Failed 4.1 software upgrade

Hello, I have upgraded my software in iTunes to the latest version. None of the 4.1 software features have been added onto my phone and it's extremely slow now. I have a 3GS and it's only half a year old. I have tried restoring the phone but the speed is still really slow. I don't care about the new features that the upgrade is supposed to give you, I just want a fast running phone again!

major update 4.1 included in for 3gs is the 'game center'
and you did not mentioned your earlier version.
regarding slow perfomance try restarting your phone

Similar Messages

Help needed: iPhone 4 software upgrade failed many times

Hello. I've bought an iPhone 4, which its operating system is 4.3, and was prompt by iTunes about this iPhone 4 software upgrade to iOS 4.3.5. I've downloaded the software and waiting for quite some time and after the dowloading has completed, the file will be processed. After processing, there is a popup saying that somehow the software upgrade failed and said something like make sure that your connection is correct etc. Do you have any idea on how to solve this issue?
Help me, please. Thank you very much.

This is asked and answered many times each day. The forum search bar is on the right side of this page.
Diasble your firewall/security software and try again.

Failed Software Upgrade

Have a customer that reports a 4402 controller that has no console access after a software upgrade from 4.2.99 to 4.2.176.
They report they thought 4.2.176 went in ok but failed to read the configuration.
So they loaded 4.2.112.0 ER.aes.
The controller powers up but no console access. Service port interface lights up but does not lease an address in DHCP.
From the look of the hyperterm log (before console was lost) both the primary and secondary were loaded with the same image version. But this failed it also appears the tftp load failed.
Is the controller bricked at this point?

are you using tftpd32 or similar as your tftp server - the newer wlc software revs are greater than 32MB. had a similar problem to you until i started using tftpd32 as my tftp server - see url:
http://www.cisco.com/application/pdf/paws/68835/wlc_upgrade.pdf

I have lost AirPlay and sharing with my PC since accepting a software upgrade to the TV yesterday. I have tried restoring and reinstalling this software but this failed to solve the problem. Any suggestions would be very welcome.

I have lost AirPlay (with iPad and iPod touch (new) both on os5 ) and sharing with my PC (uptodate iTunes) since accepting a software upgrade to the Apple TV yesterday. I have tried restoring and reinstalling this software but this failed to solve the problem. Any suggestions would be very welcome.

IEP1 wrote:
I have lost AirPlay (with iPad and iPod touch (new) both on os5 ) and sharing with my PC (uptodate iTunes)
Check your Windows settings along this contribution from Chrism0:
https://discussions.apple.com/message/16568477#16568477
Also check that the ports 5353 and 5354 (Bonjour (mDNSResponder), AirPlay, Home Sharing, Printer Discovery) are open on Windows Firewall.
Lupunus

CSS software upgrade failed

Hi everyone,
My customer had a problem during upgrading CSS software from 7.50.303 to 8.10.602.
He executed upgrade but it was failed with the following message.
==========
CSS# upgrade "sg0810602.adi-gz"
CSS#
Current Version: sg0750303 OFFICIAL
*** You must remove an installed version to upgrade. ***
Cannot delete enough installed versions to allow the upgrade.
One cannot delete an image that is the currently running image,
or an image that is selected as the primary or secondary boot
image. You must de-select the primary or secondary image
in order to continue with this upgrade.
==========
There is no another information on the CSS but I have just the above message.
Have you experienced similar symptom? or Do you have any information why this is happened and/or how can resolve this problem?
Your information would be appreciated.
Best regards,
Shinichi

Hi Shinichi,
Can you please share the commands you have run for upgrading the CSS software.
Kindly tell how many versions are already installed on you CSS.
Use the version command to see the currently running software version.
To
a. List the ADIs on the CSS.
(config)# show installed-software
sg0720104
sg0730003
b. Access boot mode:
(config)# boot
(config-boot)#
c. Use the remove command to remove the ADI.
(config-boot)# remove sg0720104
If you are having two software version installed.
Kindly send me the output of the
(config)# show installed-software
Before you can upgrade your CSS, make sure you have enough space on the box to
complete the upgrade.
Because a hard-disk-based CSS can contain a maximum of four ArrowPoint Distribution
Images (ADIs). A Flash disk-based CSS (CSS 11150 or CSS 11800) can contain a
maximum of two ADIs. If the limit has been reached, you must remove one ADI
version before you can add a new version.
====================================
Before you can upgrade your CSS, you must copy the new CSS software to your FTP server and configure an FTP server record so the CSS recognizes the server. Use the show installed-software version-limit command to display the maximum number of installed versions allowed on your hard disk or Flash disk.
When upgrading the CSS software, you can use the upgrade script or manually enter CLI commands. The upgrade script allows you to upgrade the CSS either automatically or interactively by responding to script prompts.
Either way, the tasks that the script performs include:
•Checking to see how many installed software versions are installed on the CSS, and if the CSS contains the maximum number of installed software versions, then deleting an older software version.
•Archiving the running configuration to the startup configuration.
•Copying the new ADI to the CSS boot-image directory.
•Unpacking the new ADI.
•Copying the scripts and user profiles from the older CSS software to the new software. The copied scripts do not include Cisco-supplied scripts except default-profile.
•Setting the primary boot file to the new ADI.
•Rebooting the CSS.
We recommend that you use the upgrade script because the upgrade script ensures that the existing scripts and user profiles are copied to the new software.
When manually upgrading the CSS software, you must enter CLI commands to perform the same tasks that the upgrade script would perform.
You can run the upgrade script to perform the software upgrade without having to enter any information. The script automatically:
•Checks to see how many installed software versions are installed on the CSS. If the CSS contains the maximum number of installed software versions, the script deletes an older version.
Note The script does not prompt you to delete a version of software that you configured as the primary or secondary boot file. On a disk-based system, you may need to quit and then deselect the primary or secondary boot file before continuing with the upgrade.
•Archives the running configuration to the startup configuration.
•Copies the new ADI to the CSS boot-image directory.
•Unpacks the new ADI.
•Copies the scripts and user profiles from the older CSS software to the new software. The copied scripts do not include Cisco-supplied scripts except default-profile.
•Sets the primary boot file to the new ADI.
•Reboots the CSS.
Kindly Use the following URL for your reading if you have not gone through this:
http://ciscosystems.com/en/US/docs/app_ntwk_services/data_center_app_services/css11500series/v8.20/configuration/administration/guide/Upgrade.html
Please revert back with the answers of my question and I believe we will be able to resolve your problem.
Best regards,
Sachin

E71 firmware upgrade failed and mobile software co...

I recently purchased a new E71 and on the same day I run the "Phone software upgrade". It took around 2-3 hours to download and upgrade the phone. I saw it was updating to 3.x framework from 2.x.
When I see after 2-3 hours what I saw that screen was blank, nothing on screen and keyboard light was on. I restared by removing the battery and restarted, but nothing happened. But on my PC upgrade was successful.
How this is possible. Is the framework upgrade is this much critical ? OR is there any other way around to upgrade the framwork of the phone?
After this problem I submitted my phone to nokia care and they installed the framework again, because it was corrupted. Now I want to upgrade the framework, so please let me know how can i do this easily.

Have a look at the link below for details on how to update your firmware. It is probably the same as the procedure you used the last time.
http://europe.nokia.com/get-support-and-software/download-software/device-software-update

3502I access point unsuccessful software upgrade

Hi all. I have a trouble with AIR-CAP3502I-R-K9 AP and I want to ask help.
I tried to upgrade IOS software in ap because it was connecting and disconnecting to controller too often. I already upgraded one of two access point and it working stable at this time, but the second one not.
I tried to make software upgrade:
ap: set IP_ADDR 192.168.100.100
ap: set NETMASK 255.255.255.0
ap: set DEFAULT_ROUTER 192.168.100.1
ap: tftp_init
ap: ether_init
ap: flash_init
ap: tar -xtract tftp://192.168.100.101/ap3g1-k9w8-xx.152-2.JB.tar flash:
After that software was donwloaded to ap and self-extracted.
And when I'm trying to boot ap after upgrade I see such messages:
C3500 Boot Loader (AP3G1-BOOT-M), Version 12.4 [mpleso-ap_jmr3_esc_0514 125]
compiled Fri 17-Aug-12 12:12 by mpleso
******** AUTOMATIC DDR CALIBRATION UPGRADE LOGIC *********
=== 1. Is original FCS bootloader in BS:? If not, skip upgrade ===
    ---> original FCS bootloader not detected -- skip upgrade
ap: set IP_ADDR 10.33.9.240
ap: set NETMASK 255.255.255.0
ap: set DEFAULT_ROUTER 10.33.9.1
ap: tftp_init
Unknown cmd: tftp_init
So, I even can't load new software. What can I do now?
Any help much appreciated.

ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...
r WRDTR,CLKTR: 0x8200083f 0x40000000
r RQDC ,RFDC : 0x80000032 0x00000211
using eeprom values
WRDTR,CLKTR: 0x8200083f 0x40000000
RQDC ,RFDC : 0x80000032 0x00000211
using SMSJ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000032, 0x00000211
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 51 files, 13 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 11743232
flashfs[0]: Bytes available: 19996672
flashfs[0]: flashfs fsck took 10 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 30:f7:0d:7c:44:c8
Ethernet speed is 100 Mb - FULL duplex
Loading "ap3g1-k9w8-mx.152-2.JB"...ap3g1-k9w8-mx.152-2.JB: permission denied
Error loading "ap3g1-k9w8-mx.152-2.JB"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/ap3g1-k9w8-mx.152-2.JB/ap3g1-k9w8-mx.152-2.JB"...################
File "flash:/ap3g1-k9w8-mx.152-2.JB/ap3g1-k9w8-mx.152-2.JB" uncompressed and installed, entry point: 0x4000
executing...
enet halted
IOS Secondary Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x8200083f, 0x40000000
RQDC, RFDC : 0x80000032, 0x00000211
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 51 files, 13 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 11743232
flashfs[0]: Bytes available: 19996672
flashfs[0]: flashfs fsck took 10 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 30:f7:0d:7c:44:c8
Creating Test Kernel diagnostic commands
Radio 0 : Vendor 0x11AB, Device 0x8324
Radio 1 : Vendor 0x11AB, Device 0x8350
Radio 2 : Vendor 0xB556, Device 0x7CF2
Radio 3 : Vendor 0xC277, Device 0xFFF5
******** AUTOMATIC DDR CALIBRATION UPGRADE LOGIC *********
=== 1. Is original FCS bootloader in BS:? If not, skip upgrade ===
    ---> original FCS bootloader not detected -- skip upgrade
Boot CMD: 'boot ap3g1-k9w8-mx.152-2.JB;flash:/ap3g1-k9w8-xx.152-2.JB/ap3g1-k9w8-mx.152-2.JB'
Loading "ap3g1-k9w8-mx.152-2.JB"...ap3g1-k9w8-mx.152-2.JB: permission denied
Error loading "ap3g1-k9w8-mx.152-2.JB"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/ap3g1-k9w8-xx.152-2.JB/ap3g1-k9w8-mx.152-2.JB"...flash:/ap3g1-k9w8-xx.152-2.JB/ap3g1-k9w8-mx.152-2.JB: no such file or directory
Error loading "flash:/ap3g1-k9w8-xx.152-2.JB/ap3g1-k9w8-mx.152-2.JB"
Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
C3500 Boot Loader (AP3G1-BOOT-M), Version 12.4 [mpleso-ap_jmr3_esc_0514 125]
compiled Fri 17-Aug-12 12:12 by mpleso
******** AUTOMATIC DDR CALIBRATION UPGRADE LOGIC *********
=== 1. Is original FCS bootloader in BS:? If not, skip upgrade ===
    ---> original FCS bootloader not detected -- skip upgrade
ap:

Can't install software upgrade to iTouch with 1.1.4.

I recently acquired an 16 GB iTouch that already had version 1.1.4, and I purchased the January 1.1.4 software upgrade to get email, etc.
I can see the purchase for the upgrade in my account, but it won't install the upgrade to my iTouch because of an unknown error OxE8000001. I restored the iTouch, but that didn't help. Every time I sync, I get the same error message.
Can anyone help with this?
I have read the help notes on the website; I'm on the home computer I normally sync on, I have iTunes 7.6, etc.

Well, I was hesitant to do that, since all the Apple info on the web said that you had to be logged into the account in which you purchase the software upgrade.
However, I found some additional info at this website: http://www.apple.com/support/ipodtouch/troubleshooting/ipodtouch/#
It suggested that if all else failed, try: Tap Settings > General > Reset > Erase All Contents and Settings
When I did that and restarted and sync'd, it finally downloaded by software upgrade!! Hooray! It only took me about 5 hours to accomplish this! Thanks for your help, Scott!

How do you put previously bought software upgrades on replacement ipod?

Back in July I bought the 2.0 software upgrade for my iPod. Just a few days ago I sent my iPod in for WiFi problems, and just got my replacement today. How do I put the 2.0 software upgrade on this new iPod?

Hi fraxh,
Welcome to Apple Discussions.
If you've bought the update from the the iTunes Music Store you should be re-purchase it, that failing click the "restore" button on the iPod Touch summary page, as it may have the update archived, in which case it should re-install.
Regards,
Peter.

Down-loading software upgrades is being limited by "server timed out"

My broadband connection is of modest speed as I live many miles from the Telephone Exchange. When I attempt to download Apple software upgrades, say of 50 mb, I get cut off after about 12 mb with a message" sever timed out code -1001". When I make a second attempt, I have to start again "at the beginning" rather than continue at the point where the last attempt failed.
Grateful for any advice (apart from being told to move house nearer the Telephone Exchange!) I am only just computer literate.
regards

Hi,
Make sure that the software while upgrading and downgrading was from your service providers official site. If not, go to the following link :
http://in.blackberry.com/support/apps-and-software/desktop-and-device-download-sites.html
Now, if you have already upgraded and downgraded the software, and tried battery pulls. The only problem that i can think of for browser time out's could be with the service books.
Open the link and follow the instructions:
http://btsc.webapps.blackberry.com/btsc/viewdocument.do;jsessionid=FAA7D6BA303A725FD73A92C596891272?...
If your query is resolved then please click on - 'Accept as Solution'
Thank You.

Software upgrade assistant launches IE

Please help! Everytime I plug my phone into my computer, the Verizon Software Upgrade Assistant starts Microsoft's Internet Explorer and loads a verizon web page. I can't find any way to stop this from happening. I don't use IE because it's too great a security risk. I don't appreciate Verizon malware loading this program without my permission. I also don't need and don't want to see Verizon's web page everytime I plug in my phone. I tried removing the Software Upgrade Assistant, but then I get the "Software available for your phone" pop-up instead. How can I prevent my system from starting IE everytime I plug in my phone?

Bearone21,
      Thanks for your message. My PC still connects to the internet
just fine, but everytime I plug the phone into the USB port, the new
software launches Internet Explorer (on the PC) and loads Verizon's
Consumer Products web page. There are two problems with that. First, I
don't use Internet Explorer because of it's inherent security risks and
I don't want it running on my machine. Second, I don't care to be
spammed with the Verizon Consumer Products page every time I plug my
phone in to sync it or charge it (several times a day). I was hoping
there was an option to turn this "feature" off. A simple options menu
box that would let me choose between "on connect launch browser." and
"on connect do nothing" would be sufficient. I've reviewed all the
options and this choice doesn't appear to be available, hence my question.
      Note that this never happened until I did the 4.3 upgrade, so I
have to assume it is another one of the several defects in the upgrade
package. There are a couple of simple ways to fix this defect. The
first, and best way, is for the software to give me the option to
launch, or not launch Verizon's consumer products web page on USB
connect. That would solve the problem completely. Failing that, the
Verizon software should use the system default browser instead of
launching IE. That might still be annoying, but at least it would
resolve the security problem.
      I appreciate your response to my inquiry and hope that Verizon and
Samsung will continue working together to fix the many problems with the
4.3 upgrade. Hopefully Verizon will recognize that the browser market
has changed and IE users account for less than 23% of the browser market
today (see http://en.wikipedia.org/wiki/Browser_wars). Verizon needs to
adapt to the new browser climate and stop writing software that is
dependent on IE.
               Thanks again,
Dave *
>>Personal information removed to comply with the Verizon Wireless Terms of Service<<
Message was edited by: Verizon Moderator

Msi X320 not recognizing hdd..after software upgrade

Well i got this like new x320 that was given to me after a failed software upgrade...it no longer shows any hard drive present...i have changed the hdd thinking that could be the problem...still shows nothing...can it be a corrupted bios?...or did somehow the software upgrade remove the info....any help will be greatly appreciated..trying to make this work for my mother's birthday....God Bless John

Well this is long out of warranty...i did not think of the F3...thank you i will try that....God Bless really appreciate it...John....i got this second hand and i think they tried to upgrade the software...it does not show any hdd...no matter if i change it or not...i thought about using a hdd thru a usb...i will try and let you know what i find out...

Data deleted after software upgrade

Help! I connected my iphone 3 into itunes and accepted the software upgrade on offer. I now have lost ALL data incuding precious photos. Don't care about message threads or settings, but I do care about photos. I have imported my contacts back in from my SIM card but am at a loss as to how this happened when I just selected the standard prompts to update software. I am using another PC as my regular PC is not working, so cannot get photos off that from my last syncing. Thanks

Well, some info:
Apple assumes that all photos in the Photo Library you also have on your computer and thus it's no problem if the sync/update process deletes them, because you can re-sync them from your computer just like you did in the first place. This is true of all photos, video, music, which Apple calls "media". The iPhone is NOT a backup.
Syncing with a new computer offers a warning that it is going to delete all media from the phone and replace it with media from the new computer, at which point you should have canceled. You are only allowed to sync media from one computer at a time.
Syncing with a new computer should have backed up your phone first, and that would include the photos in the Camera Roll, that you took with the phone; but NOT the photos in the Photo Library, that you synced to the phone. The backup should also include data saved within apps. So you might be able to Restore from Backup to get some stuff back, or use a third-party utility to pull your Camera Roll photos from the backup file on the computer. Assuming iTunes backed up first.
Failing that, I don't think I've heard of any way to undo loss of media due to syncing with a new computer. You might ask google.

ASA5510-BUN-K9 software upgrade from 7.0(4)12 ??

I just purchased this firewall from govconnection.com and wondering about software upgrades. It has above ASA version software and ASDM 5.0(4) software.
It appears I need to somehow attain PICA and verification keys and whatnot - I've inquired with my seller to see if they can provide that -
but also curious if the newer version of software is desireable enough to jump through all these hoops? Or perhaps I'm missing some simpler method of updating software on this unit?

Hi,
Basically, if you just buy an ASA (or any Cisco box) without purchasing any support then you get what's called "warranty", which entitles you (usually) to 90 days of hardware support and software maintenance updates.
Unlike IOS, it's not too well documented what qualifies as a maintenance update on ASA but it's probably only the latest build of 7.0(4) if your box came with 7.0(4). Within 90 days the hardware replacement SLA is 10 days - after 90 days it's time & materials at Cisco's discretion.
The point I'm trying to make is that Cisco's warranty is rubbish - you're more or less forced into buying smartnet whether you like it or not (unless you're in the habit of discarding failed hardware and simply replacing with a handy spare..)
That said, smartnet has fantastic value, as follows:
1) new hardware delivered with or without an engineer (up to 24x7x2)
2) a license to install any and all software updates (for your purchased feature set)
3) Access to the TAC 24x7
Here's the full list:
http://www.cisco.com/application/pdf/en/us/guest/products/ps2978/c1592/cdccont_0900aecd8042b4d6.pdf
So, whenever you buy Cisco kit you should always be thinking about buying a smartnet contract (there are separate services to cover IPS devices, and software-only products like callmanager) unless you only want it for 90 days and you don't care about the 10 day warranty replacement SLA.
Finally, if you really don't want the hardware support, but you do want the software, then you can simply purchase the particular version you want for a one-off payment (but it won't be very cost-effective if you upgrade a lot - and a years smartnet contract might even be cheaper..)
HTH - plz rate if useful.
Andrew.

BlackBerry Pearl 9105 track pad fault following software upgrade

Since 22 Feb 2015 track pad and buttons like camera no longer work within most applications. Seems to be directly related to faulty automatic software upgrade that so many users are complaining about. Track pad works for 10 minutes after each hard reset, then stops working again. Please can BlackBerry resolve urgently, as phone is now practically useless.

Okay. So not an OS upgrade. Sounds like you are talking about BlackBerry Protect and it is set to perform a backup on a weekly interval. Or else you are connecting to the Desktop Software and it is set to perform a backup weekly.
It is likely the problems occurring around the time of a backup is coincidence. Not saying 100% it isn't somehow related to something you did, just it probably didn't happen because of a backup.
So here are some thoughts: The trackpad starts working again after a hard reset. Again, there could be more involved, but this fact suggests it is possible the issue could be software. Here is what I would do.
1) Do a full backup.
2) Do a clean OS reinstall. See http://www.blackberry.com/btsc/KB11320
3) Perform the setup and log in with Blackberry ID as necessary. Do not restore backup. Do not install add-on or third-party apps.
4) Test for a while, for an hour or so if possible. Hopefully there is no problem. If there is, try a hard reset and see if that corrects the problem. It isn't good news if the problem still occurs and is corrected with a hard reset, but it may be useful information to a technician.
5) Assuming there is no problem in step 4, restore the backup. Again, test for a while. Launch apps, browse around in device settings, put the device through paces. Hopefully there is no problem. If there is, then it's a reasonable suspicion that the problem is associated with corrupt data or settings in the backup. So, if there are problems in this step, do a security wipe and do a selective restore and restore personal data such as address book and calendar, but not settings and customizations. Test again.
6) Install apps, most needed first, one at a time. Test before installing the next app. If you have the problems after installing the app, delete the app and test.
Good luck. Recognize that it is very possible the track pad and buttons are failing or have failed. I'm sure repairs can be made, but I'm not one to best advise on that. There are DIY videos and so forth on the Web, and some parts vendors provide instructions. Another option is to find a shop and get a diagnosis and estimate, provided the cost is reasonable.
- Ira

Failed 4.1 software upgrade

Similar Messages

Maybe you are looking for