Post Invoice aganist Contract

Hi,
I have a scenario where i have to post invoice again Contract, I am not able to post using MIRO and FB60 or i may be approaching wrong.
Could somebody please tell me how to approach to this problem? should i use any BADI? if yes could you please tell me what is the BADI name?
Thanks for your help
Sarath

Hi,
You have to create Service Master and Service Entry Sheet for creating PO for Contract. The Check Vendor created in a seperate group. Please take the help of MM Consultant to proceed.
Sadashivan

Similar Messages

Security Dept Statistical posting from SD invoice to Contract accout

Dear Friends,
Could some one help me, How the Security Dept Statistically posted from SD invoice to Contract accout level.
Because, the Security Dept amount should not directly post into any G/L account while creation of SD invoice.
Thanks in advance.

IF a payment has been made to the security deposit, that entry will be reflected at the time of invoicing. That is a standard process.

Getting error while posting invoice in T-code F-02

Hello,
When i try to post invoice in T-code F-02 gives me the error message"There is no item category assigned to account bank a/c/company"
Can any one suggest me why this is error came up and how to resolve this.
Thanks,
Lavi

Hi,
I think u have activated doc splitting i.e. new gl acconting. Go to
Financial Accounting (New) > General Ledger Accounting (New) > Business Transactions > Document Splitting > Classify G/L Accounts for Document Splitting
And make setting for u r account. Also see all the nodes there are configured, to avoid any other error.
Regards

Error while posting Invoice verifycation

Dear All..
At the time of posting invoice verifycation in miro for service order .The error is coming "No business area in the line item please check" But in that line item business area already mentioned.
Please resolve this problem.
Usefull answers will be rewarded.
REgards
Kumar

hi,
T.code:OMJ7, link plant and division to your business area...
In Service Master enter division while creating with AC03 t.code.
Note:In T.code OX03 - Create the new Business Area
hope it helps..
Regards
Priyanka.P

Error while posting Invoice IDOC (The difference is too large for clearing)

Hi All,
While posting Invoice IDOC to Remittance Advice IDOC get fails with status 51 & message ' The difference is too large for clearing'.
Please suggest any solution or reason to fail IDOC.
Thanks & Regards,
Ajay
Moderator message: please search for information and try to find out yourself before asking, this will be a functional problem anyway that should be asked in the appropriate forum, e.g. ERP Financials.
locked by: Thomas Zloch on Aug 20, 2010 1:59 PM

Pls check the tolerance amounts limits:
SPRO--- F/A --AR/AP -
Business transactions -Open item clearing--- Clearing differance---- Define / Assign tolerance groups for emp -
Where you need to change the limits of max amounts with the %
Let me know for any info.
Regards
Suresh

Disable 'Delete' button for posted invoices in GOS Attachment List

Hi,
when i open the attachement list of a generic object i see the attached files. In this dialog i want to disable the "Delete" ( attachment) button for Posted invoices ( In MIR4 tcode -> If the invoice is already posted it should not allow to delete the attachment )
I read oss notes and some ides of copying diverse classes but nothing really helps.
I found two badis
GOS_SRV_REQUEST
GOS_SRV_SELECT
but i dont know where we have to write our code .
I read so many posts related to attachments but all the places described about authoriztion object .
Can you please give some ideas to disable the delete button for posted invoices.

Hello,
For GOS there is no SAP Standard authorization concept. The only way to
manage GOS authorizations is implementing it via custom code as
described in SAP Note: 491271.
Please have a look at the SAP notes:
491271 Authorizations for generic object services
701609 Authorizations for services: Final classes
For the use of S_OC_ROLE: this object states if a user is an office
administrator he can create, modify or delete every document, even
those created by other users. If the user is not an office admin, the
user is still able to create his own attachments.
Regarding to the issue, there is an role object S_GUI for upload.
To match your inquiry, pleaes find the user's role and active the
object S_GUI.
Regards,
David

Getting problem while posting Invoice

Hi all,
Ofcourse this problem is related functional thing, i am posting in ABAP group. we are getting problem while posting invoice through f-43 transaction. The error is "Fiscal year 0000 not allowed for year-dependent commitment items". Please let me know if u have any solution.
Thanks in advance.
chandrasekhar.

Hi chandrasekhar,
pls post some infos:
1) application aerea of the message and message no.
2) document date / posting date
and ohter date-fileds of the document
3) SAP-Release
Have you search in SAP-OSS with the message no. or
message text ?
regards Andreas

Asset in incomplete while posting invoice MIRO

Hi All,
I have raised an P.O with account assignment 'A' P.O has created but while posting invoice through t.code Miro i am getting the error 'asset co.code xxxx asset no.xxxxxx is incomplete.
let me know were i need to check.

Hi Ganee,
The asset for which you are doing MIRO, the error might be due to the following reasons:
1. Check the depreciation Key.
2. Check the Account Determinations (Ao90)
You can do resolve your error.
Regards
VG

Capture & Post Invoice at the time of Goods Receipt in one Step

Hi,
We are doing the following for Goods Receipt (as decided by other consultant)
1. Goods Receipt (Only Part I) - currently being done by Stores
2. Capture Invoice (J1IEX) - currently being done by Purchase
3. Post Invoice (J1IEX) - currently being done by Finance
We tried to capture & Post Invoice in single step at the time of Goods Receipt. The system is allowing us to do so. Can we do the goods receipt & capture & post invoice at the time of GR only.
What is the difference or benefit in doing GR & capturing invoice separately?
Regards,

>
PK wrote:
> Hi,
>
> We are doing the following for Goods Receipt (as decided by other consultant)
> 1. Goods Receipt (Only Part I) - currently being done by Stores
> 2. Capture Invoice (J1IEX) - currently being done by Purchase
> 3. Post Invoice (J1IEX) - currently being done by Finance
>
> We tried to capture & Post Invoice in single step at the time of Goods Receipt. The system is allowing us to do so. Can we do the goods receipt & capture & post invoice at the time of GR only.
>
> What is the difference or benefit in doing GR & capturing invoice separately?
>
> Regards,
Hi PK,
Standard SAP provides different stages based on business criticality.
Since a warehouse person may not be aware of Excise functionalities he should only be allowed to capture the invoice, however Posting excise credit is a critical business function hence site Excise clerks should be allowed for these rights.
However based on business scenario or size of business the same can be done at one place.
So as your business demands the process can be changed with that. However criticality of the matter & process lies with the business finally.
There are scenarios where actual material reciept is short at times hence credit allowed has to be reduced than original, there may be scenarios where a critical excisable product may have wrong chapter heading maintained at PO level which needs to be changed at credit availment/capture stages to show correct chapter in excise registers...
these all cases support the process to be splitted & responsibilities segrigated....
Hope it assits....
regards
ak

Exchange rate gain /loss is not posted in the contract

Hi Sap People,
Exchange rate gain /loss is not posted in the contract(cashflows). This is w.r.t SAP Banking Module.
The open items are posted with a certain exchange rate in the contract at the time of disburesment,while clearing thru FF68(incoming payment) with a new exchange rate the items
are cleared with the same exchange rate and the Exchange gain/loss is posted as zero.
Regards
Ravi

Hi,
Check the exchange rate type for the disbursement. It is M for FF68. Check in configuration the exchange rate type. Also check the exchange rates maintained in OB08 for this exchange rate type and confirm if there is any difference.
Is it Loans module?
Regards,
Ravishankar

Runtime error in MIRO posting invoice for SES's created in CATS

Hi Gurus,
We are having an issue when posting invoices in MIRO referred to SES created in CATS.
It always took much longer the system to process those SES created via CATS than those from the standard MM (ML81...) but the situation today is so critical that we can not pay the vendors for which SES are created via CATS. Runtime error is obtained when trying to post a SES for 900$ value.
This problem does not happen in our integrating/testing system.
Do you have any idea why this is happening?
thanks to everyone in advance,
VL

Hi,
have you searched for notes with the runtime error details?
Has also a short dump occured (transaction ST22) ? Please give more detail information.
Regards,
Edit

How to post invoices in FI-CA related to outgoing payments

Hi
We need to make payments to vendors for our business. We are creating vendors as business partners in FICA and invoices have to be posted in FI-CA. Can someone tell me the configurations to be done for posting a invoice before making the payments. What would be the main and sub transaction for the invoice and outgoing payments?
Thanks
Santosh
Edited by: Santosh Kolleti on Nov 20, 2008 11:00 PM
Edited by: Santosh Kolleti on Nov 20, 2008 11:00 PM

Santhosh,
Are you trying to Post Invoices in FICA or just FICA document with Invoice Refer no?
If former, it is a very big config and you need to sit with Billing Consultant.
If latter, suggest you to populate value in Reference number.
You can use any MT/ST that are used to post Open items like 0010/0030 etc
Hope this helps
Rgds
Rajendra

"Post Invoice and Payment seperately"

Hi Guys,
I need help on resolving this issue.
We are posting a vendor downpayment using F-48.
We are then doing a vendor invoice and subsequently clearing the open items using F-58. But we are getting the following error while posting
"Deferred Tax : Post Invoice and Payment seperately $1"
Thanks,
Srikanth.

hi,
Do you have two tax codes setup up. One tax code to post with the invoice and another one which is used for transferring when the invoice payment is made. Please check that you are using the right tax code setup for the posting with the invoice.
Regards
Girish BP

'Deferred tax: Post invoice and payment separately $1

Hi
A customer invoice is posted with service tax.If we go to f-04 to make
an entry of payment received and Debit bank, debit TDS certificate
receivable for the TDS amount deducted and click on process open items
thereby selecting the customer and then the invoice the system throws
the error as 'Deferred tax: Post invoice and payment separately $1
Message no. DEFTAX020'
And if we try to post it by selecting posting key of credit customer
which will not do the clearing of invoice, the error does not come.
We are using deferred tax transfer New : RFUMSV25.All the other
processes relating to service tax are going fine.
Please suggest.

Hi
A customer invoice is posted with service tax.If we go to f-04 to make
an entry of payment received and Debit bank, debit TDS certificate
receivable for the TDS amount deducted and click on process open items
thereby selecting the customer and then the invoice the system throws
the error as 'Deferred tax: Post invoice and payment separately $1
Message no. DEFTAX020'
And if we try to post it by selecting posting key of credit customer
which will not do the clearing of invoice, the error does not come.
We are using deferred tax transfer New : RFUMSV25.All the other
processes relating to service tax are going fine.
Please suggest.

Filling alloction field for a subledger account by posting invoice by MIRO

Hi, at this moment I am struggling with a problem concerning filling the field Allocation at line item of an GL account. When I am posting invoice by MIRO, I want to see certain information on line item of an GL Account. When I am posting an invoice by MIRO, this field is for P&L accounts and balancesheet accounts filled with the value such a determined in FS00, tab Control data, field Sort Key. So therefore all my accounts has the sort key Purchase order. When posting invoices by MIRO, the posting in FI, is showing me on line item level the PO-number in the field Allocation.
However, when I am posting an invoce by MIRO on an reconcilliation account for asset, the allocation field is empty, MIRO is not filling this field automatically. Although the settings of the sort key is the same as for other balance or P&L accounts.
Has anybody an idea how the allocation field can be filled automatically for an reconcilliation account for assets

Hi
Run the program RM07CUFA
in SE38 Tcode and check the inconsistencies.
Also in FS00 go to details of the GL account and double click on field status group under create bank interest tab and then double click material management/additional assignments.
You can see the required or suppressed fields

Post Invoice aganist Contract

Similar Messages

Maybe you are looking for