Error in Mobile Administrator, section device maintenance

Hi,
on our WebAS 6.40 SP18, I have configured the mobile admin according to the MI Installation Guide. When I access the section "Device Maintenance" and perform any search, I get the following error:
com.sap.ip.mi.admin.core.ApplicationException: Connection couldn't be recreated: 1 cause: Encountered invalid managed connection, last cause Couldn't execute interaction. 2 cause: Couldn't execute interaction.
I can see the list of devices, but if I mark one, I don´t get the details of it. What could be the cause?
Cheers,
Thorsten

update on above reply-;
Find the comlete list of authorization listed below-:
S_RFC                                ACTVT
SDIFRUNTIME
SYST
SGOO
SRFC
SYSU
SYSO
MEMGMT*
MEREP_INSTTK_MPC
MEREP_JAVACLIENT
ME_CENTRAL_TRACING
BWAF_MW
BWAF_MOMO
BAPT
BWAF_INSTALLATION
MI_PACKAGE_GEN
ME_MON_SHLP
ME_QUEUE_MON
ME_TECH_MON
RFC2
SDDO
TCD
DEVICE_CONFIG S_MOMO
S_MI_MGMT
MI_GROUP
S_USER_GROUP
ME_CONFIG_INFO
ME_USER
RFC1
S_RFC_ADM

Similar Messages

Error in Mobile Administrator

Hi,
on our Webas 6.40 SP18, I have configured the Mobile Administrator, according to the MI Installation Guide. When I access "

problem handled in different thread
Message was edited by:
Thorsten Gerhart

HT1926 When trying to install iTunes, I'm getting the following error "Apple Mobile Device failed to start. Verify that you have sufficient privileges to start system services". How do I fix this?

When trying to install iTunes, I'm getting the following error "Apple Mobile Device failed to start. Verify that you have sufficient privileges to start system services". How do I fix this?

SAME EXACT PROBLEM! SO FRUSTRATED AND ****** OFF!

Devices not showing up in client software Administration section

None of our devices are showing in the "devices" portion of the administration section in the client app.
Everything is functioning fine and I can administer devices through SysPrefs, but will eventually need to get back to this setup to add "edit in place" volumes, etc. I've tried refreshing, creating a new device to refresh list and many other things. I can't even search for a device by name in the "devices" section. Again, this is the only place where I can't see them.
Any ideas? Need it back bad!
Ryan

Hey!
Correct, not seeing any devices, but ONLY in the "devices" portion of the client admin. I see all my devices everywhere else and the entire system is functional, except for the fact that I can't get to them through the client admin. I can access it through the Sys Prefs portion of FCS, but need to get into the client admin for "edit in place", etc...
I do have backups from as far as 6 months ago, however - Much has changed on the server and I'd had to have to revert to one of those. Not sure exactly when this issue started, but I've seen it for at least a month.

HT1926 I can't re install iTunes because I get a error saying mobile device could not start.

I can't re-install iTunes because i get an error saying Mobile Device could not start?

Same here TC, very annoying

I am trying to sync my iphone and im getting and error "apple mobile device service not started"

I am trying to syn my iphone and im getting an error "apple mobile device service is not started" what do i do?

See if this page helps you restart it, it also has instructions for setting it to start automatically : http://support.apple.com/kb/TS1567

Device Maintenance - Config Files

Hi all,
I 'm playing a bit around in the SAP Netweaver Admin. it 's the first time I 'm using it for MAM maintenance.
In the 'Device Maintenance' page (Administration > Mobile Infrastructure) you can select a device and you should be able to watch the config files ('Config Files' tab).
I can in fact see 2 types of config files: listOfJars.txt and startup.bat.
But how can I watch / edit these files via Netweaver Admin? I can click on them, but nothing happens. And at the bottom of the page I can see the text 'Download File', but it's only plain text, no link...
Thanks for your feedback!
Best regards,
Diederik

Never mind...
It seems to be a config issue, cause it 's not working in test environment, but it is working in production environment...
Thanks anyway!

IPMA Assistant Console: âSystem Error: Please contact Administratorâ

Version of CCM used 4.1(3)sr2
I have setup a 2:1 (manager (lukes & hans) : assistant(leiao)) IPMA shared line config for the first time (successfully setup 1:1 shared line configs before) and once the assistant loads IPMA Assistant Console (IPMA AC) on PC1, enters her IPMA AC credentials, click OK the assistant gets the following error message âSystem Error: Please contact Administratorâ. I can confirm that IPMA AC works on PC1 (XP Pro SP2 Windows FW disabled) as other 1:1 assistants can log into IPMA AC successfully. leiao also gets the same message when she logs into PC2 (XP Pro SP2 Windows FW disabled) and PC3 (XP Pro SP2 Windows FW disabled ) that have IPMA AC installed. From a telephony point of view all IPMA setups (1:1 & 2:1) work as expected its just IPMA AC doesn't work for 2:1 IPMA shared line setups.
I have deleted lukes, hans and leiao device user profile and user profile, restarted the Tomcat IPMA service and re-created the profiles and still the same problem. In desperation I have even rebooted the CCM Pub & Sub and still leiao gets the message above.
lukes
8001 - External DDI
1001 - Internal Ext
3001 - Intercom
Hans
8002 - External DDI
1002 - Internal Ext
3002 - Intercom
Leiao
8003 - External DDI
8002 - hans
8001 - leiao
3003 - Intercom
I have noticed looking at the IPMA Service trace logs on CCM that CCM recognises leiao user as a ProxyLineAssistant instead of a SharedLineAssistant like all other 1:1 assistants?? I setup the managers and assistants in the 2:1 config the same as 1:1 shared line config but CCM appears to think that leiao is a ProxyLineAssistant??
Does anyone have any hints or tips on how to solve this, any further info required please let me know :-)
Thanks for your assistance :-)
Kind regards
Anthony.

delete the old assistant (DWAssist). Remove it from the manager's IPMA configuration and substitute it with a new assistant (DWAssist1). After reconfiguring IPMA accordingly, restart tomcat services

WM: Error occurred during storage section search (FGWM05 001)

HI friends
              i done GRN 101(movement type) with mb31 for production order ..based on TR Iam trying to create transfer order i have
the below error. where i missed the configuration
"Error occurred during storage section search (FGWM05 001)"
    Message no. L3 041
Diagnosis
    No storage area search has been defined for this material and this
    storage type.
Procedure
    Contact your system administrator! Note down the material and the
    storage type listed within parentheses in the error message.
with regards
dinesh
Edited by: code acess on Jun 28, 2011 8:30 AM

Hi
In WM customizing Please check for your warehouse/Storage type combnation the storage section search is on and valid.
IMG>Logistics Execution>WM>Strategies>Storage section search
if there is no entry then maintain it. The nest error may be storage bin. Make sure that you create storage bin for whsno/storage type/storage section combination by using LS10 or LS01N)
Hope it helps
Karthik

Mobile Administrator in SAP NetWeaver Mobile 7.1

Hi All
I want to log in into the SAP NetWeaver Mobile Administrator in 7.1.
In the help of sap, it says:
You can access the SAP NetWeaver Mobile Administrator through the DOE. To do this, you must log on to the DOE and choose Data Orchestration Engine > Data Orchestration Admin and Monitoring Portal.
But there is no such link in my SAP screen.
What are the various ways to access SAP NetWeaver Mobile Administrator in 7.1?
Waiting for your replies.
Ankur

Hi Ankur,
you can also directly navigate to the mobile administrator using the web browser. The url is as follows:
http://host:port/sap/bc/webdynpro/sap/sdoe_administration?sap-language=EN
Host and port you have to adjust to your settings. These are the same settings you are using during synchronization on a client device.
Regards,
Stefan

Setup synchronize with address for Sage ACT! showed Runtime Error: Cannot configure the section.

Hello Blackberry Senbai...
As my problem showed as subject line. "When I setup synchronize with address book for Sage ACT! showed Runtime Error: Cannot configure the section."
Setup was stopped from this point.
my system info..
Desktop Manager version is 5.0 downloaded from Blackberry website.
ACT version is 2010.
OS: Window XP Pro with service pack 3
Thank you for your time to review my problem.

Hi and Welcome to the Forums!
Since the version of ACT that you state is not contained in the PIM compatibility matrix, I'm not sure that there is anything to be offerred...
KB12268 Applications supported by BlackBerry Desktop Manager for synchronization
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Problem in MI 7.0 Mobile Administrator

Hi,
I was configuring MI 7.0 in NW 7.0 SP09. But the Mobile Administrator application is not at all running. It is showing error message "Connection can not be recreated". I navigated to the Web Dynpro Content Administrator and found that all the applications under sap.com/tcmobileadmin~ui
referencing to sap.com/tcmobileadminea which having status RED. But sap.com/tcmobileadminea in Visual Administrator is running.
Other links in Mobile Administrator showing error "Can not start plug in" .
Can anyone suggest me what may be the problem?
Thanks & Regards,
Subhayu De Sarkar

Dear Subhayu,
This post is common to both of your related threads.
First of all, you have not answered my question of not having a server with latest patches. If it was a new server, you could have started off with NW 7.0 SR3 setup (which gives you SP 14 by default) and then apply the rest of the packages.
Find below my answers to your questions:
1. If I follow the template based configuration then the JCO-RFC provider name differs with the document.
A: Yes they might differ. Configuration, if done the manual way, does not need the use of template, but initially if chose, the template would have saved a lot of your time.
2. The document suggests that the JCO Destinations should be created using the MI Admin Service user. But that user is not allowd to create JCO Destination. It is having access problem.
A: Generally, I give the j2ee_admin (ABAP) role to the MI admin and the mobile super admin, additional admin roles similar to j2ee_admin (UME) to the MI admin, since generally, the MI admin is the j2ee admin too.
3. The document suggests to use MI Admin Service user in CIM Client Generation is SLD Supplier service in VA. But this user is not allowed to be used as SLD Service provider.
A: I have used the user j2ee_admin for the same in all my MI installations
4. The template based MI configuration can not register RFC destination. By default it takes the DDIC user for the it but DDIC does not have access to maintain the MEMGMT_J2EE_DEST table.
A: Use manual/template based, dont use both. As a note, the template configs will supersede the manual configs. You can use an admin user, who is having the ABAP roles SAP_MI_ADMIN and J2EE_ADMIN
Regards,
Veera

Is MI WebConsole and NetWeaver Administrator- Mobile Administrator SAME ?

Hi
I am trying to access MI - WebConsole but could not make it.
I have SAP Web AS 7.0 with MI 2.5 installed with latest service packs. After all configuration (SAP MI 2.5 SP17 Standard install/config guide), I could not get SAP MI WebConsole. Getting 404 error.
After reading few documents I have an assumption/suspection that
MI WebConsole is for SAP Web AS 6.4 and
NetWeaver Administrator -> Mobile Administrator for SAP Web AS 7.0
to do the same functionality.
So the question is...
is MI WebConsole (http://<server:port>/me/WebConsole/login
will not work in SAP Web AS 7.0 as it has been replaced by NetWeaver Administrator -> Mobile Administration ?
(http://<server:port>/nwa
If not, do we still need MI WebConsole inorder to make communication between R/3 (ABAP stack) and MI 2.5 Client(laptop)
Even http://<server>:50100/me is not working. Always getting 404 Error.
I have http and https configured successfully.
Please advice.
Here is my system landscape for the reference:
SAP MI 2.5 (middleware) -> installed in a separate server with ABAB+JAVA stack and SAP Web AS 7.0.
SAP ERP 2005 (backend) -> installed in a separate server with ABAB stack only and SAP Web AS 6.40
SAP MI 2.5 (client) -> installed in a laptop with Windows XP Pro.

hello sri,
java sync servlet and MI WebConsole will still be supported
for awhile when the Mobile NWA gets matured...
MI WebConsole is only an administration tool, the MI Sync
Servlet is the one responsible for data transfers from
your MI client to MW. In 7.0, the Mobile NWA will become
the primary tool instead of the MI WebConsole and java
sync servlet will also be substituted by the ABAP sync
service. you can easily configure you MI using templates.
your errors might be some configuration problems.
try tracing for exceptions in your J2EE visual admin.
regards
jo

We have two users that have been using Creative Cloud for almost a year. Recently, sometime in the last 4ish weeks, the users can no longer run Creative Cloud apps. (Yes, our subscription is paid.) Error simply says administrator access is required

We have two users that have been using Creative Cloud for almost a year. Recently, sometime in the last 4ish weeks, the users can no longer run Creative Cloud apps. (Yes, our subscription is paid.) Error simply says administrator access is required to install. The apps have already been installed. The users cannot run them unless they are in the local admin group.Using "Run as admin" does not work. It gives the same error.
I have opened a case with adobe support and was basically told to suck it up and put the users in the admin group. Actually, what was said was that it is "mandated that the users have administrative rights".
There are a couple of things wrong with this. It was working for both users until recently - a recent required creative cloud update. The users have never been local admins yet the apps were working (poorly, but working).
We are in an enterprise environment and users simply do not have administrative rights on the computers.
I have changed permissions on all adobe folders, granting users or authenticated users modify or full control rights, did the same in whatever Adobe registry HKLM keys I could find. Nothing has allowed the users to run the apps - unless they are put in the local admin group.
Someone has to have a fix for this. Adobe apps have proved to have far too many vunerabilities to even entertain the idea of elevating user rights. I can't imagine that enterprise environments are allowing this.
Any help or suggestions are greatly appreciated.

Jeff,
Thank you for your response. The users in question are "standard" domain users. We do not reduce users permissions below the standard level.
The apps do not load with their current standard user permissions.
The thing that makes this odd, is that up until recently they did this issue with cloud apps. The only way I can make it work for them now is to put them in the local administrator group on their pc's - which is not going to happen.
This is what they now see. As I said before, this was not a problem up until recently they would see all their available apps. If I put them in the local admin group the apps are listed without having to install. Everything is there, just not accessible to the user.

I plugged in my ipod and now i get the error message: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled" - i have a MAcBook pro and now my USB ports do not work - can anyone help me ???

i plugged in my ipod and now i get the error message: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled" - i have a MAcBook pro and now my USB ports do not work - can anyone help me ???

Sometimes you have to reset the SMC two or three times for it to work, don't know why. I've seen that error message before and 100% of the time it was fixed with an SMC reset. I suppose it's possible that your keyboard or mouse IS drawing too much power, do you have access to another you could try?

Error in Mobile Administrator, section device maintenance

Similar Messages

Maybe you are looking for