Set a User Status for Quality Notifications only if they are "Activated".

Hello experts:
I need to be able to set a User Status for Quality Notifications only if they are "Activated".
When defects are recorded for an inspection lot, a "Defect Notification" is created which can be activated to become a "Quality Notification".  Initially, the only difference between the inactive "Defect Notification" and the active  "Quality Notification" is that  the system status DEFR is active for the "Defect Notification", but is cleared when the notification is activated.
So, I'm looking for the business process associated with the Activation to use as a trigger for my own user status.
I checked the business rules for status DEFR and found that the following processes clear this status
  PMM1 -  Postpone Notification
  PMM2 -  Put Notification In Process
  PMM3 -  Assign Order
  PMM6 -  Put Notification In Process Again
Any Ideas ?

Perhaps some additional information would help you understand what I need to do.
For notification type F3, we are recording all defects found in production.
Most of these are expected defects that result in a minor reduction in yield.
For this type of defect, we do not activate the notification, and the inspection lot is closed automatically at the end of production.
However, sometimes defects are observed of an unexpected type or a higher than expected quantity.
When this happens we manually activate the notification and assign tasks to find and correct the cause.
It is only for these activated notifications that I want to automatically set a user status, which among other things, will prevent the notification from being closed until some other actions are complete and a different user status is selected.
The function of the user status currently works exactly as I want, but if it is set as the initial status for all F3 notifications, it is also preventing the un-activated defect notifications from automatically closing.  I therefore want to use the Activation event as the trigger to set my user status.

Similar Messages

  • User status for quality notification

    Hi All,
    from which table we can get user status for a particular notification which is  active status.
    Thanks in advance

    Hi,
    You need to get the OBJNR(object number) for the notifications and then use the FM: STATUS_READ.
    This FM will give you list of all the status or only active status( Set ONLY_ACTIVE = X in FM)..
    Hope this helps
    Regards
    Shiva

  • BAPI/FM for setting the user status for the Project definition and WBS elem

    Hi,
    I have to set the User Status for the Project Definition and the WBS elements in that project.
    The User status to be set is the same for the project and wbs elements.
    Please let me know if there is any BAPI/FM to set the user status..
    Thanks in advance.
    Regards
    Shiva

    Hi Shkithija,
    There is a dump encoutered in the form "PS_FLAG_GET_GLOBAL_FLAGS" for 'chk_precommit_ok' in the "BAPI_PS_PRECOMMIT".
    But it is showing SY-SUBRC = 0 when used along with BAPI_TRANSACTION_COMMIT.
    May i know what are input parameters we need to pass it to "BAPI_PS_PRECOMMIT".
    Do you have any idea.
    Please let me know
    Regards
    vishnu

  • Update System Status for Quality Notification

    I have a program that completes a Quality Notification.
    I would like to know if there is a bapi, badi or function module to change the system status before I complete the notification. When I click on the icon in the notification to complete it, a pop up box comes up to change the status to NOTI or NOTE. I would like to do the same in my program before I complete it.
    Any help would be appreciated.
    Marianne

    Hi,
    You need to get the OBJNR(object number) for the notifications and then use the FM: STATUS_READ.
    This FM will give you list of all the status or only active status( Set ONLY_ACTIVE = X in FM)..
    Hope this helps
    Regards
    Shiva

  • Set User-status for PP order

    Hi All,
    How can I set the user-status for a PP order, also let me know which user exit suits this requirement, as I know I have to make use of a FM or a BAPI which sets the user-status in the user-exit somewhere.
    Thanks
    Mark

    Hi,
    Try the following enhancements/exits for setting the status for PP order.
    STATTEXT
    CCOWB001
    COIB0001
    Regards,
    Anji

  • User status for Notification and Work order

    We generate Service Notification IW26. I have already configured user status like PMND (Planning order not done), AWOP (Awaiting ordered parts) etc. in the Work order a while ago. Now the user wants same User status to the Notification as well. I like to know from experts what is the value added to have the same user status for both Notification and Work Order?
    Do you have any suggestions?

    Hey Chandra,
    The customer intent behind this requirement must be to check in reporting / List Display Transaction about the Order Status. If they want to know looking at a Pending Notification List about the Order Status, you can always provide similar report using SAP Query Builder or with help of your Developer.
    Apart from that If the Requirement is to have these User Statuses in Notification itself, Please advice them that it will be extra activity while performing transaction.
    I dont see any other benefit of having User Statuses added to Notification as well.
    Do let me know if you have some more info on Why Customer is requesting this....
    Regards,
    Avi

  • User statuses for equipment,functional location,order,notification

    Kindly suggest me which user statuses should be assigned to equipment,func. location,notification & order.
    Regards,
    Vivek

    Vivek,
    There is no rule or std instruction which user status to be assinged to equipment,FL, Notification or order. In std you may get some user status for equipment. notification etc. It doesnt mean that you should use it. User status are define /created base on the  business requirement . a user status can be assigned to multiple object type such as equipment, notification ,order etc.
    You can refer the std user status profile when you create your own. In order to know the detail of it object type. You can select the status profile >> click on the detail>> click on the object types.
    Hope it is helpful to you.
    if you want further detail please revert.
    DP

  • User Status for process orders

    Dear Experts,
    We are using user statuses for process orders & with this we are resricting or allowing certain business transactions.
    My question is can we automatically set the two consecutive user statuses ?
    Means when the GR for process order is done i have set the user status as GR.
    Next user status is CLSD.
    So after completing the closing of process order by settlement transactions can i set the staus as CLSD automatic?
    I am trying to do it but i am getting error as-
    "Status CLSD is not allowed (ACT 30000292 0010)"
    Your help is highly appriciated
    Regards
    Vivek

    Hi,
    1) Still your order is carrying cost, it has not settled properly
    2) you can check in CO02 itself, Go to tool bar at top
    3) here Go to > Costs > Analysis & check whether order is set to Zero
    4) you can check in KKBC_ORD also
    Also, pls refer below link
    Re: HOW automatic order status change to CLSD
    regards,
    Sankaran

  • Status profile for Quality notification

    I want to restrict users untill notification is approved, they can not do it complete
    Dear All,
    I want to restrict users untill notification is approved, they can not do it complete.
    I have created status profile through BS02 as ZQM02 where 3 status no I have given:
    10-INIT>Init status checked>lower limit-10 higherlimit-20>Position 1>priority>1
    20-APPR>Init status not checked>lower limit-10 higherlimit-20>Position 1>priority>1
    30-COMP>Init status not checked>lower limit-10 higherlimit-30>Position 1>priority>1
    Allowed Object types>Quality Notification checked
    In transaction control Complete notification marked as forbidd.
    But it is not working, I can still mark as complete without marking it approved.
    status screen also not changing even after completion of notification, it still showing
    under status no 10 >INIT
    Plz advice what I am missing and how I can do this.
    regards,
    sp shukla

    OK. I think you are confused 2 things.
    First.. you have to create 2 kinds of status profile. One is for notification and another is for task.
    Second.. 'next action' means not next transaction. It means automatic set when the transaction is excuted.
    Try below.
    1) status profile 'A' for notification (select 'quality notification' only for object type)
    10-INIT-initial-forbid 'complete notification'-nothing other transaction
    20-APPR-allow 'complete notification'-set 'put in process(released)' (this means a notification will be set 'APPR' automaticaaly when you release a notification and user can complete it.)
    30-COMP-set 'complete notification' (this means a notification will be set 'COMP' automatically when you complete it.)
    2) status profile 'B' for task (select 'task' only for object type)
    10-INIT-initial-nothing other transaction
    20-REL-forbid 'delete task'-set 'release task' (this means a task will be set 'REL' automatically when you release a task and user cannot delete it anymore.)
    3) assign both in configuration
    'A' for notification
    'B' for task
    Regards
    Luke

  • Need help on to set User status for Operations in Maintenance order

    Hi experts,
    i am new to PM module.
    i need to do BDC for IW31. i want to know some inforamtion
    on user status for each opertaion.
    my problem is ,, what is user status.
    why it is saying order is not yet released when saving and status can not set.
    in this cases how can i do BDC.

    User status are something set in the configuration and specific to the company which SAP hasn't given in the system status.
    May be in your system user status are configured to set only  after the release of the order.
    For doing the userstatus you may need to release the order, you can release the order thru bdc and then do bdc for user status. Also see below link
    http://www.sap-img.com/plant/user-status-set-date-in-maintenance-order.htm

  • User status for Notification

    Hi all, I want to change the user status NOCO(Notification completed) for M2 type of notification in the Quality client.I did it in Dev client for M2(Break down Notn) and imported the TR to Quality.When i try to assign this status in Quality client, the system is throwing an error as follows.
    Status NOCO is not allowed (QNF 10039901).   Solution please.Also provide the path in SPRO.
    Thanks in advance,
    Venu.

    Have you completed all of the tasks in the notification. Has the Notification the following system status : ATCO ,
    If not, you would not be able to complete the Notification. Try Completing all the tasks and then mark the Notification as Complete.
    If you have defined any user status to be NOCO, then check that whether in the User status profile, against the current user status of the Notification, the lowest and Highest columns allow the NOCO status or not. Include the status number for NOCO against the current user status. This would solve the problem.
    Path for User Status Profile Creation and Assignment:
    SPRO>Plant Maintenance and Customer Service>maintenance and Service Notifications>Notification Processing>User Status For Notifications-->Define Status Profile
    Edited by: Usman Kahoot on Jun 1, 2010 5:19 PM

  • PM order for set/reset  user status

    I have one requriement like this I need to update the user status for  many operations  of single PM order at a time when user sets or resets the status. Kindly let me know is there any function module or any bapi for this or can you suggest me how to proceed with the further actions to handle this.
    thanks in advance for your help.

    Hi Jaya,
    Before i tell you the FM, there is something u must know about changing the user statuses in PM.
    User statuses are sequential in nature. Eg, if current user status is 15 and you want to set the new status to 30, you must set it to 20, then 25 and then finally 30.
    For this you must first fetch all the valid statuses for the PM order depending on its status profile.
    Next, call the following FM repeatedly each time passing the next status number in sequence until you reach the desired status number:
    'STATUS_CHANGE_EXTERN'.
    Hope this is helpful.
    Thanks,
    Sonal

  • Maintain User Status for Maintenance Order

    Hi,
    I want to maintain User Status along with System Status. For that i have created a user profile for Maintenance and can view and modifiy define user statuses on the Maintenance Order. I have define following three statuses.
    - Created
    - Released
    - Completed
    Initially "Created" status is set on the Maintenance Order but so far i am unable to configure system to automatically change the status into "Released" when the order released and change it to "Completed" when the order is tech completed.
    In short, how to link business transactions with the User defined statuses?
    Regards,
    Shah

    Hi,
    Thanks Dhavan, it was really helpful..
    My requirement was to have a report on Maintenance order in terms of only three statuses "Created" , "In progress" and "Completed" to have a Pie Chart view of maintenance orders. The problem i was facing was that System Status shows multiple statuses depending upon the sequence of the business transactions conducted on the maintenance order and ultimately it ends up creating serveral statuses depending upon the sequence of actions performed on the order. That is why i opted to go for User Defined Statuses. And i linked those statuses with my Business Transactions i.e. like whenever i Release the order it automatically sets my User Status to "In Progress" and now i can have the report as per my requirement.
    Regards
    Shah

  • How to add new actions in customization setting of user status ?

    Hii All
    I am tring to use user status for blocking the creation of new breakdown notification if one breakdown ntification is already pending on it. I want to set equipment under Breakdown status on equipment  when breakdown notification created on it, but when i check for setting the action in user status customization setting, cannot locate the create notification there action there & also cannot add the same in it.
    Can any body tell me how new action can be added there??
    Regards

    Makarand Gurjar,
    You won't be able to do this with user-statuses.
    See your other [VERY similar post|Blocking of Equipment for Notification creation;
    PeteA

  • How to restrict manual setting of User Status?

    Hi,
    I have created an User Profile where a particular User Status is "set" based on the Business Transaction "Release".
    However, we are also allowed to set this User Status manually without carrying out the Business Transaction "Release".
    How do I restrict manual setting of those User Statuses that are "set" based on a Business Transaction?
    Raj

    Pete,
    I did read that post. But it is about providing authorisation to set a Status for an User.
    The case I am referring is, an User Status is auto set by a Bus. Trans Release. But I am also permitted to set the status transition manually. This way, Users tend to skip Releasing the Service Order. This is affecting upstream processes.
    Is there a way where we can restrict manual setting of User Statuses that have to be normally auto set by Bus. Transactions?
    Raj

Maybe you are looking for