Telnet Error code 56 with Telnet Line Client Example?

Using Labview 8.5, XP, Telnet Line Client, I get the following error 56, TCP Read in Telnet Buffered Read.vi->Telnet Read.vi:3->Telnet Line Client.vi.
I looked up this error which looks to be a Networking error: 56 The network operation exceeded the user-specified or system time limit.
The data does seem to return properly but this has been an ongoing issue with previous Telnet clients we are using.

Hi ShotSimon,
You may want to refer to this KB. The Telnet Listen.vi uses the TCP Listen.vi. I hope that helps!
Mike Lyons
National Instruments
http://www.ni.com/devzone

Similar Messages

Error Message with multiple line

Hi
How to display a error message with multiple line?
Example
     Goods movement not possible for material 101
     Goods movement not possible for material 102
     Goods movement not possible for material 103
is it possible is ABAP? If so please advice me.
Best Regards
Asheek

Hi Anoop,
You can use same thing like this
I suggest write ur message through this.
First set the obecj.
CALL FUNCTION 'APPL_LOG_SET_OBJECT'
for local memory
FUNCTION 'APPL_LOG_WRITE_MESSAGES'
         EXPORTING
              OBJECT              = OBJECT
              SUBOBJECT           = SUBOBJECT
              UPDATE_OR_INSERT    = UPDATE_INSERT_FLAG
         TABLES
              MESSAGES            = MESSAGE_TABLE
         EXCEPTIONS
              OBJECT_NOT_FOUND    = 1
              SUBOBJECT_NOT_FOUND = 2
              OTHERS              = 3.
the call for physical memory
CALL FUNCTION 'APPL_LOG_WRITE_DB'
In this process you only need to provide the Itab with error messages.
Reg,
Arpit

Telnet error (Code: 62)

I'm running VIs (LV8.6) under TestStand 4.1.
The
following message is from a Telnet Read/Write vi. I usually open the
Telnet connection at the beginning of the test and close it at the
end. Sometimes there is a gap of long time without any telnet
activity. I set the timout of the Telnet connection to 1 hour.
Any idea what this error mean?
------------------------------- Run Time Error ----------------------------------------------------
A Run-time error has occurred in step: Remove All clocks Priorities
Sequence: Select_TMU_input
SequenceFile: D:\views\quad3_HLXC1536\NPI\TESTER\Work\HLXC1536\Seq\HLXC1536.seq
Error
Message: TCP Read in NI_InternetTK_Core_VIs.lvlib:Telnet Buffered
Read.vi->NI_InternetTK_Core_VIs.lvlib:Telnet
Read.vi:1->TelnetReadWrite.vi->TelnetReadWrite.vi.ProxyCaller
Error Code: 62
Thanks
Rafi

The error code means:
The system caused the network connection to be aborted.
It's possible that the device you are telnetting into is timing out and closing the connection. In general I find it much more relaible to open a connection, use it, and then close it before long periods of inactivity.
Mike...
Certified Professional Instructor
Certified LabVIEW Architect
LabVIEW Champion
"... after all, He's not a tame lion..."
Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

Create log entries with command-line client?

I am getting an error message that seems to indicate that it's impossible to create log entries with the command-line client. Can I ask one of you FCS gurus to advise me?
Note the disturbing error message below: *Entity /log doesn't know how to do create*
root# ./fcsvr_client create /log --xml < /tmp/logentry.xml
<?xml version="1.0"?>
<session>
<values>
<value id="CODE">
<atom>E_NOTSUPP</atom>
</value>
<value id="DESC">
<string xml:space="preserve">Entity /log doesn't know how to do create</string>
</value>
<value id="SRC_FILE">
<string xml:space="preserve">PmdEntity.C</string>
</value>
<value id="SRC_LINE">
<int>2017</int>
</value>
<value id="ERROR_TYPE">
<atom>ET_PERM</atom>
</value>
<value id="ADDRESS">
<string xml:space="preserve">/log</string>
</value>
</values>
</session>
root# cat /tmp/logentry.xml
<?xml version="1.0"?>
<session>
<values>
<value id="LOGASSETID">
<string xml:space="preserve">26</string>
</value>
<value id="LOG_DETAIL">
<string xml:space="preserve">I am your log entry detail.</string>
</value>
<value id="LOG_STATUS">
<string xml:space="preserve">OK</string>
</value>
<value id="LOG_TYPE">
<atom>response</atom>
</value>
<value id="LOG_USER">
<string xml:space="preserve">admin</string>
</value>
<value id="LOG_SUMMARY">
<string xml:space="preserve">Log Summary from Command-Line</string>
</value>
</values>
</session>
Message was edited by: dpotter-ntc

Hmm, no, my 1.5.2 instance logs script responses twice- once to say it is executing and again after the process terminates to say that it ran. The second entry is where any stdout is printed. I don't know of any setting that would turn this off, it has always been there for me.
A typical script response log entry looks like this:
Summary
"response \[Response Title] script triggered by Subscription \[Subscription Title] complete"
Detail
"response complete, completed command /fcsvrbin/\[scriptname.sh] with arguments { 43, 8 } "
"stdout would print here, if there is any"
You probably already tried it, but try filtering your log search for "script triggered" since it can be easy to miss spotting entries on a busy system, and they don't necessarily show up side by side in the logs with the other responses in their respective stack.

How to catch the error code thrown by Oracle client installation?

Hi everyone,
Recently, I'm writing a bat file to install Oracle 11g client for windows, I know the command line should be below, but how to find the error code it return? like the command line I want to run in Windows, the errorlevel will return 0 if the command line is pass, otherwise it will return no-zero:
oui.exe -silent -waitforcompletion -nowait -force -responseFile ...\response\clientruntime.rsp
BTW, I know I can find the error info under the path ...\Oracle\Inventory\logs, but I think it is better if you can tell me another way to catch the error in command line. I just wish that I can determine whether the Oracle provider installation is pass......
Thanks
Lindsay
Edited by: lindsaywang on Oct 6, 2008 1:28 PM

I got it.
Thanks,
TD

Error: Tables with Header line No longer Supported In WD-ABAP

Hi folks,
           I am working on WD4A functionality.I have to use Abap code to retrive data from database and i am doing it by declaring internal table with header line in one of the Methods.I have to do manipulation on table before i can bind table to result node.I can do manipulation in Header in ABAP,but now it is no longer supported in WD4A.What can i do for this?
Nirad.

hi nirad.
The example is not of much sense
but explains the funtionality. Hope this is what you are searching for.
data:
         lt_flights    type table of sflight.
data:
         ls_flight     type sflight.
select * from sflight
into corresponding fields of table lt_flights.
loop at lt_flights into ls_flight.
ls_flight-price = 1000.
modify lt_flights from ls_flight.
endloop.
Cheers,
Sascha

The camcorder displays an error code with the letter C: or E: followed by a number.

Solved!
Go to Solution.

Error codes display to help diagnose issues detected by the camcorder. Below is a list of common error code numbers, followed by their causes and the necessary steps to resolve the issue.
IMPORTANT: If model-specific information is required to complete any of the steps in this solution, refer to the operating instructions supplied with the product. Manuals are available online in the Manuals/Specs/Warranty section of the Sony® eSupport Web site.
NOTE: The xx in the error codes below represent any random numerical digits and does not affect the overall diagnosis of the issue.
Error Code
Cause
Resolution
C:13:xx
The recording media you are using is either not supported for use with the camcorder or the media has a problem.
Ensure the recording media you are using is supported for use with the camcorder or try using different recording media.
NOTE: If you have a DVD camcorder and are using a recordable DVD, the disc may be dirty or have scratches; try cleaning the disc with a soft cleaning cloth.
C:21:xx
Moisture condensation has occurred.
Remove the recording media from the camera.
Leave the media compartment open for at least one hour.
Insert different recording media into the camcorder.
Power on the camcorder.
C:22:xx
The video heads are dirty.
Clean the video heads using a dry head-cleaning cassette.
C:04:xx
C:23:xx
The battery being used is not an InfoLithium® battery.
Replace the battery in the camcorder with a Sony® InfoLithium battery or connect the supplied AC power adapter.
C:31:xx
C:32:xx
The camcorder has detected an issue that may require a power reset.
Turn off the camcorder.
Remove the battery or disconnect the AC power adapter for 60 seconds.
Insert the battery or reconnect the AC adapter.
E:20:xx
E:40:xx
E:60:xx
E:61:xx
E:62:xx
E:91:xx
E:94:xx
The camcorder has detected an issue that may require service.
Reset the camcorder to factory specifications to try resolving this issue.
The troubleshooting steps listed above should resolve your issue. If you have completed all of the steps and the issue is not resolved, service may be required. The Sony® eService Web site at https://eservice.sony.com/ can assist you in obtaining service from a Sony Service Center or locating a Sony Authorized Servicer.

Error Code with Livecycle forms, when opened online - how do I fix this?

Could you please tell me how to fix issue where when I make my forms available online, they open up with an error code? I provide a link to a file, and when the user opens the file, it says there was an error - about a paragraph of text. If they save the file, and then open again in Adobe Reader, it works fine. But most of the time they think the file is corrupt, and don't want to download and save it to their computer. Below is a screenshot of the problem, and it only happens when I open the file online. And, I have already upgraded to the most recent version of Adobe, so why does this happen?

Oh, I found a great instruction page at Configure browser to use the Adobe PDF plug-in That worked! Thank you!

Error code with itunes

Hi
I am in the process of resetting ipod touch 32gb. I was told to update our version itunes to itunes 10. It is now on our computer. I then had to restore my ipod. It downloaded overnight. when i try to set up my ipod there is a picture on the ipod touch which implies connect to itunes ( cable to itunes icon on display) Ive done that then when I open itunes and click on the device after a short time an error code -9808 appears and says we could not complete your itunes store request and try again later. When I turn on the ipod it only shows the connect to itunes display
any ideas pls

I'm having the same problem as well. I can't see to get any support from Apple on the phone. I've been on hold for 20 minutes.

Error code with download of application manager

Error code A12E1
What does this mean?
I can't complete downloading the adobe application manager because the message suggests I contact customer support.
How can I fix this please?
Bianca

Try the direct download links for AAM found in this article
http://helpx.adobe.com/creative-cloud/kb/download-error-403-launching-aam.html

I am wondering why I cannot empty my trash. I keep getting an error code with 8003. Does anyone know how to solve this problem?

Hi, I just want to know how to empty my trash because I keep getting this message saying " The operation can't be completed
because an unexpected error occured (error code-8003) I tried looking this up and couldn't find any refference regarding it.
Please help

Please look to the right of the screen where it says "More Like this" you may find the resolution there.

M4E Error Codes with SBS/Exchange...

Hi,
Does anyone have a list of the error codes for Mail for Exchange?
I have a Nokia E61 and I am trying to link it to our SBS Server. The SBS server supports RPC/HTTP, so I know all the domain certs/settings/passwords are good.
The E61 also access the Internet via WiFi, so I know this works too.
However, after installing and checking everything I can - I see this in the error log, two error codes I dont seem to be able to find answers to anywhere!
All help most welcome!
08/05/2007 7:28:46 OffPeakTime active
08/05/2007 7:28:50 Mail For Exchange Error -30180
08/05/2007 7:37:47 Profile Updated
08/05/2007 7:37:49 OffPeakTime active
08/05/2007 7:37:50 Profile Updated
08/05/2007 7:37:51 OffPeakTime active
08/05/2007 7:37:54 Mail For Exchange Error -30207
08/05/2007 7:38:15 Setting ROAMING status to True
08/05/2007 7:38:24 Mail For Exchange Error -30207
08/05/2007 7:38:50 Profile Updated
08/05/2007 7:38:52 OffPeakTime active
08/05/2007 7:38:53 Profile Updated
08/05/2007 7:38:54 OffPeakTime active
08/05/2007 7:38:55 Cancel job:3,type1:
08/05/2007 7:38:58 Mail For Exchange Error -30207
08/05/2007 7:40:35 Profile Updated
08/05/2007 7:40:36 OffPeakTime active
08/05/2007 7:40:39 Mail For Exchange Error -30207
08/05/2007 7:41:06 Mail For Exchange Error -30207
08/05/2007 7:57:53 OffPeakTime active
08/05/2007 8:09:44 Setting OFFLINE Status to True
08/05/2007 8:40:39 Mail For Exchange Error -30180

Help, I need somebody Help, not just anybody Help, you know, I need someone Help
When I was younger (less IT smart,but arrogant), so much younger than today I never needed anybody's help in any way But now these days are gone, I'm not so self assured Now I find, I've changed my mind, I've opened up the doors (i really am stuck!)
Help me if you can, I'm feeling down And I do appreciate you being 'round Help me get my feet back on the ground Won't you, please, please help me? (this M4E error is killing me!)

Error #2037 with no line reference

Hello, its me again:
I am working on my mp3 player and all is well up to when
the current song plays or the user stops the song (stop() is
called and song position is set to 0). The externalInterface
is working, at least for the first time the user clicks play button.
However, if the song is finished or the user clicks a stop button
and tries to play the same song again the following error occurs:
Error: Error #2037: Functions called in incorrect sequence, or earlier call was unsuccessful.
    at flash.media::Sound/_load()
    at flash.media::Sound/load()
    at player_fla::MainTimeline/playSound()
Since there is no line number reference, it is unclear where the code is
breaking down, beyond <soundObj>.load(urlRequest) (??)
Once the selection is stopped or finished, does it have to be reloaded, or
does it persist in memory? (Is there a way to explicitly remove it from memory
and then reload it again?)
Thank you for time and attention, suggestions.
JK

I solved this problem: there was an erroneous branching condition
in the playSound() function that was causing the condition to always
run the initial code and not the restarting code when the sound was
already loaded. But it was a matter of feeling around in a dark room.
JK

How can I print source code with connecting lines on control structures?

Anyone know of any programs that will format source code printouts and print connecting lines from the start to the end of control structures (such as: if--"end if", while-"end while" etc.)?

Indentations and comments do help read source code. However, when you have a large program with many levels of nesting of control structures the readability of the code (even with indentations) becomes very difficult.

Error code with HP DesignJet T520 ePrinter

Good day everyone, recently I had a customer drop off this machine for service. It is of a type I am completely unfamiliar with. Apparently the machine spends most of its time in a hard shell storage case in a warehouse and is only used when the group has to leave the area and travel elsewhere. They are leaving in a few weeks and pulled this machine out to ops ck. it. Upon power up, the machine shows the HP loading screen and then goes to a bluescreen. At the top there is a box of some sort that shows up in white that looks like a corrupted image. Below this is the message "805DE431". This message does not clear up with a power reset, unplugging it from the wall or anything else. I have searched the internet and through the service manuals and find no mention of an error message like this at all. Has anyone ever encountered something like this and can provide me with a direction of where to look? Thanks for any help anyone can provide.

Please, Turn on the printer and open the door ink. Check if a green LED behind the Main PCA is flashing. If a green led is not flashing, is possible that the Main PCA and Bundle Board should be replaced by onsite customer engineer.

Telnet Error code 56 with Telnet Line Client Example?

Similar Messages

Maybe you are looking for