simple PS script which can run periodically to start the bridges and make sure that the bridges are in started state.
http://msdn.microsoft.com/en-us/library/azure/dn232351.aspx
regards,
Shailesh Agre

Dreamweaver - FTP Error

Hello,
I am a creative cloud subscriber and therefore host through Adobe's Business Catalyst. I have had no issues for months with my site. However, as I went to go update and "put" my site. I got this error message:
"an ftp error occurred - cannot make connection to host. Your login or password is incorrect. Please check your connection information."
I have not messed with any settings within dreamweaver. The only thing I can think of, is I added a MX record to send and receive emails through a domain email address.
Can anyone please help?
This is quite urgent!
Thank you in advance

Hi jonlehman,
Which version of Dreamweaver are you using? You can get this information by going to menu:
MAC - "Dreamweaver -> About Dreamweaver"
WIN - "Help -> About Dreamweaver"
Also, please provide your platform and OS information.
Thanks,
Arindam

Remote host ftp error dw8 and Mac OS X using airport

I'm learning PHP at a local tech school and can put files and
can connect to my SQL database at the school using DW CS3 and Win
XP. I have a wired connection at school. However, when I try to
work on my site at home on my Mac using OS X 10.4.11 and DW8 I
receive the error: "An FTP error occurred cannot make connection to
host. The remote host cannot be found.
I'm am using passive ftp in dw8 and in my network preferences
on my Mac. I've double checked my settings for the site definition
and cannot find anything wrong. I'm using the same site definition
at school and at home. Since I can connect at school I think it may
be a problem with my firewall and airport. FTP on port 21 is
allowed under firewall preferences.
Any thoughts would be greatly appreciated. I am thoroughly
confused!

If you home is not on the same network as your school I'm
surprised you can
connect via Transmit because 10.4.11 is not a valid IP
address. Addresses
starting in the 10.0.0.0 -> 10.255.255.255 range are in a
reserved block
http://www.pantz.org/software/tcpip/subnetchart.html
Cheryl D Wise
"budd100276" <[email protected]> wrote in
message
news:fjv3fd$b9k$[email protected]..
>I forgot to add that I can connect to the server using
another ftp client -
>Transmit.
>
> Thanks.

FTP Error Occurred

When I Try to connect to to the FTP
i am able to connect to my other website but not the newest
one i bought...
An ftp error occurred - cannot make connection to host. no
response from the server. this may be due to one or more of the
following reasons:
- accessing the server requires firewall settings that aren't
properly set. please verify that the firewall setting in the site
category of the preferences dialogue box are properly set, and that
the use firewall option in the site definition dialog box is
selected.
- the server may be accepting only passive mode or only
active mode. toggling the "use passive FTP" check box may help you
establish a connection.
- if you are connection to an IPv6 enabled server, please
select "use IPv6 transfer mode" check box in the advanced site
definition dialog.
- your local firewall may be blocking the incoming FTP data.
please disable it to see if it makes a difference.
- It is possible your FTP may be using a non-standard FTP
port(21). if you need to specify a non - standard port, enter the
port number after the host name separated by a colon":"
I don't know why i receive this message all the time but i
need help resolving this issue..

iSaluk posted in macromedia.dreamweaver
> How long should it take for me to be able to connect
cause i
> bought it a while ago like 1-2 days ago..?
The typical disclaimer is up to 48 hours. Can you connect
with the IP
address?
You might try turning on/off Passive Mode in the site
definition.
Are you certain you have the correct user id and password for
the new
site? You can test this with your OS built-in FTP client.
Open a command line interface (Windows: cmd, OS X: terminal)
and type
the following, using your domain name, user id, and password
at the
appropriate prompts:
ftp ftp.example.com
user
password
ls
bye
Were you able to log in and see a list of files/directories?
Mark A. Boyd
Keep-On-Learnin' :)

FTP Error Occurred - Cannot make connection

I've been receiving this message:
"An ftp error occurred - cannot make connection to host. Your
login or password is incorrect. Please check your connection
information."
when trying to set-up and download active websites originally
built in FrontPage. Do Dreamweaver & FrontPage not play well
with each other? Why would that affect my being able to connect to
my websites via Dreamweaver? I have double and triple checked the
logins and passwords. They are correct. Also, I have no problem
setting up and uploading a new site.
Remote Info Site Definition Settings:
Access: FTP
FTP host: www.mywebsite.com
Host directory: blank
Login: my login
Password: my password
I've:
tried with passive FTP checked and unchecked
tried with Secure FTP checked and unchecked
Unchecked FTP performance Optimization in Server
Compatibility
Thanks to anyone who can help :)

No. My sites that I created originally in Dreamweaver work
and connect fine. I've compared the settings and I have them set
the same. It's driving me nuts, to say the least!!

Webfusion host & FTP error

My problem:
I'm trying to launch my first ever website, created in DreamWeaver, via DreamWeaver's FTP onto my Webfusion shared server linux host account. I am unable to connect to Webfusion's server. I do not know whether the problem lies:
with me putting in the information incorrectly into the Site Definition boxes, or
(as Webfusion suggest) a DreamWeaver problem or
a Webfusion problem.
I would appreciate help from any other member who uses both DreamWeaver and Webfusion regarding how to input my information in the Site Definition boxes and how to get connected.
What I've tried to do:
I've followed the advice in my "Adobe DreamWeaver CS4 Classroom in a Book" where it (not very well) explains how to set up a remote FTP site and I've got an error message: "An FTP error occured - cannot make connection to host. The remote host cannot be found". Trying to connect to the host server (using the Test button) is also causing a problem in my personal configuration folder, which I've managed to sort out using David Powers' post dated June 4 2002 http://forums.adobe.com/thread/417116?tstart=0#cache'.
I've searched Webfusion's support site for help in completing the boxes in DreamWeaver's Remote info section of the Site Definition box, but their article seem to contradict Adobe's advice. I've also spoken to Webfusion's help desk. The guy I spoke to gave me some help (as he used DreamWeaver himself) but he told me that he shouldn't help me on this problem as the company did not help on third party software problems. He did reset my password as he thought that that could be a problem. The reset has not helped.
Details:
I'm hesitating over putting the information I have in my Remote info boxes in this post as I don't really understand (with the exception of the username and password) how much of the information is personal to me and therefore shouldn't be posted here.
Any help would be gratefully received as I am really stuck.
Gill

Hi Ricky
Thanks for your reponse.
Since I posted my query I've tried using Webfusion's online file manager (per Webfusion's help article) but was not able to upload my files.
I've also tried to connect again via DreamWeaver using your post below, although I am not sure what to put into the Login name box. Your post says: [email protected], but my username is longer than just the domain name (is this because my domain name is not via Webfusion/123-reg, but another domain name provider?). It is in the following form: [email protected] Does this mean that in the Login box I should enter:
ftp@[email protected], or
[email protected]
I've tried both of the above and also the following:
[email protected]
[email protected]
together with the other information in your post. I've left the 'Use passive FTP' box checked (as per your colleague on the help desk) and I've unchecked the 'Use FTP performance optimization' box in the Server Compatibility box (as per DreamWeaver's suggestion when experiencing problems). I've left in and then taken out the Host Directory: public_html. I've still no joy via DreamWeaver.
Current position:
Today I've used FireFTP and (finally) managed to connect to the server. My files are now on the Webfusion server, but I can only view the site if I use the address given to '..view your content whilst your domain is configured at..' in my confirmation email. I get a 'Problem loading page' message if I search for my website via my domain name. I would be grateful if you could explain what I do next to sort this out.
I would also prefer to use DreamWeaver's FTP so any further help you can give on the login name box and why it's still not working for me would be appreciated.
Many thanks
Gill

Receiver FTP Error

Similar Messages

Maybe you are looking for