Operation split in setup time formula

Hi, while creation of Work centers, i have seen the formula for setup as setup * operation splits. what is meant by operation split? pls explain?

Hi,
Operation split means no. of workcenters.
It is used in workcenter scheduling tab processing formula. For example operation split is 2. Say a process required processing time 1hr in one machine scheduled from 9.00am to 10.00am . If operation split is 2, system scheduled from 9.00am to 9.30am due to 2 machines.
And it is used in capacity tab setup formula. For example operation split is 2. Say a process required setup time 10mins in one machine. If operation split is 2, system will calculate setup time is 20mints because 10mints x no.of workcenters (split).
Regards,
Dharma

Similar Messages

Setup time

Hi, During confirmation with co11n, if the yield qty is more than 1, observed that the setup time is proposed as the setup time req for 1 qty only. it is not multiplied by operation qty. please advise what need to be done to get the total set time required for total yield qty. please advise.

Dear ,
What is the Setup Formula are u assining to your work centre -CR02-Capacity Tab /Scheduling -Execution Tab .
I hope the standard one is Set up Formula : SAP001 =SAP_01 , Here SAP_01 is a Time dimenstion with Min as Unit .There is no multiplication of Qty .You can chek the same in OP55 and then OP52
Now , if you want to consider the operation qty which will be multiplied , then you should go ahead with (OP55/OP52)
SAP003 = SAP_03 * SAP_09 / SAP_08 / SAP_11 where SAP_03 --Lbr Hrs
SAP_09 -Operation Qty
SAP_08 -Base Qty , SAP_11-Operation Split timin
Hope this is clear to u
Regards
JH

Routing setup Time based on material length

Hi All,
I have a situation where i have to write an Object Dependency to change the setup time of an operation based on the length of the material selected by the customer.
For the first 5 inches, the Setup time should be 4Hrs, for each additional 5 inches the Setup time should be increased by 1Hr. there is no limit on the length they can select.
I have created a Reference Characteristics SETUP_TIME, and have a Characteristic called LENGTH. I could use some help with writing the dependency.
Thanks for the help.
Raj

Hello Raj,
Please review the link . You can create a procedure as defined in this link.
http://help.sap.com/saphelp_47x200/helpdata/EN/92/58c3a1417011d189ec0000e81ddfac/frameset.htm
Eg ,
$SELF.SETUP_TIME = MDATA $SELF.SETUP_TIME + 30 IF COLOR = 'FL'
OR $SELF.SETUP_TIME = $SELF.SETUP_TIME + 30 IF METALLICEFFECT = u2018Yesu2019
You should only usee MDATA if you reading the value from master data ,for a changed value you do not need to use MDATA.
You can also achieve this by usingVariant functions in a procedure. You can write a code to do a calculation based on the values you are sending. Assign this FM (OD) to the reference characteristic. You can find more information on this on the following link.
http://help.sap.com/saphelp_47x200/helpdata/EN/92/58c6eb417011d189ec0000e81ddfac/frameset.htm
Hope this helps
Thanks Amber

VC - Dependency for routing setup time

Hi all,
During dependency editor programming, I had this difficulty with creating a procedure for summing up the setup time in the routing.
We have 3 components A,B,C as multiple selection in a characteristic with variable BOM quantities.
Based on the selection of these components, we have characteristics called QA,QB and QC to obtain the quantity of the respective components and pass it on to STPO-MENGE of the specific components.
We have another procedure which sums up the total of QA, QB and QC and multiplies this to the setup time in the routing for a particular operation.
The code for this dependency is:
$SELF.SETUP_TIME = MDATA $SELF.SETUP_TIME * (QA + QB + QC).
The issue we have here is the code calculates the setup time only if all the 3 characteristics QA,QB and QC is filled.
We want the QA,QB and QC characteristics to be displayed only if that particular component is selected. Can anybody suggest how to code the procedure to output a sum even if one of the characteristics is not SPECIFIED.

$SELF.SETUP_TIME = 0,
$SELF.SETUP_TIME = $SELF.SETUP_TIME + QA
   IF QA SPECIFIED,
$SELF.SETUP_TIME = $SELF.SETUP_TIME + QB
   IF QB SPECIFIED,
$SELF.SETUP_TIME = $SELF.SETUP_TIME + QC
   IF QC SPECIFIED.

Routing operation split

hi all,
I have defined 2 splits in the work center. Operation split is ticked in routing.
When I create an order for 10 units , it is getting split as 7.5 and 2.5. i would like to know where this proportion is defined if it can be ?
Regards,
Yogesh

Yogesh,
In the operation details you need to activate the Required Splitting indicator and maintain the minimum time for splitting, based on this system calculates the number of splits by dividing the processing time for the operation by the minimum processing time.
Regards,
Prasobh

View Setup time in the DS planning board

Hello Everyone. I maintained setup time for a resource but it is not displaying in DS planning board. What could have I missed? Thanks.
Michelle

hello,
first check the operations of the order.
right click on the produce operation and navigate to Order Processing.
In the order tree open all nodes for operations.
Is the set up activity visible there?
If yes doble click on the activity.
does the set up activity have a duration?
If yes check the status of the set up activity.
go back to the planning board.
in the menue select extras-> Legend
a pop-up with the graphical objects is displayed.
Check the graphic objects for the activity status you read before.
did you change the customizing settings for the graphic object?
If yes check them again or reset them to the default SAP settings.
I had a similar problem with a set up activity when I wanted to change the color of the activity according to the set up group. I changed the settings in the customizing Maintain Planning Board Profiles.
It is very difficult to maintain the decision table for graphical objects.
If you did this recheck the decision table.
Go back to the SAP default settings and check the planning board again.
Are the set up acitvities displayed now?
Then the porblem is with the decision table.
rethink every step again.

Displaying all Operation Splits for an Order in WorkOrderList MAM3.0

Hello Experts,
I have the following requirement in MAM3.0.
Mobile Infrastructure 7.0
1. All the Operation Split details from operation list needs to be added in orderlist based on the check for userid from MAM30_090.
2. Order List to be sorted, arranged in a particular manner and hiding certain fields in the jsp.
Please provide the solutions ASAP.
Thanks and Regards,
Mani

Hi,
As far as I know thats how standard MAM works. For any gloabl order, if you create notifications on the client, they fall under order objects list.
The only way from the client you can achieve your requirement is, when you create both order and notifications on the client locally. That means, first create the order locally, and before sync, rom the order header details click on notification create button and then create a notification. This way both order header will have notificaiton number and viceversa. And later, all the notifications created for that order falls under order objects list and the first created notification in the order header.
For your second question of status change of order, from the error it looks like you are changing the status on the client and the middleware detects a conflict when you do a sync(but i think you are not modifying on the backend at the same time). Kindly check on the backend if you have missed to apply any related notes.
Regards,
Siva.

Operation splitting

Hi,
I have created individual capacities say for example w1 and w2 in work centre wrc1.in routing I have mentioned required splitting and given 2 as splits.in routing work centre wrc1 is assigned to operation.
I want to dispatch operation quantity 10 into these two work centres w1 and w2 , 5 quantites each so that both the operations can start at thje same time and finish quickly.
how to do this capacity levelling?In CM25 i can see work centre wrc1 but not its individual capacities i.e w1 and w2?
please reply.
Regards.

Dear,
Capacity leveling transaction "CM21" you would be able to dispatch individual operation quantities to the individual machines.
For operation split you have to createM/c with 2 Indiviudal capacities and have also defined the Individual Capacities by name in the Capacity header CR02. Also in the capacity header you should have activated "Relevant for Finite scheduling".
In the Scheduling parameters for the order type/Plant you should have activated check box for "Generate Capacity requirements" in transaction OPU3.
You can only "Dispatch" the same in CM27 by assigning in "Cap. reqmt assignment" in production order. The indicator "D" is set only after the split is dispatched.
Hope clear to you.
Regards,
R.Brahmankar

I am trying to setup time limits in airport 5.6

I am trying to setup time limits for internet usage in airport 5.6—
but i don't get a timed access control "option. Tried on both imac and macbook pro.

What are you setting it up as.. join wireless network .. the very worst setup, it will disappear.. reboot the whole network in order modem. router TC.. clients and it will likely reappear.
Tell us what network setup you are using..
If you setup with cable to a computer completely isolated from the network with TC also isolated.. finish the setup of everything you want. .before update.. then plug it into the network. .then restart everything in correct order.. it will work most of the time.

HT1926 My iTunes installer was interrupted & now it's telling me "Your system has not been modified. To complete these operations at a later time, please run the installer again". The only problem is, I've tried to run it about six or seven times. Can s

My iTunes installer was interrupted & now it's telling me "Your system has not been modified. To complete these operations at a later time, please run the installer again". The only problem is, I've tried to run it about six or seven times.

I'm not sure anyone here knows more about the Java plugin than you do...
Were you starting the control panel from disk as administrator because it didn't work starting it through the Start menu (if you have Control Panel set to View by Category, the Java control panel is under "Programs").

Document Splitting at the time of Bill of exchange

Dear All,
issue is related to Document Splitting at the time of Bill of exchange
I booked 2 different Customer Sales through FI, but both invoice have different Profit centre.
Entry is like
Customer A/C Dr 1000   Pc 1100
To Sales A/C     1000     PC 1100
Customer A/C Dr 2000   Pc 1200
To Sales A/C     2000     PC 1200
Now from customer we received a single bill of exchange, so that we booked from it from f-36
Now at the time of Discounting through T-code F-33 when we mentioned both the bill with system not able to split the document.
And showing the error Balancing field "Profit Center" in line item 001 not filled.
Regards,
Shyam

Hi,
   Document splitting there in item category 001 check and put profit center is optional.
Regards,
Srikanth.Madani

When I create a Planned order using PDS, the Setup time is coming as 0.

We have been using PPMs for a long time, and now we are trying to migrate to PDS.
We are currently in SCM 7.0.
I successfully created the PDS in APO (using CIF from R/3). In the PDS (in APO), for a particular activity, I see the activity type is "S", and the Activity Duratiion (Fixed) is 43,200 Seconds.
However, when I create a planned order using this PDS, the activity time is zero (End time = Start Time).
When we use the PPM the setup time comes correctly.
Any help will be appreciated..

Senthil,
Thanks for your views.
I have checked all that you have suggested, and it is okay. The issue still persists.
One thing that I noticed was that it is working fine in the old SCM 5.0 environment - the setup time is coming correctly in the planned order.
However, we have this issue in the new SCM 7.0 environment. Is there something that is different in SCM 7.0 in terms order explosion ?
Reagrds,
Sastry

How is easy is to setup Time Capsule as a wifi router

How easy is it to setup Time Capsule as a wifi router?

The following would be the basic setup steps for the Time Capsule (TC):
Modem/Router Power ReCycling
o Power-off the Cable modem, TC, & computer(s); Wait at least 30 minutes.
o Power-on the Cable modem; Wait at least 15 minutes.
o Power-on the TC; Wait at least 5 minutes.
o Power-on the computer(s)
Either connect to the TC's wireless network or, temporarily, connect your computer directly (using an Ethernet cable) to one of the LAN ports of the TC, and then, using the AirPort Utility in Manual Mode, check these settings:
AirPort - Base Station
o Base Station Name: <whatever you wish or use the default>
o Base Station Password: (optional)
o Contact: (optional)
o Location: (optional)
o Set time automatically (optional)
o Time Zone: <select your time zone>
o Status Light: Always On (Default)
o Allow configuration over Ethernet WAN port (unchecked)
o Advertise configuration globally using Bonjour (unchecked)
AirPort - Wireless
o Wireless Mode: Create a wireless network
o Network Name: <whatever you wish or use the default>
o Allow this network to be extended (unchecked)
o Radio Mode: 802.11n (802.11b/g compatible)
o Channel: Automatic
o Wireless Security: None
AirPort - Wireless - Wireless Options
o Region: <select your region>
o Multicast Rate: 2 Mbps
o Transmit Power: 100%
o Create a closed network (unchecked)
o Use interference robustness (unchecked)
Internet - Internet Connection
o Connect Using: Ethernet
o Configure IPv4: Using DHCP
o IP Address: <provided by your ISP>
o Subnet Mask: <provided by your ISP>
o Router Address: <provided by your ISP>
o DNS Server(s): <provided by your ISP>
o Domain Name: <provided by your ISP>
o DHCP Client ID: (optional)
o Ethernet WAN Port: Automatic (Default)
o Connection Sharing: Share a public IP address
Internet - DHCP
o DHCP Range: 10.0 1.x
o DHCP Beginning Address: 10.0.1.2
o DHCP Ending Address: 10.0.1.200
o DHCP Lease: 4 hours
o DHCP Message: (optional)
o LDAP Server: (optional)
o DHCP Reservations: (optional)
Internet - NAT
o Enable default host at: (leave blank)
o Enable NAT Port Mapping Protocol (checked)
Once you have verified Internet access, I strongly suggest that you use wireless encryption (WPA or WPA2) to secure your network.

How to measure the Data setup time

I want to do a SPI timing AC characteristics.
I use labview capture a frame of SPI data package from a oscilloscope and display in a waveform Graph.
Lead time, Data setup time, data hold time... should be measured.
So, what is the next step should i do?
Thanks

Thank you, asastet.
I test the SPI module of a MCU. I have download a code to init the SPI and transfer a data package continuously.
The 4 channels of oscilloscope connected with SS, CLK, MOSI, MISO.
In labview, I capture a frame of SPI data package from oscilloscope and display in waveform graph control.
My project will automatically measure the data setup time and data hold time according CLK vs. MOSI.
Thanks.

Print time formula error when used in cross-tab

I have a cross-table that I'm using to calculate revenue, which is based on a conditional formula. Within that formula is a Running Total field. When I use this field I get the following error message: "A PRINT TIME FORMULA THAT MODIFIES VARIABLES IS USED IN A CHART OR MAP".
My problem is that I am using the Running Total because the values are duplicated by the number of detail lines. I think this should be a relatively easy fix, but I am stumped.
Thank you,
Any help you can provide is greatly appreciated!!!
Marlene
Crystal Reports Professional, 11.5.8.826 (on Progress Server)

Please re-post if this is still an issue or purchase a case and have a dedicated support
engineer work with your directly

Operation split in setup time formula

Similar Messages

Maybe you are looking for