Call Manager register fxs port with voice gateway- problem

I have a CUCM 6 and a Voice Gateway V224. I've configured the voice gateway's voice FXS ports as MGCP.
I have a Voip connected and registered to the CUCM and a Pots phone connected to the Voice Gateway.
If i dial from the Voip to the Pots phone it rings. The problem is that i cannot ring from the Pots to the Voip phone.
I have no dial tone.
If i write no shut down on the  voice port i have a tone. If i configure mgcp on the voice port i have a busy ringtone.
I've entered no mgcp and mgcp commands and i've reset the voice gateway.
How can i call from the pots to the voip phone?
The ios version on the voice gateway is Version 12.4(22)T4.
Here is an outghtput from the Voice gateway.
ccm-manager mgcp
ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server 10.1.1.33
ccm-manager config
mgcp
mgcp call-agent CCMIOSS 2427 service-type mgcp version 0.1
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp package-capability rtp-package
mgcp package-capability sst-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp validate domain-name
mgcp rtp payload-type g726r16 static
mgcp profile default
timeout tone busy 600
timeout tone dial 600
dial-peer voice 999223 pots
service mgcpapp
port 2/23
dial-peer voice 999222 pots
service mgcpapp
port 2/22
dial-peer voice 999888 pots
service mgcpapp
port 2/23
The CUCM 6 is registered with the voice gateway.

Is your campaign using CPA? If so, what's the behavior if CPA is not enabled? 
I think the best thing to do is to run a trace...
Call Manager > Cisco Unified Serviceability > Trace > Configurations
Select a CUCM server - any subscriber would work. 
Service Group - CM Services
Cisco CallManager (Inactive)
Enable SIP Stack Trace and apply to all nodes. Download and install RTMT
Make a bunch of outbound tests and then open RTMT > Trace & Log Central > Collect Files > Check "All Servers" for Cisco CallManager > Next > Next > Relative Range if you made the test calls within the last X minutes, otherwise you can set a From and To datetime. Click Finish and go through your SDL logs and see what errors you find and post them here. 
Also, make sure your phone is in the correct CSS in Call Manager

Similar Messages

  • What versions of Call Manager support the new VG3XX Voice Gateways?

    What versions of Call Manager support the new VG3XX Voice Gateways?

    http://www.cisco.com/c/en/us/td/docs/routers/access/vg350/software/configuration/guide/vg350_scg/scgapp_platforms_ORIG.html#64565

  • Call Manager Express B-ACD with Call Manager 5 or 6

    Can I use the Call Manager Express B-ACD with Call Manager 5 or 6, because there is no autoattendant in CCM 5 or CCM 6

    Hi Zohaib,
    With CCM (all versions), they do ship with a "stripped down" version of IPCC/CRA which is where the actual AA is built. But this is not really an "on box" solution :( You will need a seperate MCS box to install IPCC on and then integrate with CCM via jtapi. Here is a clip and link for CCM 5.x and a link for 6.x which is a rather large PDF which I am having trouble downloading today;
    Cisco CallManager AutoAttendant
    Cisco CallManager AutoAttendant, a simple automated attendant, allows callers to locate people in your organization without talking to a receptionist. You can customize the prompts that are played for the caller, but you cannot customize how the software interacts with the customer.
    Cisco CallManager AutoAttendant comes bundled with Cisco CallManager on the Cisco CallManager 5 agent IPCC Express bundle.
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a0080531888.html#wp1026233
    Check out the 6.1 Features and Services Guide here;
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/prod_maintenance_guides_list.html
    Hope this helps!
    Rob

  • Adding MGCP FXS Ports to H323 Gateways

    Currently all of our Gateways are H.323 gateways.  Due to a business requirement we are now going to be enforcing our users to use forced authorization codes to place LD calls.  In order to facilitate this on our analog phones it seems the only option is to use MGCP gateways.
    From what I understand we can run multiple signalling protocols on voice gateways.  We have a variety of gateway models but by and large most of these gateways are VG224 models.  I think what I would like to do is keep the current h.323 dial-peer and voice-port settings for the PLAR emergency phones that we have on these gateways and only change the analog phones to MGCP. 
    Most of the route patterns to these h323 gateways look like this... 102[0-5] and then the dial peers on the individual gateways route to the appropriate voice port like this...
    dial-peer voice 1020 pots
     huntstop
     destination-pattern 1002
     port 2/21
    The Voice port config looks like this...
    voice-port 2/21
     timeouts interdigit 7
     description tie pr 1520
     station-id name PTRM 1020
     station-id number 1020
     caller-id enable
    My plan is to create the MGCP Gateways in CUCM as wells as the DN's... in this example x1020.  I will then enable MGCP on the gateways.  After that my assumption is that I can individually remove the Voice-port and dial-peer configurations and then add the MGCP dial peers with the port and "service MGCPAPP" commands.
    My other option is to redo the entire gateway at the same time and schedule after-hours down-times to make the change.  I want to avoid this if possible as we have 40+ gateways that need to be changed.
    Basically I just need some guidance or confirmation if my plan will work or if there is a better way to do this?  Are there any caveats or known issues I should look out for when running multiple signalling protocols on the same gateway?
    Thanks,
    Trav Moore

    Thanks Aaron,
    I was wondering about the MGCP ccm-config command but was worried it would re-write the entire h.323 gateway to MGCP.  Good to know that it won't and that this is a potential option.
    I actually do prefer the idea of only having one signalling protocol (I would like to go all SIP if not for the FAC codes needed). Unfortunately any maintenance that I do that impacts end-users requires a lot of after-hours scheduling and maintenance alerts.  These gateways have a combination of fax-machines, PLAR's (emergency phones and overhead paging), and analog phones.  Maybe eventually I can migrate all of these ports to MGCP.  For now the analog phones are the only ones that must be converted and if I can quickly convert them without anyone noticing aside from the minimal reset in CUCM then this would be ideal.
    Thanks!

  • Cisco Call Manager 5.1 and Cisco VoIP Gateways

    Hi,
    I have Cisco Call Manager 5.1 with Cisco 2800 series routers as a ISDN gateways and Cisco VG224/ATA 186 as POTS gateways. While Cisco Call Manager collects call statistics from 7900 series SCCP handsets managed by the Call Manager (number of VoIP packets, dropped frames etc.), it shows only one side of the call as it does not collect statistics from the Cisco routers (configured as H.323 gateways), the Cisco VG224 (with ports configured as H.323 gateways and as a SCCP devices) and Cisco ATA 186 (configured for SCCP).
    Is the collection of these statistics possible? What needs to be done?
    Thanks,
    Paul

    Update: Logging of QoS/Call Management Records (CMR) to Call Manager CDR database is not possible with H.323 gateways; only MGCP gateways:
    http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_qanda_item09186a008020650a.shtml#qa4
    Anyone know how to get the Cisco router gateway to log these statistics anyway using standard router logging mechanisms (e.g. syslog)?
    Anyone know about calls to SCCP ports on Cisco VG224 or ATA 186?
    Thanks,
    Paul

  • Call Manager 10.5 Compatibility with TelePresence

    Hi,
    We are in the process of upgrading CUCM to version 10.5.  Can someone please tell me the minimum versions of the following devices that are compatible with CUCM 10.5?
    VCS
    MCU 5320
    C40/90
    I am not able to locate this information on http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/compat/matrix/10_x/CUCM_BK_CD1DB914_00_compat_matrix.pdf. Is there another place that I should be looking?  Surely this is documented somewhere.
    Thanks,
    Scott

    Duplicate
    https://supportforums.cisco.com/discussion/12338356/call-manager-105-compatibility-matrix

  • Standby PRI not working with voice Gateway Router & CUCM

    Hi ALL ,            
    GOOD Day all of you .
    I am facing a big problem i.e  standby PRI not working with VG & CUCM , I have checked all the configuration parameter on VG & CUCM found ok but I am unable to make any call from standby link also incoming not come on the standby link . When I make a call on my Pilot no but getting busy tone .
    I observer the some errors on VG like Cause i = 0x8286 - Channel unacceptable on my second PRI channel .
    Please help me to reslove this proem .
    Following are the PRI configuration Parameter on CUCM .
    Product Specific Configuration Layout
    Line Coding  : HDB3
    Framing  : NON CRC4
    Clock  : External
    Input Gain (-6..14 db)  0
    Output Attenuation (-6..14 db)  0
    Echo Cancellation Enable 
    Echo Cancellation Coverage (ms)  64
    PRI configuration on VG
    interface Serial0/0/1:15
    encapsulation hdlc
    isdn switch-type primary-net5
    isdn incoming-voice voice
    isdn bind-l3 ccm-manager
    BR,
    SANDIPAN

    Hi Craig ,
    Thanks for your reply .
    We are using the full 30 channel E1 PRI .
    following are PRI Channel Statistics: 
    %Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 1. Layer 3 output may not apply
    ISDN Se0/0/0:15, Channel [1-31]
      Configured Isdn Interface (dsl) 1
       Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
        Channel :  1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
        State   :  0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
       Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
        Channel :  1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
        State   :  0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
    Please find following debug error
    VG_RO_01#isdn test call interface serial 0/0/0:15 09665484798
    Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User RX <- RRp sapi=0 tei=0 nr=5
    Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRp sapi=0 tei=0 nr=4
    Mar 7 03:00:54.570: ISDN Se0/0/0:15 Q921: User TX -> RRf sapi=0 tei=0 nr=4
    Mar 7 03:00:54.574: ISDN Se0/0/0:15 Q921: User RX <- RRf sapi=0 tei=0 nr=5
    CCIL_PUNE_DR_VG_RO_01#
    Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 09665484798
    Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=4
    Mar 7 03:00:55.994: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
    Bearer Capability i = 0x8890
    Standard = CCITT
    Transfer Capability = Unrestricted Digital
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA9839F
    Exclusive, Channel 31
    Called Party Number i = 0x81, '09665484798'
    Plan:ISDN, Type:Unknown
    Mar 7 03:00:56.006: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=6
    Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=4 nr=6
    Mar 7 03:00:56.018: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
    Cause i = 0x8286 - Channel unacceptable
    Mar 7 03:00:56.022: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=5
    Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=6 nr=5
    Mar 7 03:00:59.995: ISDN Se0/0/0:15 Q931: SETUP pd = 8 callref = 0x0084
    Bearer Capability i = 0x8890
    Standard = CCITT
    Transfer Capability = Unrestricted Digital
    Transfer Mode = Circuit
    Transfer Rate = 64 kbit/s
    Channel ID i = 0xA9839F
    Exclusive, Channel 31
    Called Party Number i = 0x81, '09665484798'
    Plan:ISDN, Type:Unknown
    Mar 7 03:01:00.007: ISDN Se0/0/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=7
    Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=5 nr=7
    Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x8084
    Cause i = 0x8286 - Channel unacceptable
    Mar 7 03:01:00.019: ISDN Se0/0/0:15 Q921: User TX -> RR sapi=0 tei=0 nr=6
    Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=7 nr=6
    Mar 7 03:01:03.995: ISDN Se0/0/0:15 Q931: RELEASE_COMP pd = 8 callref = 0x0084
    Cause i = 0x80E6 - Recovery on timer expiry
    Mar 7 03:01:03.995: ISDN Se0/0/0:15 **ERROR**: CCPCC_CallOrigination: SETUP timed-out (2nd T303) to NETWORK. The SETUP failed.
    BR ,
    SANDIPAN

  • Call park using fxs port on spa9000

    I have seen this question asked several times but no seems have answered it.
    Is it possible to enter a service code to park a call using an analogue phone. If it is, please share what is the service code and the procedure.
    I have a spa9000 with pstn (spa3002, spa400) and exts spa-942,xlite and spa2102/pap2. Everything works fine on the 942 phones and the xlite softphones but cant get more that the *98 transfer feature working on the analog phones.

    Not so sure if the service code being utilize by the FXS is the same as what is mentioned in VSA.Then again, the manual says "dial the corresponding * code on the client station" and if you look at an SPA9xx phone, it has the following codes defined for call park and call unpark code.
    *38
    *39

  • Pay Cycle Manager system check payments with Financial Gateway?

    Can PeopleSoft Payables Pay Cycle Manager be used to system check payment information Financial Gateway? Per PBooks "The Pay Cycle Manager only settles payments of EFT, ACH, and WIR payment methods through PeopleSoft Financial Gateway." However, can the process be configured or modified in some way to also accommodate system checks?
    The client is not producing system checks from PeopleSoft Payables but, rather, using a 3rd-party application (MHC) to administer system check printing, ACH and credit card payments, and 1099 reporting. The desire to define those system check payments administered via MHC as system checks in PeopleSoft, although truly none are being produced from within PeopleSoft.
    By leveraging the Payment Request process payment information is created that can not only be sent to MHC but any target system that also requires payment information. A number of other internal systems also require this information and my intent is to use the data that is staged in Financial Gateway as a standard data structure for any target system which requires the data. However, as mentioned above, the payment information needs to include all payment methods, including system checks.
    Please advise. Any recommendations or alternative approaches are appreciated :-)

    Did you ever find an answer to your question?
    Thanks

  • Call manager directory number starting with \+

    I have a CUCM ver 8. Some of the directory numbers were configured to use \+, such as \+12025551201.
    The problem is, when I tried to retrieve CDR, using the number \+12025551201,  it comes up with:
    Error Code     Error Description
    10021     There are no matching records
    I tried to remove the \+ sign, it is still the same.
    So what is workaround?

    Hi
    Try to pull the CDR by without mentioning anything for the busy hours, if u got any reports go through the actual digits in the origin.
    If fails we need to go for CDR configuration, check and let me know

  • Using Parallel Port with Outport.vi Problem

    Hello,
    I am trying to use my parallel port to control a relay network and have run into a problem. I am using the outport instead of visa because for some reason I get an error with visa and outport seems more simple. The problem I am having is that my program doesn't seem to be able to initially take control of the port. What I mean by this is that if I restart the computer and open/run my program, I get an incorrect output on the parallel port. However, if I run one of the example programs for controlling the paralle port using outport (attached) (I believe the one I use is called Reading and writing to parallel port using loops) I am able to control the output to the parallel port. Also, after the example has run, my program works correctly. However, if I restart my computer again and run my program first it can no longer control the port correctly. So the problem seems to be that my program isn't initializing the port correctly or assessing it right at the beginning of the program. However, looking at the example program I don't really see what they are doing that I am not. I have the correct port address. 
    My program takes values from a text file and displays them on the port and that works correctly. 
    Attachments:
    CircuitTopModule.vi ‏26 KB
    parallel port examples.llb ‏72 KB

    Hi Jag213, I'm glad you were able to resolve the issues you discussed on the other forum related to this issue.
    Now that you have it working, I would recommend a few things:
    1. Just try modifying one of the existing examples and see what you can get away with removing in order to keep it working the first time.
    2. Try modifying the timing on your example - 10 seconds is a long time to wait between each week, I wonder if you are getting a time out? Do the examples work when you insert that kind of timing delay?
    3. Add the In Port.vi into your code - this may be related to getting your Out Port.vi to work correctly.
    4. Your code controls 8-bits on the parallel port, while the examples control 32-bits. Do all 32 bits need to be initalized? Looking at the Parellel Port Read and Write Loop.vi Example, in the IO Connector Status, the 31st bit controls whether the target is initialized.
    Play with these settings and see if you can get yours to work the first. If all else fails, build your program to run off of one of the examples. For example, have the while loop run once, and then call yours as a SubVI.
    Good luck!
    Joey S.
    Software Product Manager
    National Instruments

  • Ringtones and background images not available after call manager upgrade

    Hi,
          We have upgraded our call manager from version 8.5 to 10.5.  Once after the upgrade we lost all the Ringtones and background images except the two default ringtone and background images.  we got 8945 sccp phones(running 9-3-1 firmware) and 9951 sip phones(running 9-4-1 firmware).  Both these phones lost these list.  However the ringlist.xml is available in the tftp server with all the ringtones and the phones are pointed to the right tftp servers.  I tried to restart the tftp servers and tried again, however that didn't help.   we are using call manager 10.5 and h323 voice gateway.  Could anyone please help on this.
    Thanks
    Barry

    Hi Tony,
         I can see the ringtone files in the call manager (osadmin>tftp file mgmt), i have also restarted the tftp services, but it didn't help.  I believe you advised to re-upload the ringlist file (Ringlist.xml) and try again. I will try this and update you.  Please let me know if you have any other suggestions.
    Thanks
    Barry

  • Restricting FXS ports to internal calls only

    Hi,
    I have recently intalled Call Manager 8.5.1 with a H323 Gateway. On the gateway, I have a number of FXS ports for lobby phones. Is there a way I can restrict these phones to allow only internal calls only? Do I need to use COR lists like in Call Manager express or is there a  more practical way?
    Thanks,
    Derek

    Hi Derek,
    It sounds like these FXS ports are NOT registered to CUCM 8.5.1?  If they aren't, then yes COR lists is the most pratical way to do this.  You could do a "connection plar xxxx" to a receptionist extension and her her/him forward the calls to the correct extension.

  • Integration Call Manager with Microsoft's tools

    Hello,
    My costumer has call-manager 5.1 and Cisco Unity 5.0 (voice e-mail only) working perfectly on his company.
    Besides, he has Microsoft Outlook 2007 and MS-Office Communicator with presence server.
    He wants to use MS's tools integrated with Cisco call-manager.
    Ex
    Listen to voice e-mails directly on Outlook 2007 and on UNITY.
    Use office communicator (presence) according to the status of user's phone; also implementing functions like "click-to-dial".
    Is there any kind of software or license that I should get from Cisco to implement these functions?

    Please I need help.

  • SPA112 use with Call Manager

    We have used ATA 186 devices with our Call Manager system for use with fax machines and analog phones in a manufacturing environment.  I am hopeful that the SPA112 can be used as a lower cost alternative to the older ATAs.  
    I have searched for basic configuration information for use with Call Manager but haven't come across anything. 
    Can these devices be used with Call Manager and is there basic information available on how to configure them?
    Thanks.

    The SPA112 is essentially the same as the Linksys PAP2t adapter.
    They both use SIP protocol, and can be added to Callmanager, but I don't think the SPA112 is supported in this configuration.
    I was able to get the SPA112 to work with CallManager by adding it as an Advanced SIP device.  That uses more licenses (6 I think).
    https://supportforums.cisco.com/thread/2082101
    That details getting a Linksys PAP2 device working with CallManager 7.1
    I got SPA112's working by using the info in that link.  You have to set it all up manually, but it does work.

Maybe you are looking for