Macbook Pro Frozen upon start up

Hi There,
I am hoping someone may help with a frozen screen. First I am not very technical, so bear with me. I am also new to the Mac World.
Yesterday I was using network diagnostics to determine why I could not get online (turns out it was a provider problem). During the diagnostics I attempted to quit it, with no success. At that point I powered the machine off, because I did not want to continue (I know very stupid).
When I attempted to restart, it began normally with starting OS X and the gray gear wheel spinning. The gear wheel stopped spinning and up popped a blue screen. It never asked me to sign in, just skipped to the blue screen. My mouse pointer still works, but nothing else exists on the blue screen.
I than tried resetting the original settings by removing the power adapter, battery and holdng down the power button for atleast 5 seconds. No luck.
I also installed the start up disk and ran first aid. It came back no repairs needed. I assume I ran it properly. I asked it to scan the hard drive for needed repairs.
I anticipate having to reinstall start up disk 1 to correct the problem. However, I have not recently backed up (again dumb), and now without the ability to boot the hard drive I can not backup; or atleast I have no idea how to at this point.
Anyone have any ideas? Thanks for any help you can offer.
macbook pro Mac OS X (10.4.6)

Hi, dbrian. Welcome to the Discussions.
1. You wrote: "I also installed the start up disk and ran first aid. It came back no repairs needed. I assume I ran it properly. I asked it to scan the hard drive for needed repairs."To verify if you performed the steps properly, and to add some additional steps that may help, run the procedure specified in my "Resolving Disk, Permission, and Cache Corruption" FAQ. Perform the steps therein in the order specified.
2. An errant Startup or Login Item maybe the cause. My "Troubleshooting Startup and Login Items" FAQ can help you pin that down if such an item is causing the problem.
3. To rule out the possibility that the initial hang when quitting Network Diagnostics was not hardware related, run the Apple Hardware Test that came with the computer. See my "Apple Hardware Test" FAQ for comprehensive advice on using the Apple Hardware Test in troubleshooting, including running the test in Loop Mode.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X
Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
I may receive some form of compensation, financial or otherwise, from my recommendation or link.

Similar Messages

Macbook pro frozen at start up?

it's just frozen at the apple logo during start up...
here's how this started:
itunes froze, so i tried to forcequit. nothing happened--the whole thing was frozen. so i manually pressed the power key and held it down. let it sit for a while. then i turned it back on. it's stuck at the opening apple logo with the white background now for like 20 min. i tried the same thing again--with the same results (i.e. holding power button down.). then i came back and found a bar partially loaded at the bottom of the screen with teh apple logo, and it's just frozen there.
this time while i let it sit to load, it shut off by itself...
please help!!

Do you have another drive you can boot from? If not start from your Mac OS X Install disc: Insert the installation disc, then restart the computer while holding the C key.
When your computer finishes starting up select your language.
Important: Do not click Continue in the first screen of the Installer.
Choose Disk Utility from the Utilities menu and run "Repair Disk"
Note any errors.
Then, go to /Library/Startup Items and move whatever is there to your desktop. Nothing is installed in that folder so anything in there was put in by you. Now restart normally.
-mj

My MacBook pro won't start. It is frozen on the gray screen with the apple. Please help?

My MacBook pro won't start. It's stuck on the gray screen with the apple logo.

Reinstall OS X:
Reinstall Snow Leopard without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
Reinstalling Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

TS3423 17" macbook pro won't start blue file with question mark is all that appears on the screen

My old macbook pro will not start up. Worked fine yesterday, today all I gat is the startup sound and a blank blue screen. After a while the screen shows a file folder icon with a question mark in it. Any ideas

Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by:
Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
Boot drive's directory has been corrupted - Repair with Disk Utility.
Critical system files are damaged or deleted - Reinstall OS X.
The disk drive is physically non-functional - Replace the hard drive.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD:
Boot From The Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

My MacBook Pro won't start up. What do I do?

My MacBook Pro won't start up. What do I do?

Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
    b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
     Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
     COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the
     computer and after the chime press and hold down the OPTION key until the boot manager
     screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
     Reinstall the 10.9.3 update: OS X Mavericks 10.9.3 Update (Combo).
4. Reinstall Lion/Mountain Lion, Mavericks: Reboot from the Recovery HD. Select Reinstall Lion/Mountain Lion, Mavericks from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Reinstall the 10.9.3 update: OS X Mavericks 10.9.3 Update (Combo).

MacBook pro freezes at start up

My MacBook pro freezes at start up at the gray screen w/ spinning gear.
I did a firmware update yesterday and this happened upon restart.
MacBook pro purchased new early 2011 lion

You need to back up your data before you do anything else, if it's still possible.
There are several ways to back up a Mac that is unable to fully boot. You need an external hard drive to hold the backup data.
1. Boot from your recovery partition (10.7 or later), a local Time Machine backup volume (10.7.2 or later), or your installation disc (10.6.8 or earlier.) Launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
2. If you have a working Mac, and both it and the non-working Mac have FireWire ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive.
How to use and troubleshoot FireWire target disk mode
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.

MacBook Pro does t start I turned it off during start up I've tried a lot of stuff. When I hold startup my hard disk says efi boot instead of Macintosh hd

MacBook Pro does t start I turned it off during start up I've tried a lot of stuff. When I hold startup my hard disk says efi boot instead of Macintosh hd

Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
If this does not work, then you will have to erase and reinstall Mountain Lion:
Install or Reinstall Lion/Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
      left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
        the Security button and set the Zero Data option to one-pass. Click on
      the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion/Mountain Lion and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.

I was messing around with .kext files in the MacintoshHD and now my MacBook Pro won't start up.

I was messing around with .kext files in the MacintoshHD and moved the system.kext and two others to my desktop and deleted the originals and now the MacBook Pro won't start up. All I get at start up is the apple icon then a bunch of text shows up part of which says Mac OS version: not yet set. then the apple icon turns into the power icon and tells me to turn off the computer. I've tried reinstalling from the install DVD by holding down option when powering on and selecting the install DVD and it just goes to a white screen with the apple icon and stays like that. I didn't have the disk utility on my Mac before this happened because I deleted it to make room on my computer a while ago so I'm not sure if that's why it won't load the install DVD but anyone who knows the solution to this with out going to get it repaired would be greatly appreciated. Thank you!

Never mind my dad just found the original install DVD and that worked. Before I was using an install disc that Apple sent me for another issue I was having, but thanks for replying so quickly and trying to help on this Thanksgiving day!!!

Hi! My MacBook Pro won't start! HELP !!!

Hi! My MacBook Pro won't start! I have tried everything I can think of like Safe Mode (doesn't work), Recovery (does not find Recovery Drive), Booting with OS Snow Leopard Cd (doesn't work)...
I have really no clue about what to do now... I paid quite a lot of money for this computer and am pretty short of money nowadays! Would like to repair with help rather than having to take it to Apple Store.
Has anyone had this same problem?
All I get is white screen + grey Apple and spinning grey disk... it's 100% frustrating! Any help would be more than welcome since I think i've tried EVERY SUGGESTION on this Support Center and Youtube videos...
This MBP is from 2011, runs on OS X 10.6.8
I tried booting with OS X Snow Leopard CD, it didn't work! (my cd player works! recognizes the Snow Leopard CD, but then never opens it... goes back forever to the with screen + apple and spinning disk)
I don't care about the content, it's OK if i lose all DATA... I just want to bring this Mac BACK TO LIFE!
When i run coomand on root# fsck -fy --> RESULT = my HD was checked and seems to be FINE!
Thanks

Please make a Genius Appointment and take it in for service.

My MacBook Pro doesn't start; in safe mode shift CMD V the message "disk0s2: media is not present" is written on the screen repeatedly but the MacBook doesn't start. Do you have any ideas of why this should be or what I should do to resolve this?

My MacBook Pro doesn't start; in safe mode <shift CMD V> the message "disk0s2: media is not present" is written on the screen repeatedly but the MacBook doesn't start. Do you have any ideas of why this should be or what I should do to resolve this? Thanks Eamonn

Thanks for these suggestions: I have tried safe mode re-starts (both "verbose" and simple "shift" + power) to no avail. I get the error message "disk0s2: media is not present". Following this I inserted the installation disc and from there ran disc utility. The "Verify Disk" indicated an error " invalid sibling link" which it could not repair.
I also tried to completely re-format/erase the disk, but again got an error message "disk object invalid or unable to serialize".
Any ideas of what could be causing this or the best solution? I fear I am fast running out of options.

When trying to install os x mavericks to my macbook pro as it started to install the computer now is stuck with the OS X Mavericks intall showing and I can't get out of it or force quit?

When trying to upgrade and install OS X Mmavericks to my Macbook Pro as it started to install the computer stopped the install and now is stuck with the OS X Mavericks intall window showing and I can't get out of it or force quit? I can not do anything else because this is stuck with this window/install screen showing. I have tried everything to get back to my regular desktop. I do not want to wipe the drive because I have photos on it that I want to save. So if there is any way to bypass this installer and get back to my regular desktop I would greatly appreciate the help.

UPDATE* Macbook7,1
Mavericks 10.9.4
8GB ram

MacBook Pro won't start up, can I transfer photos to iMac any way

My MacBook Pro will not start up after latest update, I contacted Apple Support who said I needed a thunderbolt cable, I purchased this and tried to put my photos onto someone else's IMac, iit won't work any suggestions please.

You may take out the HDD and install it into an enclosure. Then connect it to a Mac via USB and If the HDD is functional, you should be able to take the data off of it.
Ciao.

Spilled liquid on MacBook Pro - won't start - any suggestions?

spilled liquid on MacBook Pro - won't start - any suggestions?

Thank you both for your responses! I watched a video on how to remove the hard drive - special tork(?) screwdriver and too many steps for me to feel confident about doing it myself, so I took the computer to an Apple Store - and thank God, the hard drive appeared undamaged - they are transferring the data to a new Macbook Pro. The loss of data was the scariest part, so I am breathing again!
The laptop was three years old, I was hoping for another year or so before upgrading, but such is life. I appreciate your upfront advice.

HT204347 what to do if my macbook pro is not starting and I do not have warranty?

I need help...my macbook pro is not starting. I tried everything..Can I send it to the Apple store for an estimate and how much would that be?
Thanks

emdonahue wrote:
I need help...my macbook pro is not starting. I tried everything..Can I send it to the Apple store for an estimate and how much would that be?
Thanks
Yes and ask the repair tech.

Macbook pro isn't starting

my macbook pro isn't starting. it gets as far as the apple logo and loading wheel but does go any further, please help!!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. The easiest way to deal with the problem is to boot from an external drive, or else to use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 9
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Repeat Step 9, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Macbook Pro Frozen upon start up

Similar Messages

Maybe you are looking for