Direct traffic onto an LSP based on packets ToS value

Hello...
I am trying to push traffic onto an LSP thats mutiple paths created as below.
interface Tunnel3080
ip unnumbered Loopback0
tunnel destination 10.253.253.136
tunnel mode mpls traffic-eng
tunnel mpls traffic-eng path-option 11 explicit name CTel-C32-CGx-CSnf-Cwil
tunnel mpls traffic-eng path-option 12 explicit name CTel-CGlb-C1275-CMar-CWil
tunnel mpls traffic-eng path-option protect 11 explicit name CTel-CGlb-C1275-CMar-CWil
ip explicit-path name CTel-CGlb-C1275-CMar-CWil enable
next-address 10.254.0.241
next-address 10.254.0.242
next-address 10.254.0.2
next-address 10.254.1.82
next-address 10.254.13.1
ip explicit-path name CTel-C32-CGx-CSnf-Cwil enable
next-address 10.254.0.242
next-address 10.254.0.241
next-address 10.254.0.2
next-address 10.254.1.82
next-address 10.254.13.1
Traffic is coming in from an interface vlan 503; and is going to lets say 10.11.1.2.
I've an ACL as below to catch the traffic into an ACL.
ip access-list extended TOS9TrafficTo10-11-1
   10 permit ip 10.32.21.2 10.11.1.2 tos 9
I tried with below to direct the traffic onto an above tunnel LSP.
route-map BO_LA permit 10
match ip address TOS9TrafficTo10-11-1
set interface Tunnel3080
and then applied the map to the interface as below...
interface vlan 503
ip policy route-map BO_LA
Its not working..   and need some assistance.. I know route maps are not the solution here as they're used for routes and not the actual traffic, I believe. Is there any other solution.
-Tarkesh

Tarkesh,
This should actually work because a route-map can also be used for policy-based routing and not just for routing information manipulation. I am in fact surprised that your configuration has no effect. The first thing coming to my mind here: is the interface Vlan503 the incoming interface for this traffic you want to send via specific MPLS TE tunnels? Is the traffic actually routed, i.e. passing through the Vlan503, or is it simply switched within VLAN 503?
Also, how do you know your configuration has no effect?
There is an option of class-based tunnel selection for ingress traffic, however, that feature is supported only on selected platforms. You can read (much) more here:
http://www.cisco.com/en/US/docs/ios/mpls/configuration/guide/mp_te_tun_select.html

Similar Messages

Directing traffic to specific server based on URL

I've got 2 servers in a server farm on round robin load balancing set up. Right now, it load balances requests to www.abc.com. I would like all requests for www.abc.com/admin to go to server A all the time. What's the best way of accomplishing this? I've tried setting up stickiness with no luck so I'm not sure if that's the right approach. Thanks.

First create class-map with your url:
class-map type http loadbalance match-any ABC
3 match http url /admin.*
Next create new server-farm with only one server:
serverfarm host SERVERFARM.SERVER1
rserver RSERVER.ONE 80
    probe PROBE.ONE
    inservice
Next modify your policy-map type load-balance:
policy-map type loadbalance first-match POLICY.LB
class ABC
    serverfarm SERVERFARM.SERVER1
class class-default
    sticky-serverfarm STICKY.SERVERFARM.ONE
Everything what is matched by Class-map will be forwarded to Serverfarm. Simple and very scalable.

ACE 4710 how to direct traffic by source ip

I would like to know in the simplest terms how to use the source ip of the request to direct traffic to 2 different server farms.
One ip address source range to one server farm and all other ip address sources to another server farm.

Good morning,
It is possible to match the source IP of the client as a parameter for L7 class-map. See the link below for more details
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/ace/vA5_1_0/configuration/slb/guide/classlb.html#wp1117372
For your setup, you could just create two different class-maps (one for each source range) mapped to two different serverfarms.
I hope this helps
Daniel

Directing workflow transition based on form element value

Question 1
=======
How can workflow change values in a form element?
Example: We have an expense aproval form.
If the form transits from state ManagerA to state Reject, I want the form element Rejected by: to be automaticaly set to value ManageA.
How ho achieve this?
Question 2:
========
How can a workflow read a form element and based on the element value automatically transit to other state?
Example: An expense aproval form is in state ManagerA.
If a user set the form element Rejected by manually to the value ManagerA, I want the form to be automatically transited from state ManagerA to state Rejected.
How ho achieve this?

Originally Posted by dangross
Answer to question 2 is: Add a transition of type "Transition on Entry Data Value" and configure it accordingly.
Dangross, thanks for the reply. Yeah, that Transition on Entry Data Value will do the job.

Looking for help with javascript to autofill checkboxes based on a numeric value.

I have a numeric field that I would like to have 1 - checkbox
out of five autofilled based on a numeric value.
For instance the numeric value is TotalPoints
If the TotalPoints Value is >10 autofill this checkbox
If the TotalPoints Value is 10 - 19 autofill this checkbox
If the TotalPoints Value is 20 - 49 autofill this checkbox
If the TotalPoints Value is 50 - 69 autofill this checkbox
If the TotalPoints Value is 70+ autofill this checkbox
Assistance in writing the correct script for this would be greatly appreciated.

All the checkboxes have separate names.
Check box #1 is AssetClass.0 with the export value of 1
Check box #2 is AssetClass.1 with the export value of 2
Check box #3 is AssetClass.2 with the export value of 3
Check box #4 is AssetClass.3 with the export value of 4
Check box #5 is AssetClass.4 with the export value of 5
Score and StrategyUse the following calculation to determine your point score and indentify the appropriate strategy listed below.A. Add your points for questions 1 – 2.
B. Add your points for questions 3 – 12.
C. Subtract B from A. (Numeric Text Box) name is TotalPoints
Points Strategy Asset Class Mix (check boxes as named above)
0 – 10 Primarily Fixed Income: 80% Fixed Income; 20% Equity
10 – 19 Balanced Fixed Income-Oriented: 60% Fixed Income; 40% Equity
20 – 49 Balanced Equity-Oriented: 40% Fixed Income; 60% Equity
50 – 69 Primarily Equity: 20% Fixed Income; 80% Equity
70+ Equity: 95%; 5% Cash

How to set a default value for a drop down list box and then apply cascading based on the default value in Infopath 2010.

Hello Everyone
I have two drop downs. Both are coming from look up fields from two lists. i want to set a default value(first list item) for the first drop down list box and then apply cascading based on the default value for the next drop down list box. I found one article(http://www.bizsupportonline.net/infopath2010/display-first-item-drop-down-list-box-infopath-2010.htm)
where in i can set a default value but i can't apply cascading based on that default value. Any suggestions would be highly appreciated.
Thanks
Ramanjulu Naidu N

Hey Ramanjulu,
Take a look at the below article which I believe will answer your question.
http://basquang.wordpress.com/2010/03/29/cascading-drop-down-list-in-sharepoint-2010-using-infopath-2010/
Daniel Christian (MCTS)

Value for a parameter based on another parameter value

Hi all,
i am using report 6i and 10g db.
I have to create a report based on some parameter values. For example
Two parameter named as P_emp_code and P_emp_name
In the first parameter p_emp_code has list of values like empcode emp_full_name ie like 0002108 Vanitha Lanet Mendez
when user select P_emp_code i want to display the fullname in p_emp_name .
I tried as follows in list of values
select emp_fullname from emp_master where emp_code=:p_emp_code
then getting error bind variable cannot be used
Please suggest a way .
Thanks
Rincy

Hello,
The thing you are asking for set and editing the reports parameter form's value. Then i don't think you can do this by using the report parameter form.
But there are two alternatives for this task.
1. Create one form using form builder and pass the parameter and run the report from there. So, you can use the code as you showed in your first post.
2. Why don't you make this Title setting automatically? I Mean using the gender column (with decode/case condition) of same table.
-Ammad

Is there a way to hide some reports based on the selected values in prompt.

Hi Experts,
Is there a way to hide some reports based on the selected values in prompt.
For ex. if a year is selected in the prompt then the report should display year wise report.
If a year and half year both are selected in the drop down from prompt section then 2 reports should come.. One for year wise and another for half year wise.Kindly look into this.
Regards
Ashish

Hi,
Use presentation values in prompts for year,half,qtr and month.Example- For year-y is presentation variable in the same way for halfyear-h,qtr-q and month-m.
create four intermediate reports.Example-Report r1 with only year column,r2 with only halfyear column,r3 with qtr column and r4 with month column.
Make column in each report(r1,r2,r3,r4) is equal to their presentation variables(y,h,q,m).
Use four sections.
Section1-Place report that should come when only year.
section2-Place report that should come for year and halfyear.
Section3-Place report that should come for year,halfyear and qtr.
Section4-Place report that should come for year,halfyear,qtr and month.
Apply guided navigation for each section selecting guided navigation-
For section1-
properties->Guided navigation->check this Reference Source Request(Yes)->select report r1(year)->check this Show Section(if request returns row)
In the same way do for remaining section2(select r2),section3(select r3) and section4(select r4)
Thanks,
Srikanth
http://bintelligencegroup.wordpress.com/

How to find bpel instance in 11g based on the index values using Java APIs

Hi ,
In SOA10G we had option to find the instances based on the index value using Java APIs like below.
WhereCondition criteria= new WhereCondition(SQLDefs.CX_index_1 + " = ?");
criteria.setString(1, "indexValue");
Locator mLoc = getLocator();
IInstanceHandle[] foundInstances = mLoc.listInstancesByIndex(criteria);
Please tell me how to achieve the same functionality in SOA 11G using Java APIs
Regards,
Saba

I have multiple bpel in my composite. I checked in ci_indexes table and it shows the instance number of the bpel process. But the em console is showing only the composite instance number. when I opened composite instance, I could see all the bpel process with instance number in the audit trail. How can I find the the actual composite instance number that I should search for in the em console ???

Hide multiple rows in a dynamic table based on the row value.

Hi,
I need to hide multiple rows in a dynamic table based on the specific value of that row.
I cant find the right expression to do that.
please help

Go to the Row Properties, and in the Visibility tab, you have "Show or hide based on an expression". You can use this to write an expression that resolves to true if the row should be hidden, false otherwise.
Additionally, in the Matrix properties you should take a look at the filters section, perhaps you can achieve what you wish to achieve through there by removing the unnecessary rows instead of just hiding them.
It's only so much I can help you with the limited information. If you require further help, please provide us with more information such as what data are you displaying, what's the criteria to hiding rows, etc...
Regards
Andrew Borg Cardona

Sorting based on a specific value in Columns

Hi All,
Crystal 2008 version I have. And we are connecting to BW queries as source.
In a crosstab, I want to sort my row values based on a column value.
For example, in rows I have an element with three values . In column I have only one element(month), with couple of month values. My requirement is to sort rows based on a specific month (Mar'09 for example).
.....................Jan'09......Feb'09.....Mar'09
ABC...............10.............323...........33....
XYZ...............32..............33............11....
FGH...............5................34.............55...
But when I try to sort based on the Month, I can not select a specific value(mar'09). And it sorts based on the total value (sum of all months).
How can I achieve this problem?
Thanks
Ozan

For {Sort Value}, if you wanted to sort on the Jan column, then substitute the field name that your example shows as 10 in row ABC. For {row value}, substitute the field name that is used in the first column (ABC in the example).
In other words, take the value that you want to sort on, and put it in front of the value currently displaying as the row header. Then, sort on the results.
The purpose of the "000000000.00" is to make the length of the number, when converted to string, a consistent size. This is needed (a) so you know how many characters to strip off when displaying the row value, and (b) so the records don't sort as 1, 12, 2, 234, 235423, 25, 3, ...
HTH,
Carl

How to restrict a table with its set of data based on a column value in it?

Hi,
I have a scenario in which I have to show a set of data of a pivot table by restricting data based on a column value. I am creating BIP report whose source is from BIA ie.RPD. Based on a column value I want to restrict the data being displayed in the table. Since I also want the hidden data in the first table to be displayed in another table in the same report I cannot restrict the data at the query level i.e at RPD or at BIA. For this reason I used
<?xdofx:if saw3_ = 1?>
the pivot table
<?end if?>
But it does not restrict any data.
Also I tried using the if condition inside the table before the row level looping happens. But no good show even then.
How can I forgo this problem?
Regards,
The MM

Hi,
See : http://download.oracle.com/docs/cd/E12096_01/books/PubUser/T421739T481157.htm#4535373 regarding column and row.
Regards,
Colectionaru

Freight Calculation based on the net value of the Line item

Hi SAP Gurus,
I have one requirement for Freight calculation(Sales order is created through an IDOC) :
In the idoc,we will receive a freight dollar amount - which will be the total amount of freight.(example 100)
We will also receive sales dollar for each line item ,which is then passed to the pricing procedure, for a total amount of sales for that Sales order.
(examples below, for a total of 1500)
The 100 is to be posted to a freight G/L account.
The 100 is further divided by each profit center of the materials on the Sales order.
The freight is split out amongst the profit center , based on the net value of the line item.
Freight value to be allocated = Line item value/total value of the sales order * Freight amount.
Total of the sales order =1500
     Line item value     Freight value calculation     Profit center
Material A:      800          800/1500*100 = 53     Profit center A
Material B:     500          500/1500*100 = 33     Profit center B
Material C:      200          200/1500*100 = 13     Profit center C
Please let me know how to achieve this functionality in pricing procedure or what changes i need to make in Freight condition type.
Thanks in advance,
Bhakar Saha

Were you able to resolve this issue of allocating freight costs to line items/profit centers using the net value of the line items?

Dist. of Header Condition based on the material Value

Hi All,
I have one query regarding the header Condition.i have selected the Calculation type as B - fixed amount (mandatory) for a particular Condition type and also selected the header and Item condition indicator.Now if the material have more than one line item then the system distributes this condition based on the quantities in PO.
My client requirement is that they want to have a header condition as we are using now. But they want to distribute this header condition according to the material values for each line items in a PO. please Mention that this condition is a fixed value (mandatory).
So, how can we make a Fixed Value (Calculation type) for a header condition to be distributed among the line items based on the base Value?
Please revert back asap.
Sure, points will be awarded for the same.

as explained earlier ,
system is distributes the header amount on the basic of value calculated by Basic X qty
e.g.
header value =100
two line item
1 is with Rs 4/- and qty is 10
2 is with Rs 10/- and qty is 15
so distribution is
Rs 21.05/- for 1st item
and
Rs 78.94/- for 2ed item
regards,
sujit

Material Attribute value display based on cost center value

Hi,
Is it possible to display the material attribute value based on cost center value. I mean for some cost centers I would like to display the value of other characteristic in place of material attribute. I am trying to create a query on MP.
Any info in this regard will be appreciated.
Thank you.
Harshan

Hi Adi,
In Rows, Create a struture. Using New Selection, You can restrict the New Value to the cost center (Restrict again on those some cost centers) and material. And for this New Characteristic, you can have a attribute.

Direct traffic onto an LSP based on packets ToS value

Similar Messages

Maybe you are looking for