Convert elements using DAQCard-6024E to USB-6221using LabVIEW 2009

I just received an old project, the VI was mainly designed using DAQCard-6024E. Since we'd upgrade the equipment, and the DAQCard-6024E is no long used. However, they want to keep the similar front panel. I am trying to convert the pull-down menu that I can use with USB-6221 with Windows 7, but I don't know how. Can anyone help?
Windows 7, NI USB-6221, LabVIEW 2009 sp1
Solved!
Go to Solution.
Attachments:
test_1.vi ‏45 KB

Hi smoothengine007,
You should be able to use this document's Digital Output section to see how to modify your VI:
Transition from Traditional NI-DAQ to NI-DAQmx in LabVIEW
It looks like the rest of your code can stay intact if you just replace your Traditional DAQ VIs with DAQmx VIs.
Regards,
Message Edited by Dustin D on 02-23-2010 11:59 AM
Dustin D

Similar Messages

Error in ni visa control out for usb in labview 2009

Hi,
I am using labview 2009 in which i have made a vi which communicates with a pic controller through USB interface.
the vi is working fine in labview 8.6. I tried it in two PCs. but when i run that vi in a PC with labview 2009 then the VISA CONTROL OUT.vi gives error "0xBFFF003E : Could not perform operation because of i o error.". while the control in.vi works fine in both the labview versions and any other PC that i tried.
I have run the application in total of 4 PCs with same set of cards/interfaces. two of them having labview 8.6 are running fine and giving no error but other two with labview 2009 are giving error.
and it doesn't stop here.... i searched in the vi and did some experiment and found that when i give Request value input to control out.vi as "0x36 "(as required by my PIC program) then it is giving error but when i give other value such as " 0x35 or 34 or 55"(used for other purpose) then it is not giving error.
Can it be a PIC programming problem? (i dont think so as everything is fine in other PC with LV 8.6)
I have already explored the ni forum for this error solution but could not find helpful.
Can anyone solve my problem?

I installed labview 8.6 in that machine and made a small program with only 3 vis (visa open session, visa close session and visa usb control out.vi) which is working in LV 8.6 platform.
Sorry the above statement is not correct actually.
When i run the program in LV 8.6 it giving that same error but this time it is not displayed as pop up window. so i could not judge that error was still there.

Error 10452 using DAQCard 6024E

When I try to run a .vi that get data from a sensor... I get error 10452 and it says 'no interupt is available for use.' I am using a HP Pavillion zd7000 laptop in a WinXP environment. I have attempted changing the IRQ to no avail... has anyone had a similar problem and figured out a solution?

THe best thing to do is to check to see what IRQ is currently assigned to your DAQCard, and determine if any other devices in your system are also using that same IRQ. If there is a conflict, then the problems you described will occur. Ways to resolve it include disabling or changing the IRQ of the other conflicting device to another IRQ value, or changing the IRQ your DAQCard is using to a value which is currently unused.
The following thread discusses a similar issue and gives suggestions:
http://forums.ni.com/ni/board/message?board.id=250&message.id=5394
I am curious, which IRQ values have you attempted to use thus far with no luck ?

How to use IXXAT CAN to USB in LabVIEW for CAN read, when I am having VCI V3 driver?

I am having VCI V3 driver for IXXAT CAN to USB.How to use that in LV for reading data from CAN device.

Did you check the settings to make sure that the Password Manager is enabled?
*Tools > Options > Security: Passwords: "Remember passwords for sites"
Make sure that you do not run Firefox in (permanent) Private Browsing mode.
*https://support.mozilla.org/kb/Private+Browsing
*Tools > Options > Privacy: Use custom settings for history
*Deselect: [ ] "Always use private browsing mode"
See also:
*http://kb.mozillazine.org/User_name_and_password_not_remembered
*http://kb.mozillazine.org/signon.autofillForms

WIth LabVIEW how do I control an instrument with a RS232 output, using a RS232 to USB converter cable.

WIth LabVIEW how do I control an instrument with a RS232 output, using a RS232 to USB converter cable since I dont have rs232 ports. I have two instruments that I want to control in this manner. One is an Imada ZPS force gage with RS232 output. The other is a Panasonic HL-G103-S-J laser micrometer sensor which is RS422. I've done considerable LabVIEW programming using GPIB but I have no experience with devices like these. Any tutorial or examples would be greatly appreciated.
Thanks.
Solved!
Go to Solution.

I understand that you want to control a device which having RS 232 port as output. If so, you can use an USB-RS232 cable from PC to device and you can control or monitor the device.
See this link http://zone.ni.com/devzone/cda/epd/p/id/2669
Also, first check the device in hyperterminal and then continue to program in labVIEW. You can find the serial VI's in Instrument I/O.

Can the usb camera converter be used with a flash drive or scaning device?

can the usb camera converter be used with a flash drive or scaning device?

No.
iOS does not have scanner drivers nor does the connector supply enough power.
Flash drive would kind of work, would need to have a DCIM folder-probably wouldn't see whole drive(?)
Then again this exists, uses wifi:
http://i.tuaw.com/2011/05/16/goflex-satellite-is-your-ipads-portable-wireless-ha rd-drive/

Are there compatibility issues with using labview 4.0.1 with a DAQCARD 6024E. Which Ni-daq version should I use? Operating system?

I recently purchased a DAQCard 6024E and am trying to set it up on a windows XP laptop. Labview 4.0.1 vis do not seem to function. Do I have some compatibility issues? Thanks

Hello;
The oldest version of NI-DAQ that supports that card of yours is 6.6, which doesn't support Labview 4. Furthermore, the only NI-DAQ version that supports windows XP is the latest one, 6.9.2, and the Labview version that supports that same OS is 6.1.
Since you will have to upgrade Labview to be able to work with that DAQ card of yours, I advise you to upgrade to Labview 6.1, so you can work under XP also.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

DaqCard 6024E intermittant with Windows XP

I am still having trouble running the PCMCIA DaqCard 6024E reliability
on a Winbook running home version XP. I could get by, but my customers
can't.
I ordered two cards, one to upgrade a Winbook laptop running Windows Me
(from a DaqCard 500) (a little over a year old) and the other for a new
Winbook which came with XP installed. I also have a new Winbook running
XP (also home version) and working fine with a DaqPad 6020E from the USB
port. I am using the latest version of NIDaq, 6.9.2. Once MAX sees the
card, LabVIEW has no problems.
Both of the DaqCards cards run fine in the old Winbook running Me.
Neither of the PCMCIA 6024E cards will run reliably with the XP system.
>From a cold boot, I have to restart several times (usually between 5 and
10 times) before the card is recognized (little icon in task bar). Or
if I boot once and then just unplug and replug the card - hot - it also
requires about 5 to 10 of these cycles. Once its recognized, if I
unplug and replug the card it will not fail to recognize the card until
between 15 and 20 tries.
Just to verify that the laptop is ok, I bought a PCMCIA ethernet card.
The box for the ethernet card (Netgear FA411) indicated that it would
run with Windows 95/98/Me and a sticker on the cellophane wrapper said
"Works with Windows XP". The sticker (afterthought) suggested to me
that if it would work with Windows 95/98/Me it would also work with XP.
I rebooted 25 times and the computer recognized it every time. I also
unplugged and plugged the either net card - hot - 25 times and the
computer recognized it every time.
Winbook will not guarantee survival if I try to load 98 or Me in the new
computer. I think these systems are assembled and loaded in China and
they don't have the drivers in Ohio. By the way, this is my fifth
Winbook, and this is my first problem. Otherwise XP seems to run better
than Me. My new Winbook with XP and the DaqPad has never failed. I
have been using it nearly every day since February. I developed both of
the DacCard systems with it.
I think the Winbooks, about $1000, and the DaqCards are perfect for my
customers. I hope we can fix this problem.
For the present, my clients are using the computers in the lab and are
able to leave them on continuously 24X7. But soon they will get
approvals and will have to go to the clinic for their study. They have
to move a cart into a room, plug in the equipment and can't be messing
with the cards when the room is $700 per hour and the Doctors are upset
(that's a mild term). If we loose a study, we have lost a consenting
patient, (they are not easy to come by these days). I suppose, if I
have to, we could use DaqPAds, but I don't want to do that, nor do I
want the lose the restocking fee. In addition, I am currently putting
another system together, which I will deliver at the end of July. Not
sure what to buy, DaqCard or DaqPad (prefer DaqCard).
Thank, Harry
Harry L. Valenta, Jr., Ph.D.
Biomedical Research Associates, LLC
19042 E. Oxford Drive
Aurora, CO 80013-3812
phone and fax, 303 690 9688
[email protected]
[email protected]
www.bra-llc.com

Harry;
We don't have anything reported yet about Winbooks and Windows XP.
One thing you can try out though, is to see if the Socket drivers in use by the Winbook are the Native ones provided by Microsoft.
If they aren't uninstall those and install the NAtive ones from the Windows installation CD. If that is the case, it's probably the cause of the problem.
Hope this helps.
Filipe

Where can I find a document listing the instructions one can give the DAQCard-6024E card via the drivers?

Hi
We have bought the DAQcard-6024E card with it's drivers. (for PCMCIA)
I need a list of the instructions for setting up and reading the card using C++.
Where can I find such a list or document?
Thanks!

Hi eben,
I would recommend taking a look at the DAQ Getting Started Guide. This should have all the information you need. The location of the examples are listed on page 11.
Regards,
Kent
Digital Multimeter Home

Elements 8 does not support USB 2.0 Webcams?

From what I've gathered Adobe Premiere Elements 8 does not support USB 2.0 Webcams, only supporting USB 1.0 . Is there a driver or something to allow support for USB 2.0 Webcams?
- I have an Xbox Live Vision Camera.
- Windows 7 Professional (Awesome)
- Adobe Premiere Elements 8 trial version
I don't wat to buy this until I know my webcam will work. I liked the onion skinning ability of Adobe, but if I can't get my webcam to work it doesn't really help.
Thanks.

USB Web-cams pose all sorts of problems for most NLE programs. One possibility would be to use the capture software that came with the camera, of other, and then using the files in PrE. Depending on what the potential capture formats/CODEC's are available, conversion might be required.
Good luck,
Hunt

IRQ conflict on Dell Inspiron 5100 with DAQCard 6024E

Hi,
I have DELL INSPIRON 5100 and I am trying to make working my DAQCard 6024E , but it gives me following error on MAX Device Test Panel: The Device is not responding to the First Level IRQ. Would you like to continue anyway? Please see attached file for IRQ allocation on my Laptop.
What kind of drivers you requested from DELL? Can you please share those drivers so I can try out for my laptop.
Thanks,
Kishor Senjaliya"
Attachments:
IRQ.doc ‏85 KB

Wow, it looks like you have quite a bit of stuff on IRQ 10. My guess would be that another device is using that IRQ and not letting the 6024E use IRQ 10. Fortunately, it looks like you should have plenty of other resources available, so I would try to configure your card on another IRQ. Hopefully you can go to the properties on that card in the device manager and try to manualy set the IRQ to one that isn't being used. Good luck.
Steve.

DAQCard-6024Eが認識されない

担当者様，
NIのDAQCard-6024Eをラップトップ上で使用していますが，「Measurement ＆ Automation Explorer」でデバイスを認識してくれません．
ラップトップは，Panasonic社のCF-8Wで，OSはWindows　XP，ドライバはNIDAQ８５０とTDAQ７４４を使っています．
症状としては，「Measurement ＆ Automation Explorer」の「デバイスとインターフェイス」にカードが見えません．
XPの「デバイスマネージャ」をみると，「その他デバイス」の「PCMCA UNKNOWN_MANUFACTURER」として認識されています．
このドライバを
「ドライバの更新」
「一覧または特定の場所からインストールする」
「検索しないで，インストールするドライバを検索する」
「Data Acquisition Device」の「DAQCards-6024E」
として，ドライバを再インストールすると，
「ドライバ更新警告 …，ドライバがハードウェアと互換性があることを確認できなかったため，このデバイスをインストールしないことをお勧めします．…」と警告されます．
ドライバインストールを続行すると
「このハードウェアのインストール中に問題がありました」「このデバイスを開始できません．（コード１０）」となります．
そして，「デバイスマネージャ」では「DAQCard-6024E」のアイコンの上には「！」マークが付き，稼働しません．
ラップトップのカードスロットルの不良の可能性もあるため，他社のUSBカードを刺したとこと正常に稼働しています．
問題のDAQCard-6024Eを他のラップトップ（Windows XP）に入れますと問題なく認識していますので，DAQCard-6024Eに問題があるのではなさそうです．
更に分からない症状としては， DAQCard-6024Eが「PCMCIA MTD-0002」というデバイスとして認識されることがあることです．
ちょっと対処の手が尽きた感があり，Web上でもそれらしい対処法がみつからないため，知恵を借りたいと思います．

YKI様、
ご返信ありがとうございます。
YKI様の報告いただきました状況を考えますと、デバイス異常である可能性はあまり高くないかと存じます。
インストールされておりますNI-DAQmxバージョン8.5は XPにもVistaにも対応しておりますので、バージョンによる問題もございません。
（現に、YKI様がMAXで一度ご確認いただいております）
他のラップトップでは動作するとのことですが、
その他のラップトップ環境下においてもステッピングモータのコントローラのソフトウェア等ソフトウェアはインストールされておりますでしょうか。
もしかすると、その他に追加でインストールされたドライバもしくはソフトウェアが競合を起こしているかもしれません。
他のラップトップの環境と、
現在MAXおよびデバイスマネージャで認識されないラップトップの環境と比較してなにか大きな違いはないでしょうか。
また、デバイスをお送りいただく際の検査なのですが、
デバイスの認識、アナログ、デジタル入出力のテスト等、簡易的なものになります。
（主にお客様の報告いただいている現象が再現できるかを検証いたします）
期間は数日間になりますが、発送の時間を含めますと一週間（５営業日）でございます。
日本ナショナルインスツルメンツ株式会社｜　技術部　｜　小清水

DAQCard-6024E returns all zeros

I am using a DAQCard-6024E on a 120MHz Pentium desktop running Windows 95 and LabVIEW Run-time 6.1. To duplicate the problem, I built an executable for the Acquire N Scans example and entered Channels 3:0, Number of Scans 1000, Scan rate 20000, and clicked Run Continuously. It works fine for an hour or so, (with occasional timeouts), but then the signal changes to identically zero (no noise and no error messages). After this, the only way I have found to get it going again is to power down the computer or hot unplug/plug the DAQCard-6024E. Re-booting without turning off the power does not work. I have been using the same DAQCard-6024E on another (much faster) computer running Windows 98 and never seen this problem.
What is the cause of
this problem and what can I do about it?

See
http://exchange.ni.com/servlet/Redirect?id=8470237
Regards
Filipe A.
Applications Engineer
National Instruments

Pin assignment for DAQCard-6024E

Card is installed and functioning with 3rd party software. I want to build a simple interface to measure input analogue signals. We bought a bread board from NI (CB-68LPR it says) with a cable to connect to PCMCIA DAQCard 6024E. Now I have access to all 56 pins. But the card came from my 3rd party person and I don't have any manuals and cannot find any infomation about the pin assignments. I found reference to the "DAQ Assistant", but this has not been installed on my system (Measurement and Automation Explorer is there and I can run the Test Panel). Ultimately I will use a program called WINview to monitor my input signals. This seems pretty basic.
David

Hello David,
I think all you are looking for are the pin assignments for the DAQCard-6024E device. This information can be found on page 4-2 of the 6024E User Manual.
Post back if this was not the only information you were looking for.
Best Regards,
Jared A

Convert internal powerbook keyboard into external usb keyboard??

I want to convert a used powerbook G4 keyboard into an external usb keyboard for my MBP. What seems to be needed is a connector with a slot on one side for the ribbon on the powerbook keyboard and on the other side a usb slot. I like the idea of having an external keyboard for my MBP with the same look and feel as the MBP's keyboard. Any ideas?
Mac OS X (10.4.8)
Mac OS X (10.4.8)

I checked system profiler and the internal keyboard is both bluetooth and usb. So all that would be needed is a connector from keyboard ribbon to usb port. Probably none exist in the market as this is an unusual thing. But perhaps I can jerryrig something. It's just the look and feel of the MBP keyboard that I'd like to emulate on an external keyboard. You know, as if the external keyboard was designed exclusively for a MacBook Pro.
Mac OS X (10.4.8)

Convert elements using DAQCard-6024E to USB-6221using LabVIEW 2009

Similar Messages

Maybe you are looking for