Cant telnet router B's loopback from Router A

Hello gentlemen.. :)
picture worth a 1000 words...
please check the attached image which describes my case

- can you telnet to that loopback from HQ router? Locally?
- can you telnet from Branch router using different source address for telnet packets?
BR,
Dragan

Similar Messages

C309g causes router to stop internet from router

I bought a c309 and connected wirelessly to a Netgear N-300 router (Comcast modem), I am able to print from my laptop wirelessly but after a few minutes i find none of the computers in the house can receive internet (though strangely my son's computer can still get Slacker, but not internet explorer). There is no problem with the modem as I do get internet if I connect directly to the modem. i changed the IP on the printer manually to make sure it is not the same as the primary server, but still I get the same issue. Appreciate any advice.
This question was solved.
View Solution.

First, update firmware for your router. A few versions of Netgear N routers had firmware that did not play nice with HP wireless printers.
Next, Setting a static IP in this way has fixed this issue with others':
Let's set a static IP address for the printer:
- Print a Network Config Page from the front of the printer. Note the printer's IP address.
- Type that IP address into a browser to reveal the printer's internal settings.
- Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
- On this screen you want to set a Manual IP. Enter the current IP address.
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Leave the gateway and DNS blank. Click 'Apply'
Now, shut down the router and printer, start the router, wait, then start the printer.
After this you may need to redo 'Add a Printer' using the new IP address.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

My iphone 3Gs only has wi fi access within 1 to 2 meters from router

My iphone 3Gs only has wi fi access within 1 to 2 meters from router. It had been working normally for the last two years. I changed wifi modem a couple of months ago but still worked fine until a couple of weeks ago. I have the same problem with other wifi networks. The iPhone only picks them up if it's within 1 to 2 m of the box.
I've tried turning the phone and the modem on & off, restoring the phone and different wifi networks - no change, still has the same problem.
Can anyone suggest what might be wrong or what I could try next?

These are the symptoms of a loose or detached Flex Cable # 6 at the top of the Logic Board.

The name of my wireless network in the form of my modem router is not read from the iPhone, while the first era.Il my ipad does not read the network but I surf the internet. Why? What can I do?

The name of my wireless network in the form of my modem router is not read from the iPhone, while the first era.Il my ipad does not read the network but I surf the internet. Why? What can I do?

Can I use this DIR-635 to extend the WiFi network of the "Belgacom" WiFi?
To answer this question correctly, a user would need to have a DIR-635 router connected by Ethernet to a Belgacom router.
If you think about it, the chances of another user who has these two same devices configured this way and also being on an Apple support forum to see your post are about zero.
The following might work, but you will not know until you try.
Configure the DIR-635 to provide a wireless network that uses the exact same wireless network name, exact same wireless security and exact same password as the Belgacom wireless router. Make sure that the DIR-635 is configured in Bridge Mode.
Can I purchase and set-up an Apple Airport Express or Apple Airport Extreme on my level 1 (the ethernet cable running from level 2 to level 1 could plug-into either of those)
The AirPort Express or AirPort Extreme would need to be configured exactly the same way as mentioned above.
(What is the difference in the 2 -- one is about twice the price of the other…)
http://www.apple.com/wifi/

Mac mini server refuses to get DHCP address from router

Everything was going along fine. But after a power outage the server goes to a 169. address when the router puts out 198. addresses. If I put a static 198. address in it sees the network but won't connect to the internet. I've flashed the router (everything else sees the router fine, 3 computers and a time capsule). I've had the hardware checked at the Apple store - it picked up an address right away. After narrowing everything down the problem has to be in the operating system. I even did a full time machine restore to the day before the storm. No luck. Anyone heard of this problem.

Mauricette has a point.
A server function is not designed to accept a floating or dynamic IP address. If that is the case, how do you create firewall rules that prevent those unnnecessary ports being left opened from being attacked by rogue machines in Romania and China on a hourly basis when you announce to the world that your server is available if the server IP address keep changing due to the DHCP lease change? Yes, they do have bots that do this VERY EFFICIENTLY!
By changing the very nature of your firewall rules by working with DHCP, you are opening ports you do not know to accommodate DHCP dynamic addressing, which was the reason why your Mac Mini Server stopped working in the first place. It's ok for a client, since a client isn't serving any files to any one right.
By using client based firewall rules, you are exposing your server to attacks and when they get through your Mini server, which they can if they are persistent, they get into your home network and then whatever file server services you have opened and unprotected at the time WILL BE copied by these people easily.
I have a client once who did just that. She was attacked, the hacker went through her network like a rampaging bull. They were from China. My Synology RAID server gets this attack all the time, but I have a well establish IDS system and the Synology RAID has logs that tracks attacks.
For a server setup. Use static IP and then build a strong firewall around it and protect it and never compromise.
Recently, I just noticed someone somehow hacked and broke my WPA-PSK AES passkey for one of my Wireless N network router. It was not set up with a strong password though, but thankgod I had a firewall around that so my internal networks were safe. So this teaches you that if someone wants in bad, they will get in.
Hope this helps.

My iPHONE 5 wifi is NOT working when am 3 feet away from router while my iPhone 4s has full signal all the time.Please help.

My iPHONE 5 wifi is NOT working when am 3 feet away from router while my iPhone 4s has full signal all the time.Please help.

The problem would seem to be in the firewall in your router. Have you tried disabling it? I assume you've updated the router firmware, right? Consider bypassing the ISP provided router (using it as a modem only) and unsing another device such as an Aiport Express.

Automatic purchase requisition created from routing needs to be have material no. information in it.

Hello Experts,
There are some operations in my routing where external service , from an outside vendor shall be required.
We are doing this by using a particular control key PP02, for this routing, so that purchase requisition is created automatically, when the production order is created.
Through customization, I have also been able to make the setting so that instead of single, collective requisition gets created for the entire order.The requisition that is getting created is a service requisition and can be later converted to a Purchase order.
Requirement :- I need to enter material information in this requisition automatically. By material, I mean the material no. and preferably qty of the material, which will have to be sent out to the external vendor for his services.
How can I achieve this, in SAP?
Regards
P.R

Hello Caetano,
Right now we are not considering best practices , so not considering BADI implementation as such.
So far I have done the following:
I created a subcontracting purchasing info record for the material and a vendor.
Then, I have created a routing for the material and the operation which expects to go for external processing, I have used control key YBP2 (tried with PP02) in it.
I have assigned the subcontracting PIR under the external processing section of this operation in the routing.
My Production version combines the BOM and routing in the material master.
Now ,,when I try to create the production order, I get the following errors in succession:
Control key YBP2: Maintain external processing data
Message no. CO558
Diagnosis
The control key specifies that the operation is processed externally. However, not all data relevant to external processing has been maintained.
respond by entering the material group where the cursor is.
Then I get the following error.
Material class differs from material class from info record
Message no. 06354
Diagnosis
The material class or material group of the info record differs from that of the item.
I checked in the material master and the material group there is same as the material group in the info record . Field name is MATKL.
What material class is it talking about?
I cannot get past this error and therefore cannot complete the order creation.
Regards
P.R

Re: (forte-users) No response from Router partition

Sounds like what we have been experiencing here, on Unix.
According to Forté, upgrading to 3M should resolve it. Unfortunately, we
can't
confirm it yet, as we are in the process of upgrading and testing.
I believe this is documented as an "internal" Forté bug report.
Hope this hels.
Daniel Désy
BORN
----- Original Message -----
From: "Pabbaraju, Ramarao (EXP N-IONIDEA)" <ramarao.pabbarajulmco.com>
To: "Forte-Users (E-mail)" <forte-userslists.xpedior.com>
Sent: Tuesday, November 14, 2000 10:46 AM
Subject: (forte-users) No response from Router partition
Hi All,
One of the router partitions on NT server stops responding once in awhile. We can not get to it through escript or econsole and the only
solution we have is to shutdown the ftexec using task manager and start
the partition again. We don't see any error messages in the log except
this line "LbRouter::AttachToRouter - Ignoring DOM version: -1 obj
version: 0". Does anyone have any idea what this means? Is there any way
to figure out the problem? We are using Forte 3L3. Thanks in advance.
Thanks
Ramarao--
For the archives, go to: http://lists.xpedior.com/forte-users and use
the login: forte and the password: archive. To unsubscribe, send in a
new
email the word: 'Unsubscribe' to: forte-users-requestlists.xpedior.com

My guess is, your third service object is not referenced.
-----Original Message-----
From: Forte App [mailto:forteapphotmail.com]
Sent: Wednesday, May 17, 2000 3:08 PM
To: kamranaminyahoo.com
Subject: (forte-users) Partition problem
Hello Everyone,
I have three (3) service objects in my project and when i went into
partition workshop i can only see two service objects instead of three and
all the three service objects properties settings are same
iam using Forte 3.0L2.
Thanks in Advance
For the archives, go to: http://lists.xpedior.com/forte-users and use
the login: forte and the password: archive. To unsubscribe, send in a new
email the word: 'Unsubscribe' to: forte-users-requestlists.xpedior.com

Can I use the Cisco license transfer tool to rehost licenses from router 2900 to new router 2900? is not rma process

Can I use the Cisco license transfer tool to rehost licenses from router 2900 to new router 2900? is not rma process
thank you

Yes you can.
Alternatively, you can email [email protected]

Poor Performance from Router MI424WR

Purchased Verizon internet for the first time a few months ago, was told the coverage was 200 feet from router. My home is 2 stories, have no internet in lower level (router is on top floor), cannot get signal on deck, which is literally 50 feet from router. Is this what I should expect for my money? I used to have cable modem and separate router, and had zero problems in 3-story, 3500 sq ft house. Should I have to buy an extender, isn't there other options Verizon can offer me for what I am paying? Or maybe someone has a suggestion on how to fix. Really disappointed in this service, plus if you try to call for support, the wait time is always over an hour. How can a company get away with this? Really digusted as I work from home on the net, and can only work in 50% of my living space. Thanks for any suggestions. Steve

chefdijour wrote:
I am not sure what you mean by "change the channel that the router is using for wireless devices and see if that helps"? Trying to get someone on the phone of even arrange a service visit is all but impossible, a sad state of affairs for a such a large company that lauds itself on customer service. I long for cable again. FYI, you're talking to other customers here. If you want a response from Verizon, you need to call or chat with them. To adjust WiFI settings on the router, you'll need to login to it's administrative management web page. Typical installs will put it at http://192.168.1.1 (go ahead, click on that link). The username is "admin". The password is printed on the router's label, unless you've changed it. A simple google search for "mi424wr manual" will locate the documentation on Verizon's web site. If that doesn't answer your questions about how to adjust the settings, post back and you'll get some more help. If you can't figure this out yourself (with help from forums like this or other online resources), you'd be better off hiring a local network tech to do the work rather than a Verizon tech visit. They typically do not do this type of in home support. If you do get Verizon to send a tech for this, they will charge you a lot of money for it as it's not a problem with their system. Enjoy.

DIR creation from routing

Hello All,
I have a requirement to generate a document in SAP DMS (CV01N) for the assembly instruction using the process steps from routing(CA01).This would include inserting an assembly picture (JPEG) into original file which would reside in DMS and would link back to routing using the object link. The request for this process was to avoid the manual creation of the worksheet from routing. The series of steps in routing would be pulled into a excel document inside a DIR at click of a button from the routing screen. Updating the routing from the DIR screen should be blocked wit an error message.
Please let me know if you guys have come across such requirements and what could be the possible solutions.
Thanks in advance,
P-

Hi Paddy,
For this requirement a z-develipment needs to be done with help of respective screen exits. You need to consult with Abap'r. In standard environment it's not feasible.
Hope this will help.
Regards,
Ravindra

Create DIR from routing..

Hello All,
I have a requirement to generate a document in SAP DMS (CV01N) for the assembly instruction using the process steps from routing(CA01).This would include inserting an assembly picture (JPEG) into original file which would reside in DMS and would link back to routing using the object link. The request for this process was to avoid the manual creation of the worksheet from routing. The series of steps in routing would be pulled into a excel document inside a DIR at click of a button from the routing screen. Updating the routing from the DIR screen should be blocked wit an error message.
Please let me know if you guys have come across such requirements and what could be the possible solutions.
Thanks in advance,
P-

Hi chandu,
Its working for rest of object links but for sales order its not showing create button. Is this screen shot taken from VA01/02 transaction? I guess you have share the screenshot from material master .
There is no create document button after making below setting..
Create Document field, I have tried with value 1 as well as 2.
/Tilak

Cant connect to certain websites with WRK54G router

Hello all, I have a WRK54G router with SBC as my ISP. I am running Windows XP and I can not connect to disneyshopping.com, nor enterprise.com with the router plugged. If I unplug the router and connect the computer directly to the SBC router I have no problems. I use both IE7 and Firefox, with all java and flash updates inplace. If there is something in the settings of the Linksys router I need to change, can somebody please help. Thank you all in advance for your help!

Looks like your DNS servers are no working, check this on how to assign DNS servers and other network info on your computer. If you get the IP and other network info from router, then go to router management page, assign following DNS servers on its DHCP part.
Use these 2 free DNS servers from OpenDNS and try again..Should work..
208.67.222.222
208.67.220.220
picoHat
Home Network, Wireless Network and Computer Networking Made Easy

Need to fetch the plant from route and country

Hi all,
I need to fetch the "plant" from "route" and "country".
is there any table having all the 3 fields, or any way to link these 3 fields ??
thanks
Sri

Hi Sri,
Try the COPA docs table CE1*
Regards,
Sandeep

FM to get work center information from routing

Hi all,
Is there any FM to get work center information from routing?
Points assured.
Thanks and regards,
Nilesh

Use This FM
CR_WORKSTATION_READ_ROUTING,ROUTING_DISPLAY
Use table CRHD ,MAPL
Please reward if useful.

Cant telnet router B's loopback from Router A

Similar Messages

Maybe you are looking for