Recent bRAS Profile Change - Router Stats

Hai!
Recently, my IP profile has been dropping consistently. I was on 3000 bRAS profile not too long ago (I think I had 5000+ sync in the test socket once).
Since this Edinburgh outage, my profile has been dropping every few days with no disconnections. I decided to put the hub in my test socket last night and let the hub settle overnight before I posted the results here. My sync has gone up, but I don't understand the noise margin etc... Can any techie types give me any clues as to what may be wrong with my connection? Are these current stats OK in the test socket, which would point towards my internal wiring being at fault? Are these current stats showing a problem with my connection in the test socket, which would point towards an external fault?
Any help would be greatly appreciated. Thanks in advance.
Connection information
Line state
Connected
Connection time
0 days, 11:17:49
Downstream
2,944 Kbps
Upstream
448 Kbps
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.1
Latency type
Fast
Noise margin (Down/Up)
15.8 dB / 19.0 dB
Line attenuation (Down/Up)
47.0 dB / 27.0 dB
Output power (Down/Up)
18.1 dBm / 11.9 dBm
Loss of Framing (Local)
0
Loss of Signal (Local)
0
Loss of Power (Local)
0
FEC Errors (Down/Up)
0 / 0
CRC Errors (Down/Up)
107 / 2147480000
HEC Errors (Down/Up)
nil / 1
Error Seconds (Local)
93

Here are my speedtest.bt.com results. My IP profile still hasn't gone up since last night. I understand it can take up to 72 hours to reconfigure:
1. Best Effort Test: -provides background information.
Download Speed
675 Kbps
0 Kbps
1000 Kbps
Max Achievable Speed
Download speedachieved during the test was - 675 Kbps
For your connection, the acceptable range of speeds is 200-1000 Kbps.
Additional Information:
Your DSL Connection Rate :2944 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 750 Kbps
2. Assured Rate Test: -provides background information.
Download Speed
116 Kbps
0 Kbps
600 Kbps
Max Achievable Speed
Download speedachieved during the test was - 116 Kbps
For your connection, the acceptable range of speeds is 576-600 Kbps.
Additional Information:
Assured Rate IP profile on your line is - 600 Kbps

Similar Messages

IP/bRAS Profile Stuck

Hello
We believe that the IP/bRAS profile is stuck on our phone line. We had it replaced about 5 weeks ago after it was damaged in adverse weather. Before our line was damaged, we could get between 3 and 4 Mbit downstream. However, it has been almost five weeks and our line is still sycned at 1152kbps, where the router is showing the maximum attainable rate at 5104kbps, almost 5 times faster!
We have attempted to get in contact with BT - however phone calls and email exchanges with their call center suggest that they are not equipped to solve the problem - instead being repeatedly asked for my operating system and web browser.
Any help on here would be much appreciated!
Downstream
Upstream
Line Coding(Trellis):
On
On
SNR Margin (0.1 dB):
225
68
Attenuation (0.1 dB):
485
288
Output Power (0.1 dBm):
0
126
Attainable Rate (Kbps):
5104
952
Path 0
Path 1
Downstream
Upstream
Downstream
Upstream
Rate (Kbps):
1152
920
0
0
Speedtest using: http://speedtest.btwholesale.com/
1. Best Effort Test: -provides background information.
Download Speed
0.87 Mbps
0 Mbps
1 Mbps
Max Achievable Speed
Download speedachieved during the test was - 0.87 Mbps
For your connection, the acceptable range of speeds is 0.4 Mbps-1 Mbps.
IP Profile for your line is - 1.01 Mbps
2. Upstream Test: -provides background information.
Upload Speed
0.6 Mbps
0 Mbps
0.83 Mbps
Max Achievable Speed
Upload speed achieved during the test was - 0.6Mbps
Additional Information:
Upstream Rate IP profile on your line is - 0.83 Mbps

Hello
We have had just over 4 days of consistent connection but no change in connection speed. The router is reporting a maximum sync rate of 5000kbps. We are synced at just over 1000kbps.
Status:
UP
WAN Type:
ATM WAN
Layer2 Interface:
atm7(0/38)
Connection Type:
PPPoA
WAN IP Address:
xx.186.160.91
Subnet Mask:
255.255.255.255
Default Gateway:
217.32.146.72
DNS Server (Primary, Secondary):
213.120.234.14, 217.32.171.21
Internet Up Time:
4Day(s) 02:42:39
Shortcut:
Click here to view all WAN interface's status and troubleshooting information.
Mode:
ADSL_G.dmt.bis
Traffic Type:
ATM
Status:
Up
Link Power State:
L0
Downstream
Upstream
Line Coding(Trellis):
On
On
SNR Margin (0.1 dB):
221
67
Attenuation (0.1 dB):
485
287
Output Power (0.1 dBm):
0
128
Attainable Rate (Kbps):
5060
952
Path 0
Path 1
Downstream
Upstream
Downstream
Upstream
Rate (Kbps):
1152
931
0
0
MSGc (# of bytes in overhead channel message):
59
12
0
0
B (# of bytes in Mux Data Frame):
36
28
0
0
M (# of Mux Data Frames in FEC Data Frame):
1
1
0
0
T (Mux Data Frames over sync bytes):
1
4
0
0
R (# of check bytes in FEC Data Frame):
0
0
0
0
S (ratio of FEC over PMD Data Frame length):
1.0
0.9872
0.0
0.0
L (# of bits in PMD Data Frame):
296
235
0
0
D (interleaver depth):
1
1
0
0
Delay (msec):
0.25
0.24
0.0
0.0
INP (DMT symbol):
0.0
0.0
0.0
0.0
Super Frames:
0
0
0
0
Super Frame Errors:
124
3792
0
0
RS Words:
0
995008
0
0
RS Correctable Errors:
0
0
0
0
RS Uncorrectable Errors:
0
0
0
0
HEC Errors:
31
2808
0
0
OCD Errors:
0
0
0
0
LCD Errors:
0
0
0
0
Total Cells:
965655913
779443683
0
0
Data Cells:
482117947
53863151
0
0
Bit Errors:
0
200625
0
0
Total ES:
115
2777
Total SES:
0
0
Total UAS:
33
33

How to request bRAS profile reset - persistently s...

Hi,
After four months of messing about, I am approaching desparation. I have been a BT ADSL customer at my current address for over 10 years, throughout that period, I have consistently had around 3.5 - 4 Mbps download speed, occasionally slightly faster. Around January, my speed dropped considerably to around 1.
I initially linked this to some engineering works at the end of my road, where Openreach have installed (but not activated) a fibre cabinet. However, my speed has never returned to normal. Following several bewildering and frustrating conversations with the call centre, I have essentially replaced all my internal telecoms wiring and have installed an ADSL splitter faceplate on the master socket - which my modem is plugged into.
I would post line stats, but I can't get them. I don't have a BT HomeHub (I still have my Voyager modem in a cupboard somewhere) but rather use a TPLink Modem in bridge mode to a WD Router. This kit doesn't give information re: SNR etc. The best I can do is use the BTW Performance Test at http://speedtest.btwholesale.com/ which shows:
Download Speed 2.41
Upload 0.37
Ping Latency 50.75
I have tried the "Further Diagnostics" option hundreds of times, and it never works. "An error occurred while trying to retrieve additional details..."
I have managed to establish from a Freola line quality test that I don't suffer from lost packets, and Jitter is low, (1-2)
I have left all my equipment switched on without reset for weeks, in the hope that the line would auto-adjust back up, but it doesn't.
Is there any way to request a bRAS profile reset without more agonsing conversations in broken english telling me to unscrew my faceplate, plug into the test socket etc? I appreciate that it might make no difference, but I have exhausted all other options.
My exchange was due for a FTTC upgrade by the end of 2014, then it was the end of April 2015, now it's apparently by the end of the 2015 calender year. I'm not holding my breath, but if it's engineering works at the exchange that have caused the problem - it would have been nice to have been informed...
Exchange: Kirkbride LCKKB
Cabinet: 3
Thanks
Solved!
Go to Solution.

Hi davetc,
Welcome and thanks for posting. I’ll be happy to lend a hand with this. I’ll need to run a few checks so can you please drop me an email with your details? You’ll get the ‘contact us’ link in my profile.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

IP Profile changed from 7Mbps down to 2Mbps

Not sure what's going on but my IP Profile has changed overnight. It was slightly over 7Mbs but has dropped to 2Mbps. I have contacted BT about it but am getting nowhere. Can someone here help please, as far as I can see the profile needs resetting by BT were less than helpful when I asked for them to do this?
Solved!
Go to Solution.

This is for the moderator.
Hi many thanks for your help. It's 8.30AM 9 May, unfortunately nothing seems to have changed since you reset my IP yesterday so far, so my IP profile is still 2Mbps. My router has been left on since last Thursday and it seems ok. Router stats and speed test results from today below. I have also done everything asked by BT since last Thursday that is I have changed the filter for a new one, and tried using cable connection. I have tried phoning BT since but I was left on hold, last Friday and yesterday for 18 minutes.
I have also noticed that my Internet usage seems to have trebled from what is the norm which for me is around 7GB per month. I have used 4GB already this month. I have no wireless security issues and have changed my password. I don't know if this ties in?
regards Rob

Profile change please.

Hello,
Can the BT guys please change my profile SNR to 7, since I asked for fast path it has been stuck on around 9.
I was with BE before and a SNR of 7 ran without problems for over 5 years and its only cause of Sly taking over that I moved. Thanks.
router stats:-
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
3 days, 13:33:40
Downstream:
9.118 Mbps
Upstream:
1.101 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Fast
Noise margin (Down/Up):
9.8 dB / 5.9 dB
Line attenuation (Down/Up):
33.1 dB / 17.7 dB
Output power (Down/Up):
20.4 dBm / 12.6 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
6143 / 363
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
12178 / 663
Error Seconds (Local/Remote):
3164 / 171

Hi
I am sorry to see you are having problems
I suggest you contact the forum mods they will be able to get your noise margin reset to the default 6dB for you this is a link to them http://bt.custhelp.com/app/contact_email/c/4951
They normally reply by email or phone directly to you within 3 working days they will take personal ownership of your problem until resolved and will keep you informed of progress
They are a UK based BT specialist team who have a good record at getting problems solved
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

BRAS PROFILE STUCK - MISERY

I had a problem on my line a week ago. Openreach engineer visited. SWitched the wire from the street box, so that the signal comes through a new wire, not the 1970's original. Switched the route my broadbands gets from Exchange to the box. Hardware all seems to work fine. But speed is abysmal! (Worse than dial-up). Here's what www.speedtester.bt.com shows...
Download speedachieved during the test was - 37 Kbps
For your connection, the acceptable range of speedsis 50-250 Kbps.
Additional Information:
Your DSL Connection Rate :10566 Kbps(DOWN-STREAM), 440 Kbps(UP-STREAM)
IP Profile for your line is - 135 Kbps
The throughput of Best Efforts (BE) classes achieved during the test is - 2.7:32.43:64.86 (SBE:NBEBE)
This seems fairly clearly to point towards the IP Profile (I believe called the BRAS profile?) being set too low. This number hasn't changed all week. I have asked BT on about ten occasions to change the BRAS limit. Usually the people at 0800 111 4567 don't understand what a BRAS profile is.
How do I get BT to raise the BRAS/IP Profile? Or, is there likely/possibly another issue? Is there a number I can call where someone will actually be able to help?
Solved!
Go to Solution.

Well, the allotted time passed... and BT are still unable to deliver broadband (
AS at 8.05am:
Download speedachieved during the test was - 49 Kbps
For your connection, the acceptable range of speedsis 50-250 Kbps.
Additional Information:
Your DSL Connection Rate :10566 Kbps(DOWN-STREAM), 440 Kbps(UP-STREAM)
IP Profile for your line is - 135 Kbps
Have requested a MAC code, maybe SKY can deliver.

Stuck IP/Bras profile

I'm a BT customer. My line syncs at over 6Mbps with an IP profile of 5.5Mbps at a target noise margin of 6db which is great for a long line with 55db line attenuation registered on my Billion router. I can reliably download at over 5Mbps so I'm happy - so far so good.
My neighbour but one, (also a BT customer), asked my advice as her connection was very much worse - she was syncing on her Home Hub at 2.88Mbps down & 0.45Mbps up, with an IP profile of 2.5Mbps and a target noise margin of 15db and a similar line attenuation to me so I looked at her internal extension wiring and noticed there was a lot of it with lots of microfilters, so I fitted her an ADSL filtered front faceplate to her NTE5 master socket, removed all the microfilters and told her that the high target noise margin was probably the result of noise on the extension wiring interfering with the ADSL service and after ten days or so of a solid connection it should reduce, (the line was nice and quiet on a silent line test with no evidence of errors in the router stats). This hasn't happened - the line is still stuck at a target noise margin of c.15 dB and obviously is achieving well below its true potential, (tested at 6db target using a Billion 7800N router). She has contacted BT customer help and to cut a long story short, they don't want to know and refuse point blank to reset the IP/Bras profile to allow the line to find its new level following the faceplate replacement. All they do is quote an unrealistically low line sync speed of 600Kbps as the "guaranteed minimum" and say they can't help any further. Needless to say, her currently low download speed results in very poor performance when trying to stream video.
What on earth can a customer do in this situation? Why should she put up with a sub-standard service because BT refuse to perform what is presumably a simple remote reset operation? She can't go to another ADSL supplier as there is no local unbundling and she would be still stuck with the same BT local end and there is no fibre in the area so she is stuck with an unnecessarily inferior service in a monopoly situation.

Hello,
I am the retired neighbour but one that bobbear refers to and like him I'm a BT customer. Bob has volunteered to try and help me solve the problem of my poor broadband speed. I have been unable to get any help over the issue with BT telephone customer support despite providing all of the information requested below which Bob tells me shows a stuck target signal to noise margin which does not reduce no matter how long the router is left connected. (Rebooted yesterday, but had been running for weeks before that). The hub is connected via ethernet to the PC.
Bob has fitted an ADSL filtered faceplate to isolate the extension wiring which he says may have been the cause of the original high target S/N margin, but the margin remains stubbornly stuck, stopping my line from achieving its true potential. (Two doors away Bob achieves a line sync rate over 6Mbps and downloads at over 5Mbps with a default target S/N ratio of 6dB).
ADSL Line Status
Connection Information
Line state:   Connected
Connection time:   0 days, 13:41:22
Downstream:   2.719 Mbps
Upstream:   448 Kbps
ADSL Settings
VPI/VCI:   0/38
Type:   PPPoA
Modulation:   G.992.1 Annex A
Latency type:   Interleaved
Noise margin (Down/Up):   13.9 dB / 19.0 dB
Line attenuation (Down/Up):   51.0 dB / 27.5 dB
Output power (Down/Up):   18.9 dBm / 12.4 dBm
FEC Events (Down/Up):   9734503 / 54
CRC Events (Down/Up):   6 / 7
Loss of Framing (Local/Remote):   0 / 0
Loss of Signal (Local/Remote):   0 / 0
Loss of Power (Local/Remote):   0 / 0
HEC Events (Down/Up):   20 / 5
Error Seconds (Local/Remote):   45 / 19
BT Wholesale Speed Test Results:
1. Best Effort Test: -provides background information.
   Download Speed
   1.93 Mbps
0 Mbps   2 Mbps
Max Achievable Speed
Download speed achieved during the test was - 1.93 Mbps
For your connection, the acceptable range of speeds is 0.4 Mbps-2 Mbps.
Additional Information:
Your DSL Connection Rate :2.78 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
IP Profile for your line is - 2 Mbps
Is it possible to get the target S/N margin reset to the normal 6dB default?
Can someone please help me with this?

2meg BRAS profile

No Phone line for 2 months 6 engineer visits £30 spent on mobile phone calls to BT help centre finally got the line working today and stuck on a 2 meg BRAS profile.
Been sat on the phone to Bt for 40 minuetes and the guy just wont listen, telling me its a fault with the line the engineer say the line tested perfectly
Any got any ideas? is there another number to call
ADSL Line Status
Connection information
Line state:
Connected
Connection time:
0 day, 00:00:14
Downstream:
8,128 Kbps
Upstream:
448 Kbps
ADSL settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Fast
Noise margin (Down/Up):
10.1 dB / 20.0 dB
Line attenuation (Down/Up):
21.0 dB / 11.0 dB
Output power (Down/Up):
19.8 dBm / 12.2 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
0 / 0

Could you please edit your subject, and put it back to the original, as you seem to have changed it. I have corrected it in my post.
Your connection time is only 14 seconds, why is that?
You must leave your home hub turned on and connected to your phone line for at least five days.
During that time, do not reset or disconnect it, even to do a speed test.
If your download speed has not increased after that time, then return to this thread for assistance.
Thank you
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

IP SLA Default Route state down to much

Hello,
I am attempting to use IP SLA trackers to dynamically set the default route going out over a DSL connection. if the sla trackers are down the default route learned from the WAN will take over, but normally we want to send internet/default route bound traffic out over the DSL connection.
ip route 208.67.220.220 255.255.255.255 1.2.3.4
ip route 208.67.222.222 255.255.255.255 1.2.3.4
ip route 0.0.0.0 0.0.0.0 1.2.3.4 track 3
track 1 ip sla 1
delay down 60 up 60
track 2 ip sla 2
delay down 60 up 60
track 3 list boolean or
object 1
object 2
ip sla 1
icmp-echo 208.67.222.222 source-ip 1.2.3.5
threshold 1000
frequency 10
ip sla schedule 1 life forever start-time now
ip sla 2
icmp-echo 208.67.220.220 source-ip 1.2.3.5
threshold 1000
frequency 10
ip sla schedule 2 life forever start-time now
the issue we are having is if the SLA threshold is breached, it immediately sends the trackers into a delay down state. the tracker delays down for 60 seconds, then very quickly comes back up. What we want to accomplish is only if the sla tracker has breached the threshold or is down for 60 seconds, then put the tracker into a down state.
Thanks.

The configuration seems to be correct: IP SLA change as soon as the icmp fail but the tracker delay should ensure the it changes its state after 60seconds of icmp failure. Do you experience a different behaviour ?
What I'm worried about is that, after the default router through the WAN is in routing table, the ip sla ping will be successful and therefore the static route
ip route 0.0.0.0 0.0.0.0 71.32.39.46 track 3
will be used but, at that point, which is the path to 71.32.39.46 ?
Another thing is that, in case of DSL link failure, this configuration will not automatically revert to WAN link because 71.32.39.46 will be still up and running, isn't it ?
Let me know,
enrico

Set up Signal Express to log when there is a change in state of the inputs (NI USB-6501 logger)

Hello NI Forum, I have recently purchased digital I/O logger NI USB-6501. This arrived with Signal Express, which I intend to use as a Lite version. I just wondered if it was possible to set up Signal Express to only add a log entry when there is a change in state of the inputs? I have this working on a 0.1sec sample period and can interrogate the logs after recording. Most of the time nothing will be happenning, I just wondered if there was a way to reduce the ammount of data captured? Cheers.

Ah that unfortunate, and yes start/stop conditions for loging are part of the Full version of SignalExpress
Here's the comparision: http://www.ni.com/labview/signalexpress/purchasing-options.htm
Sorry about that

Bras profile...Help please

My broadband IP profile has been stuck at 135kbps for 10 days or more now. 2 engineer visits , 1 broadband & 1 phone engineer. 1st engineer thought it was alightening strike (he installed new master socket and got my bras prfile rest....it was fine for a few hours, but the next morning it was back down to 135kbps) and the seconds engineer (for noise on the line) said he had refreshed a few connections....the line is now quiet. But still my Bras profile is at 135kbps my line speed is at 6912 kbps according to bt speeedtester. BT told me my bras profile would be reset over the weekend -it wasn't. i phoned again yesterday to be told -really sorry we will do it manually -it will take 2 hours and staibilise over 24hours, i'll phone you back in 2 and half hours to check everything has been done we can do a speedtester check to make sure its all been done. This was the priority care team, Great I thought finally some progress...........
I got a call 3 and half hours later saying it will take another 24 hours to sort "it" out, when i asked why given i had been made several promises all of which had come to nothing... he said he would phone me back in 15 minutes. He did do this but told me it would actually take 59 hours to be sorted.......... as you can imagine my patience had gone and I asked for an explanation..... I was told the lady who advised me on friday had lied to me (his words not mine)and she would be dealt with. Apparently she was fron line support and just wanted to get rid of the call (again ...his words) . The chap from the priority care team who told me yesterday it would take 2 hours was also a liar, and the chap who told then told me it would take 24hours to fix -which 15 minutes later turned into a 59 hours fix time apparently could be trusted because he was from the priority care team. I'm not convinced......two of them gave me duff informantion, including him....he has offered me ofcom's details. But really writing a lette rto ofcom isnt a solution...I Ijust want a useable service in a sensible timeframe, and given the multiple probelms to know that this time its fixed -cause if there is still a problem how long will it take to fix if i keep having to wait 59 hours?
i gather a bras profile can be rest manually and quickly -so why am i having to keep on waiting. surely if the Bras reset doesn't solve my problem then even in 59 hours i will be back to the drawing board and will have to wait another 24/48 hours for an enginner visit and another 59 hours after another attempt at a fix (another week?) . Apparently BT are helpless as its doen to BTw to reset the bras profile. I understand it is BTw's task but surely this can be done quicker when a problem has been o/s for as long as this one!!! I work from home and a 135kbps connection is pretty much unworkable...any advice ideas?

hub stats (connection dropped again this morning after 23 hours of connection -hence only 2 hours of stats):
Line state Connected Connection time 0 days, 02:22:52
Downstream 6,336 Kbps Upstream 448 Kbps
ADSL Settings VPI/VCI 0/38 Type PPPoA
Modulation G.992.1 Annex A Latency type Interleaved
Noise margin (Down/Up) 15.9 dB / 23.0 dB
Line attenuation (Down/Up) 30.6 dB / 18.0 dB
Output power (Down/Up) 10.0 dBm / 1.6 dBm
Loss of Framing (Local/Remote) 0 / 0 Loss of Signal (Local/Remote) 0 / 0
Loss of Power (Local/Remote) 0 / 0 FEC Errors (Down/Up) 11 / 0 CRC Errors (Down/Up) 9 / 5 HEC Errors (Down/Up) 6 / 0 Error Seconds (Local/Remote) 7 / 1
BT speedtest at 8.30 this morning just after line dropped
Test1 comprises of Best Effort Test: -provides background information.
Download Speed
119 Kbps
0 Kbps
250 Kbps
Max Achievable Speed
Download speed achieved during the test was - 119 Kbps
For your connection, the acceptable range of speeds is 50-250 Kbps.
Additional Information:
Your DSL Connection Rate :6336 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 135 Kbps
If you wish to discuss these results please contact your ISP.
If you are experiencing problems with specific applications, servers or websites please contact your ISP for assistance.
Your test has completed please close this window to exit the performance tester.
Please visit FAQ section if you are unable To understand the test results.

ISDN doesn't change to state up - only after reboot

Hi,
i've a router 2801 with the card VIC2-2BRI, i've this problem:
when i plug-in in ISDN cable on the BRI interface the interface BRI doesn't change the state to up, it seems that the cable is not connected.
I need to reboot my router with the ISDN cable plugged in, and when the router starts, the BRI interface is active.
anybody know how to solve this problem?
This is my ISDN bri configuration:
network-clock-participate wic 3
interface BRI0/3/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
isdn incoming-voice voice
isdn bind-l3 ccm-manager service mgcp
isdn sending-complete
voice-port 0/3/0
output attenuation 10
echo-cancel coverage 32
no vad
compand-type a-law
cptone IT
it use MGCP protocol to comunicate with my callmanager.
thanks in advance,
Claudio.

Try:
http://www.cisco.com/warp/public/793/access_dial/ddr_dialer_profile.html
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/800/800swcfg/provisio.htm

Stuck bras profile

Hi,
I am hoping someone can help as I am getting nowhere on the 0800 111 4567 number.
Been on BT broadband for a few years, always beena fairly good connection average around the 4-5mbps. Around about 10 days ago I saw a distinct change for the worse. I have a friend who works at the exchange and sure enough there is some work going on so I thought nothing of it. 2 days of fluctuations and I raise a ticket.
Did all the usual tests with no change. Did my first speedtester under instruction and got:
Download sp.edachl.v.d during the test w,i 1894 Kbps
For your connection. th. acc.ptabl. range of speds.s 400-2000 Kbps.
Your DSL Connection Rate :2663 Kbps(DOWN-STREAM), 699 Kbps(UP-STREAM)
IP Profile for your line is - 2000 Kbps
I said at the time my profile is wrong as surely that limits what I get. The guy agreed 5 hours later I have a profile of 24mbps and download test at 11mbps!! Happy days.... so happy i did not get a record....doh.
Anyhow next am:
Download speedSachieved during the test was - 2005 Kbps
For your connection, the acceptable range of speedsSis 400-2000 Kbps
I Your DSL Connection Rate :4543 Kbps(DQWN-STREAM), 1211 lCbps(UP-STREAM
Another phone call - and my equipment is at fault - again I say it is the profile - few hours later:
7150 Kbps Max Achievable Speed
Dovnload .pe.dachleved during the test s- 3974 Kbps
For your connection, the acceptable range of sp.edss 1000-7150 Kbps
Your DSL Connection Rate :4543 Kbps(DOWN-STREAM), 1211 Kbps(UP-STREAM)
IP Profile for your line is - 4000 Kbps
Acceptable but it drops off again, numerous phone calls - diagnostics etc - even agreed to have an engineer here and he tested line fine to the house his test adsl modem is syncing at 4500 - which is exactly what speedtester was showing the profile at the time.
So I call up again and I can not get angry with the people on the phone as they are limited to what they can do but damnit it is so frustrating. Anyhow long story long, I find out my case has been closed; so I have to start again only to find that today it looks like the line was reset this am, low and behold:
Download Speed 356 Kbps
IP Profile for your line is - 500 Kbps
As with much that is networking I am thinking a reset at the exchange probably warrants a reset at this end so I restarted my hub. The hub has synched at:
Downstream 12,164 Kbps
Upstream 1,167 Kbps
Connection time 0 days, 2:41:49
Speedtester
Download Speed 356 Kbps
Your DSL Connection Rate :12164 Kbps(DOWN-STREAM), 1167 lCbps(iJP-STREAM)
IP Profile for your line is - 500 Kbps
To whomever I have upset, I apologise, please reset my profile.
I can see some of the mods on here have got involved with the bras profiles could you please look into the case?
Can I do it officially via the forum or do I email somebody seperatly?
Any help appreciated.
Cheers
Ju

Hi,
Maybe my apology worked last night. As it looks like it has been reset again - at approx 2am:
Connection time 0 days, 8:29:56
Speedtester shows:
Download speedachieved during the test was - 7189 Kbps
For your connection, the acceptable range of speedsis 2000-21000 Kbps.
Additional Information:
Your DSL Connection Rate :12172 Kbps(DOWN-STREAM), 1176 Kbps(UP-STREAM)
IP Profile for your line is - 10000 Kbps
The throughput of Best Efforts (BE) classes achieved during the test is - 9.99:26.99:63.03 (SBE:NBEBE)
These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
The results of this test will vary depending on the way your ISP has decided to use these traffic classes.
Which is great just a shame it has taken 10 days, an engineers visit to my house and approx 4 hours of helpdesk phone time, and god know how many emails back and forth BT side - seems like a waste of effort if it was purely a profile issue.
Fingers crossed it stays this way, thanks again for the replies.

Network address as the next hop address in ip route statement???

Hi All,
I am confused about ip route statements in the following Cisco document.
Configuring ISDN DDR with Dialer Profiles
Document ID: 9568
http://www.cisco.com/warp/public/793/access_dial/ddr_dialer_profile.html
The statements are;
ip route 172.22.0.0 255.255.0.0 172.22.80.0
ip route 172.22.80.0 255.255.255.0 Dialer1
Why does it use network address as next hop address on the first line?
And it is a source network address on the second line.
Please suggest me.
Thanks a lot,
Nitass

When you specify a network address as next hop in a ip route statement, the router does recursive lookup. When it matches a packet for a network other than 172.22.80.0, it will match the router 172.22.0.0 and the route basically says use 172.22.80.0 as the next hop. Now the router looks up the routing table for how to reach 172.22.80.0 and ends up routing via Dialer 1.

Hhub2 router stats

Where on the Hh2 do you find the router stats ?
Ta,
djh22

djh22 wrote:
I've just moved to BT and I was wondering what the stats were on the hhub2 compared to my Netgear 834g and strangely there is a difference in downstream connection, Netgear reports 8034 and Hhub2 reports 7127.
I have a dect phone connected to the Hhub2 I wonder if it accounts for the difference.
My Netgear always sync'd at a higher speed that the HHub which is why I threw the HHub away. Netgear will give you better control over port forwarding etc.
The important speeds are not the sync speeds which always show higher than reality (maybe that's why they show them in the hub) the important one is the IP profile which is the max that your connection will handle and can only be found at http://speedtester.bt.com
BW 10 days is a myth to keep you out of the helpdesk's hair. It all happens in the first two or three days once connected.
..... Jarviser's Home Hub Index

Recent bRAS Profile Change - Router Stats

Similar Messages

Maybe you are looking for