PM/QM Integration for Calibration of Equipment /Measurement Instrument QC

Dear Friends,
I want to have inspection lot for calibration of Lab equipment
what i understand is
Creating the Maintenance Plan
Assigning and Displaying the Task List 
Scheduling the Maintenance Plan  
Displaying the Calibration Order and Inspection Lot
Entering Characteristic Values 
Entering the Usage Decision 
but just want to know what are the basic setting to activate inspection type 14 , do i need to treat Equipment as material master or is there any place to activate inspection type 14 in   Equipment
Thanks & Regards
Raj

Dear Ram
The 14 inspection type is to be activated in the config
1) SPRO>QM>Quality inspection> inspection lot creation> inspection in plant maintenace> maintain 14 against the order type you are going to use. Normaly PM05 is used.
Things to be noted
1) Inspection lot is created when order is released and saved
2) in task list you have to have a sampling procedure which has a tick in plant maintenance ( QDV1)
Check and revert back
Regards
gajesh

Similar Messages

  • PP and PM integration for PRT equipment

    Hi,
    i got integration issue when implementing PP and PM.
    i used PRT equipment with counter, PP confimation will update the counter.
    If it reach some value it is overhaul and maintenance order created.
    1, if it is overhaul, can i automatically set the PRT so it is not available (status)
    2. can PP people know this and the they reschedule the PP order and it schedule automatically considering the maintenance order for the PRT equipment they use.
    after PRT equipment i will user work center as equipment too and then we will have botj issue as above
    is it really possible for pp and pm integration like this.
    please kindly help.
    best regards,
    Freddy Ha

    hi
    In the normal process once your production order is confirmed ,your maintenance order from plan will be triggered ,but your PRT status is in release only which will not be updated as LOCK automatically .it can be locked manually in the Master data.
    check with abaper whether it is possible to update the status using measurement document ,for say once it reaches 2000 pc
    Once the status is locked it cannot be used for maintenance or production order
    for Workcenter as equipment then you can process with System condition as Not in operation which will show the maintenance order while checking the production order planning table
    regards
    thyagarajan

  • Measuring point in equi[ment for calibration cycle.

    Hi All,
    Can any body tell me how to use Measuring point and measuring document in calibration - in Equipment.
    Its urgent for me
    Thanks
    Siddhesh

    hi siddesh
    iam not having any doc. please follow the link in that a model company has performed all the operation in PM
    <b>http://help.sap.com/saphelp_46c/helpdata/en/fe/67f9609d6f11d189b60000e829fbbd/frameset.htm</b>
    regards
    thyagarajan

  • Sending Gauges / Equipment for Calibration

    I want to send the Gauges / Equipment for Calibration to Outside party (Vendor). Would you please tell me how to map this process in SAP.
    The process is:
    1. Gauges / Equipments are sent for Calibration to vendor.
    2. Vendor Calibrates and those are verified for the usage.
    Your valuable inputs will be helpful, points will be awarded accordingly.
    Thnkx and Regards,
    Rashmi

    hi rashmi
    while planning the calibration order , create  a task list with a control key for external operation, and maintain the requiured outline agreement or services.while scheduling a PR will be generated then you can process further. you can also look in to the web site for better understanding "http://help.sap.com/saphelp_46c/helpdata/en/fe/67fbcc9d6f11d189b60000e829fbbd/frameset.htm"
    regards
    thyagarajan

  • Test Equipment for calibration

    Dear Experts,
    Is it necessary to create Calibration Orders against Test Equipments only ?? or we can do the same against Machines also??
    As in some cases there is preventive & calibration plan against same equipment then if we create Test equipment,, there is going to be doubling of equipment??
    Plz guide
    rgrds
    DM

    Dear DM,
               For the same Equipment U can distinguish one is M - Machine     , and Q- Test Equipment  categories.
    So u can do  preventive maintenance and caliberations plan also
    If u not clear pls come back
    Regards
    SMC

  • Sending equipment for calibration

    Dear all,
    what is the process to send test equipment for calibration.
    ours is external calibration:
    as per QM they are running the scheduling for calibration so system automatically creating one purchase requisition .
    so then how to send that equipment through MM .
    please give step by step
    regards,
    prasad

    Hi,
    Generally, Repair of Materials are handled via concept of Gate Pass (Returnable & Non-Returnable). But, SAP doesn't provide any option for creating Gate Pass (Returnable & Non-Returnable) in standard.
    Try the below suggested procedure as a work around process;
    Repair Process via Returnable Gate Pass: -
    1. MM01 - Create Material Master for every Spare Part / Machinery to be sent to Vendor for Repair as Non-Valuated (Material Type "UNBW") (Do not extend Accounting and Costing views since you don't require postings of Stock value and consumption values, you only want to track the Service/Repair Charges)
    It's not necessary to have materials as Non-Valuated always, it depends on your requirement.
    2. MIGO - Goods Receipt > Others (Receive the quantities of these materials using Movement Type 501 / 511) - Only if Stock of Material is not available.
    3. ME21N - Create Subcontracting PO (Here Main Material and Component will be same material)
    4. MB1B - Transfer Posting w.r.t. Subcon PO (Mvmt Type - 541, Spare Part stock will get posted to Vendor Stock)
    5. MB90 - Take Print out of this Material Doc as Returnable Gate Pass (U need to configure Message Determination of Inventory Mgmt)
    6. MIGO - GR against Subcon PO (101 - Receive Spare Part, 543 O - Consumption of Spare Part form Vendor Stock)
    7. MIRO - LIV for Service Charges w.r.t. Subcon PO
    Note: - If PM Module is implemented then use PM Order as origin of the Repair Process. If it is not then follow the above process.
    Else if you don't want to track the material stock then follow the Service Process Cycle
    1. ME21N - Create Service PO (With Item Category D and Account Assignment Category K )
    2. ML81N - Create Service Entry Sheet w.r.t. Service PO
    3. MIRO - LIV for Service Charges w.r.t. Service PO or Service Entry Sheet
    For Service Process, refer following link;
    [SAP External Service Management|http://www.sap123.com/showthread.php?t=52]

  • Equipment sent out for calibration

    I have a scenario where for calibration i am sending the equipment to vendor for calibration.
    i am creating equipment as material and sending it out with help of sub contracting P.O -so that returnable gate pass can be created .
    Now my quetion is how can i track this cost in my order for sub contracting P.O.

    hi
    please try this below, you can get the actual costs in the order upon service entry sheet confirmation.
    >Create calibration order
    >Create P.O with account assignment category F.
    >Enter the calibration order number in the account assignment field
    >Create entry sheet and confirm
    >actual costs can be captured in the calibration order.
    Regards
    Seenu

  • What is the proces flow for calibration equipement management

    Hello,
    Please can some explain the Process flow for the equipment management?
    We want to schdule the order for the calibration equipement.
    Gaurav

    Please follow the following prcoess flow
    IA05- Create General Task list(Enter inspection point :300,operation,inspection charactertics to the operation,usage)
    IP01-Create plan( Use maintenace startegy of plant,enter equipment, select general task list for plan the equipment,enter call horizon,planning cycle schduling period)
    IP42-Schedule the plan Schedule the plan for the quantity with frequency defined in the plan.Which schdule the according to the schdule date.Schedule date generates pm order for the plan on due date.
    IW33-Display order.
    QE51-Calibration result recording for equipment- Gives status for result i.e ok or not ok.
    QA11-Lot usage decision
    IW41-Confirmation for the order.
    You can refer the sap librabary for detailed process.
    Regards,
    Sunil Patil

  • Background Scheduling of Maintenance order for Calibration.

    Dear Experts,
    I want to scheule my calibration order in QM for calibration of Test Equipment in background.
    I have created my maintenance order for calibration of Gauges / Instruments (which are defined as Equipments). The dates for the calibration have been calculated based on time. When I go to the transaction of scheduling the order & save, the inspection lot for calibration is generated & the equipment task list is assigned to the lot.
    I want this to automatically happen in background. This is because I have thousands of equipments, for which I can not schedule the calibration manually.
    Regards,
    Prashant

    Hi,
    Please check below link if this can help it.
    http://help.sap.com/saphelp_scm2007/helpdata/en/c3/9e443cfb06e532e10000000a114084/content.htm
    Regards,
    Anil

  • Digital signatures for calibration inspection (inspection type 14)

    Hi,
    I want to use digital signatures for results recording and usage decision (ud) when performing a calibration (inspection type 14). Normally you'd set-up the material authorization for digital signatures. But this can't be added to maintenance plans or equipment. Is there any way to set-up digital signatures for calibrations?
    Regards,
    Maarten

    Explore SAP Note 576307
    It may help u.

  • Measuring Instrument Needs to be added in inspection plan for each part

    Hi
    How to assign the Measuring Instrument in the quality inspection plan for all the materials.
    Whether i need to assign as material assignment or as PRT.
    how to use prt to assign to the operation in the quality plan (task list)
    Thanks
    VRAJ

    Hi,
    when i try to assign the Equipment for first Inspection Characteristics.
    the system thru the ERROR as,
    Production resource/tool is not intended for this type of task list
    Message no. CF230
    Diagnosis
    You want to use the production resource/tool in a task list or work order with task list type Q. However, according to usage 004 of the PRT, this task list type does not exist.
    Procedure
    Change the usage of the PRT in the master record or select a PRT which can be used in this task list type.
    How to resolve this issue.

  • Order processing for defective measuring instrument

    HI experts,
    i want to know how to handle order processing for a defective measuring instrument.

    Hi Nandi,
                  In addition to what Mr Maheshwaran has said, you can maintain the PRT's also.
    as the PRT Equipment will allow you to do the Maintenance activities on them.
    Hope it helps you Further.
    Regards,
    Yawar Khan

  • No inspection lot for calibration

    Hi all,
      I am facing one problem in equipment calibration.The problem is that no inspection lot is generated for calibration
    I have maintaimed following seeting
    1)Equipment cration(IE01)
    2)Created eqipment task list ( IA01)
    3)Created maintenance plan (IP41) wherein order category is maintenance order and order type as  calibration order.
    4) And sheduled the plan ( IP10)
                Inspection type is already active against the order type
    Please guide what i am missing is the orde category correct?
    thanks
    ASD

    Hi,
    Also please check the following settings in SPRO
    SPRO  --> plant maintenance -->  maintenance and service processing --> maintenance and service order --> assign inspection type to maintenance/service order type
    here u have to assign inspection type 14 to your respective order type for calibration secenario
    please check and revert back.
    Regards,
    Vinay

  • AS03 : How to hide 'Integration of assets and equipement' from Allocations

    Hi,
    In Allocations' table (Asset master data AS03) I want to hide fields relating to 'Integration of assets and equipement'
    Please advise
    Regards.

    Hi,
    First identify the screen layout assigned to the Asset Class under which Asset has been created and you want to change the status of the field for....then use below path to get that done...
    Financial Accounting ® Asset Accounting ® Master Data ®Screen Layout ® Define Screen Layout for Asset Master Data
    Select Define Screen Layout for Asset Master Data
    Regards,
    Chintan Joshi

  • SAP Business one 8.8 Integration for SAP Netweaver

    hi all,
    Where to download SAP Business one 8.8 Integration for SAP Net weaver Components(Installation Packages for 32 bit). I installed one B1iSN but its only Integration for SAP Business One Not for SAP Business one 8.8 Integration for SAP Net weaver.
    Please send me the link. Its urgent
    Thanks & Regards
    B.Lakshmi Narayanan

    Hi
    [https://websmp104.sap-ag.de/sbo-swcenter]
    Software Distribution Center >SAP Business One Products > Updates
    SAP Business One 8.8 >>>  SAP B1 8.8 INTEGRATION FOR NW >>>Comprised Software Component Versions
    B1 8.8 INTEGRATION CONTENT
    B1 8.8 INTEGRATION SIM
    B1 8.8 INTEGRATION TECHNOLOGY
    Hope you find.
    Thanks
    Kevin

Maybe you are looking for