Total failure officejet 6700

after place new cartridge printer doesnt work

Hello there,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I am sorry to hear that you are seeing a failure message on your Officejet 6700 after you installed a new cartridge. I have a couple of suggestions for you to hopefully help.
1. An 'Ink System Failure' Error Message Displays on the Printer or on the Computer
2. A 'Cartridge Problem,' 'Ink Cartridge Failure,' or 'Incompatible Ink Cartridges' Error Message Displ...
If the issue still persists after you are done troubleshooting, I would then suggest calling HP's Technical Support to see about replacement or trade in options.
If you are calling within North America, the number is 1-800-474-6836 and for all other regions: click here.
Take care,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Similar Messages

Hp officejet 6700 premium printer-printer failure

I bought a HP officejet 6700 premium a month ago. I installed the printer and it printed ok. But after a few day of use, it suddenly stopped printing and gave a Printer Failure massage on the front control panel. The message says: There is a problem with the printer or ink system. Turn printer off then on. If problem persists, contact HP. I have checked all ink cartridges. They seem all ok (I have only print less than 10 pages since installed). I have turned power off and on several times but did'nt work. I have searched all over the HP website for help, but still can't find a solution for my printer problem. I deeply appreciate, if someone can help me or give me directions to make my new printer works again. Thanks.
P.S. my laptop computer has Winders 7.
ns42

Did you get an answer? I think the problem lies with the blue print head with the gold pins, they get bent when you change out printer cartridges. Several folks have had this problem. I watched a youtube video of repairman saying both the 6600 and 6700 printer had this problem until HP changed the print heads. I am still fussing with HP about this but I am pretty certain I won't get any relief. Good luck

Officejet 6700 Premium says color cartridge is depleted and won't print at all

My printer is only 5-6 months old, and refuses to print because it says the Yellow cartridge is depleted. I know it has not dried up and that it is still printing fine because I signed up for an app that prints out recipes every weekday (in color) and the page printed just this morning looked perfectly fine - the yellow showed up totally normal. The estimated ink level for the yellow cartridge does say that it is depleted, but how can that be when I have proof (from this morning's printout) that I still have yellow ink? And, according to the manual, the printer will still print if one of the color cartridges is depleted, as long as the black is not depleted. The black is only half-used, so why is the manual giving false information and my printer still refuses to print anything? Very frustrated....

Hey BoydJones, I see you are having an issue with your Officejet 6700 Premium and have a few questions. There are 2 major types of ink systems for inkjet model printers: IPH (integrated printhead) and IIC (individual ink cartridges). Many older model printers used the IPH style cartridge system: Tri-Color and Black. Most newer printers use the IIC system, but not all. There was a reason for the paradigm shift in the ink systems. The tri-color cartridge contained all 3 colors used in color printing: Cyan, Magenta, and Yellow. If any one of the 3 ran out, then you had to replace the cartridge no matter how much of the other 2 remain in the cartridge. In the IIC system one can change only the individual color that is out. As to the reason your color is draining from what appears to be little color usage: The printer uses ink in many ways. Ink is used when cleaning the printhead to ensure proper performance in print jobs, a small amount of color ink is placed below black ink to ensure a full rich black color and a long lasting printout, and ink is used to perform other preventative maintenance in the printer. For more information on how ink is used in HP printers please click here. The reason one has to change the cartridge in the IIC style ink system is to prevent damage to the printhead of the unit by ink drying in the ports of the printhead. The printhead in the 6700 premium is a stationary/permanent printhead and any damage of this nature could prevent the unit from printing at all. In the 2 cartridge, IPH, system the printhead is contained with the cartridge and replaced with each cartridge change. Thus, if one runs out of color and waits to replace the cartridge there will not be an issue of dried ink in the ports as the printhead is changed with the cartridge. I hope this helps to explain and clarify. As well, I saw your post and forwarded it to the right people for their review. You should hear back from someone shortly via private message on this Forum. Jason

How do I re-enable built-in networking on Officejet 6700 premium printer?

I inadvertently, and stupidly, turned OFF the built-in networking from within my Officejet 6700 premium AiO web-based administrator console. Now I cannot manually reset it from the controls on the printer itself. I get a message informing "Built-in network capabilities have been disabled. Contact your network administrator or the person who set up the printer." Well, that person is me. I cannot find instructions telling how to re-enable the built-in network capabilities.
My OS is WIN7. The printer was working OK before I messed with it.
Can anyone offer advice regarding this problem?
Thank you.
This question was solved.
View Solution.

Distinquished (and snarky) Professor.
Thank you for your attempt to assist, but your response was not only condescending - "Did you read the manual??? I downloaded it and read it. Turn the wireless radio on and off" - but totally not helpful. The intro to your reply makes you sound to be an arrogant high school teen who thinks she has every answer unknown to adults.
Some of us are not technilliterate. I certainly DID read the manual and attempted every option I thought might work. The problem, if you read my problem post, was that I inadvertently clicked OFF the Connectivity Built-in Network capabilities from within the EWS. That made it impossible for my printer to connect to the network via cable or wireless. When I attempted to find a solution at the printer control display itself, by going Setup > Network > Restore Network Defaults, but, instead of the "Restore Network Defaults, it presented the message I posted informing that Built-in network capabilities were disabled, which is what I already knew and wanted to resolve. I needed to find a way to reset to Out-of-the-Box settings. Nothing in the manual provided, nor could I find online, this answer.
Fortunately, my printer was still under warranty (HP apparently wont chat if you aren't under warranty, unless you pay them for the service). I was able to chat with an HP Rep who Identified herself (maybe himself ... Who knows?) as "Jasmine". Jasmine was very helpful. But, although I had specifically identified to her the problem is that I lost network connectivity due to carelessly turning off built-in network capabilities of the printer from within its EWS, Jasmine still had to spend time running through her HP requied first-line Help Representative script. She spent about fifteen minutes remote assisting and checking out every possible "other option" before she concluded with these precious words, "The problem is that your printer has lost network connectivity. I am going to give you some instructions to follow so we can reset the printer to Semi-full restore." I received her instructions and followed them precisely. Very easy. When I asked her why these instructions are not published by HP somewhere for customers to access, she informed that they are "secret Advanced instructions" (I think she was being a little silly). ...
Following, for you Distinquished Professor (so you don't need to be snarky with others) and for all other fellow technophiles out there, is Jasmines "secret Advanced instructions" as she wrote the on the chat. I have provided some interpretation at the end. Do note, if you (not specifically you Distinguished Professor, but every other "you" out there) don't have some good idea of what you are doing, getting off the path by which these instructions lead can get you into more difficulty with your printer than that by which you began the journey.
Jasmine: Please follow the below steps:
1. Touch this curve icon 4 times though it is not highlighted
2. When you do it, you can see Support menu on the printer LCD screen.
3. Once you see the Support Menu on the printer touch OK use the right arrow key next to the printer LCD screen to see Reset Menu.
4. Now, touch OK then use the right arrow key next to the printer lcd screen to see Semi Full.
5. Touch on Semi-Full option.
6. The printer will turn OFF
7. Power it back ON. It will initialize itself.
8. Please follow the onscreen steps.
Helpful interpretations:
Regarding #1. The “curve icon” is the left curving return icon located at the left side of the printer’s control panel touch sensitive display window, but outside the display window. It is lit when the menu can be returned back a page, but unlit when at Home screen. This is actually a hardware button, not touch sensitive, so pressing it, even when not lit, creates and action signal. When the display is at the Home state, the return button is unlit, but pressing it four times will generate a menu option for Support Menu on the display.
Regarding #3. The "right arrow" is the forward page button located to the right outside the display screen. Like the return button, it also is unlit unless it can perform an action related to what appears on the display. Press the forward page arrow until the displayed menu option changes to Reset Menu. Select this option to perform step #4.
Successfully following Jasmine's instructions will restore the HP Officejet 6700 Premium AiO to its out-of-the-box-new settings. Note that Jasmine specified "Semi-Full" restore, not "Full" restore. A full restore will take the printer back to it basic out-of-the-factory state. This state will require significantly more settings and configurations work afterward than with which most of us would like to deal. Out-of-the-box state will cycle through everything as it did when you first pulled the printer out of the box new and set it up yourself. Do note, any custom settings will be lost. Passwords, however, are retained in a Semi-Full restore.
Hope this information helps everyone else who may be having similar difficulties or just need to know how to restore your printer back to Out-of-the-box-new state.

Officejet 6700 error while searching for updates: 'Printer could not connect to server'

I recently purchase the Officejet 6700 Premium. While setting the printer up, I received the error 'The printer could not connect to the server.' I first received this while the printer was searching for updates. I later received the same error while trying to set up ePrint from my computer.
The printer is connected through my wireless router. All other print services function normally. It is connected to the network, and I have printed several times over the wireless network.
Though I don't think it matters, since the on-board print set-up gave me the error, I run Windows 7 64-bit on my computer.
Thanks for any help!

What is the IP address of the printer? What is the make and model of the router that you use in the wireless set up? Is the router firmware up to date?
I would first try power cycling the router and the printer. Turn off/unplug the router and then power down the printer. Then plug the router back in and wait for it to be fully up and functioning before turning the printer back on. After you have both pieces of equipment back on and functioning attempt to connect to web services again.
If still having problems I would attempt to set a static DNS on the printer through the embedded web server (EWS) by entering the printer's IP address into the address bar of a browser on a computer.
Once that computer displays that page click on the Network tab.
Then look in the column to the left and find the Wireless section
Click on IPv4
Then on that page look at the 2nd section that is labeled DNS Address configuration
Change the radio button to the manual option
Then for the manual preferred fill it out and make sure it reads 8.8.8.8
Secondary should be set to 8.8.4.4
Then hit Apply
Read the next screen carefully. That message with the "OK" button below it is one that states to click that button to undo the changes you just made. Just navigate away from that page by clicking on another tab.
Then reattempt to connect to web services.
I am a former employee of HP...
How do I give Kudos?| How do I mark a post as Solved?

OfficeJet 6700 Premium Problems after Windows 8.1 update

My Officejet 6700 Premium worked great wirelessly under Windows 7 to print & Scan. Since updating to Windows 8.1, I can print to the printer wirelessly (having set it up manually from the printer), but the software won't load and I can't scan. Setting up a network connection using downloaded HP software fails (it just says it failed, no error message), and trying to download the entire software package (which includes scan, which I need), also fails during step 1 of 4. I tried uninstalling all HP software first, but the same errors persist. I don't want to mess things up further (as I said, I'm able to print wirelessly now), but I really want to be able to scan to the computer. Any help would be appreciated.

Hello mfrank1,
Welcome to the HP Forums.
I see that you are having some printing issues since you upgraded to Windows 8.1.
I do have a few troubleshooting steps that we can try to resolve this issue.
I first suggest that we uninstall the old software and drivers. I realize that you have already attempted to do this but I still would like to try it again but this time using the following document: Uninstalling the Printer Software.
When you stated that you have the printer connected with a direct connection using wireless, is this with a Bluetooth connection? Do you have a Router that you are going through?
Once the software is uninstalled, please restart the computer. Please disable any firewalls or anti virus protection before starting the next step.
When the computer is back up and running, please click on the following link for the HP Officejet Full Feature Software and Driver.
Please save the download to the Desktop of the computer so that it creates it's own Icon. Double click on the new Icon and follow the instructions.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thank you for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

HP Officejet 6700 - scanning problem, "device is busy. please try again later"

I am using a windows laptop (Lenovo Yoga II). I have an HP Officejet 6700 printer/ scanner. The printing functions seem to work fine but the scanning function is now not working at all (worked previously).
When I use the HP Scan and Capture app is comes up with a message "Device is busy. Please try again later". I have installed the full software and also run the HP Print and Scan Doctor and it fails the driver check even after a full restart of both printer and laptop.
I have tried everything wirelessly and also connecting the laptop to the printer via USB and nothing seems to work.
When I try to scan direct from the printer/ scanner to the computer (ie. using the panel on the front of the printer) it recognises the computer but doesn't scan and suggests that the "scan application on the computer is currently in use".
I have McAfee LiveSafe running and also tried switching that off but didn't seem to make any difference.
Any ideas welcome. I really need to scan some things today and this is very frustrating.

Hi,
Please follow this HP document for scan issues
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03092457&tmp_task=solveCategory&cc=us&dlc=en&la...
hope this helps
Although I am an HP employee, I am speaking for myself and not for HP.
*Say thanks by clicking the "Kudos! Star" which is on the left*
Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue.

Scanner not working hp officejet 6700

I have an Officejet 6700 Premium Printer.. When I hit scan to computer, it says no computer found. I connected the printer to the computer with a USB cable and hit scan but window says waiting for scanner.. Printer works wirelessly w/ computer but is sporadic and sometimes have to restart printer to get it to connect wirelessly to computer.. tried to download software from hp but cant open the dmg file in my download file. Error message says Officejet series 6700 image not recognized.

Hello ramblindan,
Welcome to the HP Forums.
I see that you are having an issue with scanning to the computer.
I also see that you had the printer connected on a wireless network and then attempted to scan over USB. When the connection is changed from wireless to USB without adjusting the software, this can cause communication issues.
I have a few steps that we can run through to troubleshoot the issue.
First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
I also suggest that we remove the usb cable from the printer and the computer and leave it off.
Please click on the following link that troubleshoots when the Printer Does Not Maintain Wireless Connection.
If this does not resolve the issue, please respond with which Operating System you are running.
Which Windows Operating System am I running?
Mac OS X: How Do I Find Which Mac OS X Version Is on My Computer?
Thank you for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

OfficeJet 6700 - "Unable to communicate with printer" message after install

I am on a hybrid network with Windows 7, 64-bit. Printer is hard-wired to the router (ethernet) but laptops are wireless. Installation doesn't allow for a hybrid option, just wireless or wired, so I installed as wired.
I just installed the OfficeJet 6700 - installed OK. I also updated software/firmware during the install process.
Windows' "Devices & Printers" recognizes the HP as being installed.
Printer is able to produce the network configuration page, etc. so we know the printer is functional, but when I try to print I get an "Unable to communicate with printer" message.
Windows' "Devices and Printers" troubleshooter thinks the driver is not installed, but as I mentioned, I just installed software from the CD.
UPDATE: I was able to install & print without problems on my wife's Win7, 64-bit laptop. Something about mine seems to be the issue. Also, HP Print & Scan Doctor reports that everything checks out OK, but when I try to print a test page at the end of the good doctor's diagnosis, I am still "unable to communicate with printer."

Sorry this is so long, but I tried to be through in my testing.
Followed your suggested steps.
I had previously set a static IP address, but just to be thorough, re-set it again with the same address.
I unplugged the USB cord from the laptop.
I began with the device labeled "HP OfficeJet 6700 (Copy 1)," which was set as the default printer.
After entering the IP address & clicking Next, it searched the network and returned this message:
Additional port information required
The device could not be identified.
The device is not found on the network. Be sure that:
1. The device is turned on.
The network is connected.
The device is properly configured.
The address on the previous page is correct. (re: the page where the IP address is entered)
If you are sure the address is correct, select the device type below.
I selected Standard (Generic Network Card) and clicked Next.
Summary dialog appeared and I clicked Finish.
Clicked OK/Apply.
Attempted to print. Like before, it sent the file to print queue - then nothing.
Right-clicked on the "Copy 1" device and selected Troubleshoot. Returned the message: Make printer "Fax HP OfficeJet 6700 the default printer" - even though this copy is already the default printer. (Usually when the original copy is set as the default, this copy is automatically re-named "Fax HP OfficeJet 6700.") I chose "Apply this fix."
Summary page said "Troubleshooting has completed." I closed the troubleshooter and attempted to print. I closed the Devices & Printers window so it could refresh. Re-opened Devices & Printers. Now the default printer is named "Fax HP OfficeJet 6700." The other device is grayed out and is simply named "HP OfficeJet 6700."
Attempted to print. (I'm testing w/ Notepad and .txt files)
I have 3 choices in the Notepad's printer dialog box but only 2 devices showing in the Devices & Printers window:
~ "Fax HP OfficeJet 6700" - This is the default printer in the Devices and Printers window. I clicked on Print & rec'd an error message: "Send Fax - HP Officejet 6700. There is a problem communicating with the Printer. Check your USB connection & verify that the printer is ready." Notepad's print dialog box shows status as Offline. I canceled all documents in the print queue.
~ "HP OfficeJet 6700." When I choose this printer option, Notepad's print dialog box shows status as "Paused - Offline." I clicked on "Print" anyway, and like before, it sent the file to print queue - then nothing. This is the printer that shows as grayed out in the Devices & Printers window. I canceled all documents in the print queue.
~ "HP OfficeJet 6700 (Copy 1)." There is no printer by this name in the Devices and Printers window even tho' it shows in Notepad's print dialog box. Notepad's print dialog box shows status as "Ready." In Devices & Printers, when I right-click on the one labeled "Fax OfficeJet 6700" (the default device) and choose "See what's printing," 2 HP devices are listed - the one labeled "Copy 1" and the one labeled "Fax." I clicked on "Print" and like before, it sent the file to print queue - then nothing. I canceled all documents in the print queue.
I plugged in the USB cord again and re-ran the same series of tests.
~ "Fax HP OfficeJet 6700" - This is still the default printer in the Devices and Printers window. Notepad's print dialog box shows status as "Ready." The fax window opened, waiting me to enter the recipient's name, add a cover sheet, etc. I closed the fax window. The .txt file was in the print queue for the "Fax" device, so I canceled all documents in the print queue.
~ "HP OfficeJet 6700." When I choose this printer option, Notepad's print dialog box shows status as "Paused - Offline." I clicked on "Print" anyway, and like before, it sent the file to print queue - then nothing. This is grayed out in the Devices & Printers window. I canceled all documents in the print queue.
~ "HP OfficeJet 6700 (Copy 1)." Again, there is no printer by this name in the Devices and Printers window even tho' it shows in Notepad's print dialog box. This is one of 2 choices in the device labeled "Fax" - the default device. Notepad's print dialog box shows status as "Ready." I clicked on "Print" and like before, it sent the file to print queue - then nothing. I canceled all documents in the print queue.
Next, I used the printer's touch screen interface and turned the wireless connection off, leaving the USB cord plugged in.
~ "Fax HP OfficeJet 6700" - Status: Ready. The fax window opened, same as before. I closed the fax window & canceled all documents in the print queue.
~ "HP OfficeJet 6700 - Status: Paused - Offline. I clicked on "Print" anyway, and like before, it sent the file to print queue - then nothing. This one shows as grayed out in the Devices & Printers window. I canceled all documents in the print queue.
~ "HP OfficeJet 6700 (Copy 1)" - Status: Error. I clicked Apply, then Print. Again, this is one of 2 choices in the device labeled "Fax" - the default device. Like before, it sent the file to print queue - then nothing. I canceled all documents in the print queue.
Reconnected to the wireless network & verified that the IP address had not changed.
Tried again to print using "HP OfficeJet 6700 (Copy 1)" - Status: Ready. I clicked Print and again, it sent the file to print queue - then nothing. This is still listed as one of 2 choices in the device labeled "Fax" - the default device." Like before, I canceled all documents in the print queue.
Next, I right-clicked on the one labeled "Fax OfficeJet 6700" (the default device) and choose "See what's printing" and selected the device labeled "HP OfficeJet 6700 (Copy 1)." In the print queue window, when I click on "Printer, one of my options is "Set as Default Printer." As soon as I did that, the device in the Devices & Printers window was renamed as "HP OfficeJet 6700 (Copy 1)" - no longer named "Fax." I tried to print again. Once again, file was sent to the print queue but never printed.

Officejet 6700 very slow to print does not scan to Imac

I just purchased a new officejet 6700 from Costco it takes at least 10 min to print if at all and does not scan to Imac the current osx is snow leopard 10.6.8 using an airport time machine as a my wireless router / backup I have charter internet with ARRIS modem model # TM502G its also very slow to run any functions in the hp utility I did notice that the home network ip and printer ip are different don't know if that is an issue or not any help would be appreciated thanx.

Hello kennethburland,
Welcome to the HP Forums! I understand your concerns with your Officejet 6700 Premium.
What program are you printing from? Do you notice this issue occur from using multiple program(s)?
Please follow this entire HP document on Slow Printing. Make sure you choose your correct operating system.
You did indicate that your printer's IP address and your home network are different. The first three numbers of the IP address should be the same, but the last number(s) should be different. Please reference this HP document on Wireless Basic.
Are you receiving any error message indicating why you are unable to scan a document to your computer?
If you are receiving a "Connection Error", then please follow this HP document here. If the scanning software isn't responding, then follow this HP document here.
Please inform me your troubleshooting steps.
I worked on behalf of HP.

HP Officejet 6700 Fax not going through

When I try to send a fax, it dials but never connects?

Hi @Carlita61,
Welcome to the HP Forums!
I noticed that the fax is not going through with your HP Officejet 6700. I am happy to look into this for you!
What type of phone service do you have? Analog or digital? Analog. Digital. What’s the Difference?
If the phone service is analog, please see this guide, Cannot Send or Receive Faxes.
If the phone service is digital, please go to this guide, How to connect your HP Fax Device to an ISDN, ADSL, PBX, or VoIP line. Note: HP fax devices are designed to work with traditional analog phone services. They are not designed to work with digital phone services such as ADSL, PBX, ISDN, or VoIP. While HP fax products are not supported on these types of lines, they might work given appropriate setup and equipment.
To find out if your phone service is analog or digital please contact your phone provider.
Hope this information is helpful, and thank you for posting!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Apple devices will not print to Officejet 6700 including MacBook Pro and iPad

I am trying to help someone set up their MacBook Pro and iPad to be able to wirelessly print to their Officejet 6700. I recently set them up with a new Apple Airport Extreme for their router. The printer connects fine to the wireless network. Everything during the install process for the printer goes well, the MacBook easily sees the printer. The correct driver is installed. They also have a Windows 7 laptop that prints instanteously and has no issues whatsoever.
When I try to print from the Mac, nothing prints. I open the print queue and it shows "Printing - connected to printer..." and nothing ever comes of it. When trying to print from the iPad, it can see the printer and I select it. However, after telling it to print, the dialogue box just says "Connecting to Printer" and it never does - it just times out.
Things I've tried:
Everything in this article that is related to Macs (10.8).
Resetting the printing system on the Mac.
Resetting the printer to default settings.
Setting the static IP of the printer through the printer settings.
Setting the IP of the printer through the Airport Utility (after changing the printer to automatic).
Rebooting the Mac after each attempt to remove the printer and before adding again.
Using the official HP Officejet 6700 driver.
Using the Airprint driver.
Other info:
I can successfully ping the printer's IP address from the MacBook Pro.
I can easily see the web setup page for the printer both through the printer settings and by entering the IP address.
The printer is only about a month old.
They bought this printer because the previous one was having problems printing from all of their devices wirelessly. That was with a router from their previous ISP.
At this point, I'm completely stumped as to why the printer will not print from these Apple devices. We've dealt with every issue that could be causing it: the network, the printer, and the MacBook itself. I've looked online and can see no issues with people not being able to print to a wirelessly connected printer to an Airport Extreme. I've seen some issues when the printer is plugged in via USB to the Airport Extreme, but that is not our setup.
Any help would be greatly appreciated!!!!
This question was solved.
View Solution.

Thank you very much for your help @Sunshyn2005!!!!! I think we're good to go now!

Wireless printing problem in home network officejet 6700

1.HP Officejet 6700 Premium
2. not applicable(multiple operating systems. windows 7 and OS Lion)
3. My printer is connected to my house's wireless network and has accessibility to the internet, but when I try wireless printing from my iphone, ipad or macbook pro the printer "can not be seen". Saying " no air printers available".
But if i unplug the printer's power and plug it back in, when it just gets connected to the wireless network again I am able to "see" the printer for a brief moment and thus I'm able to print. But a little while later disappears again.
What can I do?

Hi antoniotineo, take a look at this document for suggested solutions to the problem you're describing. Work down through them in sequence and see how you get on.
Hope this helps you get your problem solved.
If my reply helped you, feel free to click on the Kudos button (hover over the "thumbs up").
If my reply solved your problem please click on the Accepted Solution button so other Forum users may benefit from viewing the post.
I am an HP employee.

Total Failure of CC 2014 Apps on Windows 7

Total Failure of CC 2014 Apps on Windows 7
Yesterday (Thursday16 Oct 2014) I had one of those tech issues that stretch the imagination and patience of a customer. After using CC for the past two years, and generally very happy with the response and resources, I updated all my app to the CC 2014 releases.
I expect a few bugs (which are usually corrected quickly) but not a total failure. In my case InDesign would open, but lock up. It could not be accessed or terminated without using the Task Manager. Illustrator would open and run, but could not be terminated without the task manager. Photoshop worked, I didn't try the remainder of the apps.
I started at 10am trying to figure it out. I deleted all the preferences, cleared CC preferences, reset VRAM, all the usual steps.
At 11a I called tech support and that started what ended up being a four hour cycle of two tech support calls with remote access which produced zero results and plus my time of more than 4 hours uninstalling/reinstalling first the CC2014 apps and then finally uninstalling all CC2014 apps and re-installing the CC apps (but that's the end of the story).
Both tech support personnel were polite. But they took me through and agonizingly long stretch of nothing. It was like a four hour Seinfeld episode.
Before I continue understand that I have, by design, a totally generic machine. It is Win7 64B, 8GB of ram, NVIDIA Video, 4TB of high speed disk drives and standard software. I have GB Ethernet, and Comcast commercial service with 50/15, almost zero latency. The only semi-intrusive component is MS's Security Essentials. All drivers are up to date with the latest or latest stable versions.
Also note that I have been using Adobe products on Mac and PC since 1995 and I have never had an experience like this with any product.
Solutions offered and explored were:
* Increase VRAM to 4x physical RAM
* Make Acrobat the default printer
* Ask if I am on a domain controller
* An a dozen other relatively useless options.
There was a lot of random setting, disabling services, etc. All for nothing. And all the solutions offered were generally irrelevant. Any software that has otherwise worked perfectly for years, that suddenly requires me to uninstall WACOM, uninstall printers, disable services, change network configurations, etc. should be ignored and other options found.
Finally, I told them to stop. I had already lost more than $1500 in billing and I am now two days behind in work. I then uninstalled all the CC2014 apps and re- installed all the CC apps which to no surprise work perfectly.
This is totally unacceptable for a company like Adobe. There is something wrong with the release and I could not get the support personnel to say, "Wow. We better get on this right now." I finally told them I couldn't afford to let them use me to debug their mistakes.
I fear that companies like Adobe, and Apple, and Microsoft are enamored with the speed of online software releases and are getting very sloppy indeed in testing. When they had to burn a million CD installs it seems they were much more careful.
So Adobe, what do I do now? Your mistake has cost me more than the equivalent of two years subscription to CC in just one day. In 24 hours you've effectively doubled my subscription cost (actually quadrupled because I now have to the work and make up the same hours in overtime).
What do I want? Simple...
1. I want Adobe to credit me one year of my CC subscription.
2. I want Adobe to commit to testing as thoroughly as they used to.
3. I want Adobe to fix the CC2014 apps
4. I want to know I can have confidence in future installs.
5. Take away the horrid opening screen on Illustrator CC2014 or let us choose our own images.
// Marco Ciavolino
http://www.meetmarco.com

Have you received any feedback regarding this issue and reasonable resolution?
InDesign CC 2014 is proving to be a mess for me. It will work for a while, then it won't. I can only use the task manager to close the file. I've followed all of the suggestions for disabling, resetting, preferences, settings, etc. I continue to have horribly slow performance, or no performance at all.
Interestingly, I now have an issue with fonts. Fonts installed on my computer work great in one file. In another file, the exact same fonts, with the exact same paragraph and character settings can't be found for some reason. When I attempt to replace the font a prompt displays that the font can't be found. It can be found in another file, very perplexing.
So far today, I've spent three hours trying to make a file change that should have taken me 15 minutes at the longest.
What is going on with this version? This is a ridiculous way to do business. What happened to trouble shooting and caring about the end product? This is frustrating and my confidence in Adobe has been depleted. The company I work for was looking to upgrade to Adobe CC for all 65 marketing and graphics personnel, I can't recommend that now.
Any new information on how to deal with these issues would be greatly appreciated.

BT Phone Line Order – 9 months of total failure – ...

I've been trying to get a phone line and internet connection from BT installed into a London flat since the 07th of January 2012.
This email/letter does not contain every contact with BT in the last 9 months – as I have not kept records of all the dozens and dozens and dozens of calls, texts, and emails but it is a good enough list to show the general theme of total failure from BT in all aspects of both technical and customer service.
(I have re-written this and removed my 5 or so BT account numbers, the various fault numbers, the dozens of VOL numbers and removed any surnames of people in it in the hope that this will get posted.)
07 Jan 2012
Place first order for phone and internet. BT.com reference: <removed for forum post>.
You can only do Mon to Fri installs. My next day available day off work is 19 Mar 2012 so the line engineer’s appointment is made. 8am to 1pm. I am self-employed and it is not easy to take time off work. In fact it costs me money every time I have to take time off work.
19 Mar 2012
The phone line engineer is late. Arrives after 1pm. He looks at job and says he can't do anything. It needs a new line installed even though there is already a line installed? New line involves a cherry picker and another visit by the line engineer. More time off work. New phone is line installed into flat.
27th Mar 2012
I am informed that the new phone line does not work. Order is cancelled? I get no details on what the problem is and why I can't get a line or what to do next. I have no phone at home so I’ve not tried to use the line; yet BT has already cancelled my Order.
I called ‘BT help; somebody tells me the line is connected to the wrong exchange. I spend lots of time and many calls talking to people in India and I think other parts of the UK. People tell me they are going to call me back and don't. I tried to speak to supervisors in India but nobody returns calls. I’m getting nowhere for weeks and weeks. I give up; it all seems too hard…
7th June, 2012:
Over the internet I place a new order with BT for phone line and internet:
Your order number is: <removed for forum post>. Phone number: <removed for forum post>
6th July:
BT infinity engineer appointment. 8am to 1pm. He is late. After 1pm. He arrives, looks at job and says he can't do anything. He says the phone line does not work.
I inform him the order I placed with BT is for a phone line and internet. He says there is nothing he can do as he does not ‘do’ phone lines. Another day off work. Lost wages, lost time.
No phone & no internet.
Fault is raised:
Date closed: 6 July 2012
Fault/VOL number: VOL012-<removed for forum post>
Open Product affected: Phone fault
Telephone number: <removed for forum post>
Lots of calls to BT. But getting nowhere at all. They tell me there is no fault on the line but will send an engineer that I might have to pay for.
8th July:
Phone line engineer arrives 8am to 1pm. He is on time. He informs me all the existing work is incorrect. They have connected all the equipment to the wrong exchange. It should be the Putney exchange but they have attempted to hook me into the Wandsworth exchange - which won't ever work. Still no phone & no internet. He raises a fault number: LS6 W80 <removed for forum post>
10th July:
9am call from Open Reach engineer. This is not a scheduled appointment. I've had no contact from BT. I am at work. He does not know the problem or the fault number. I give him the fault number and call him back 90 min later. He confirms that I have been connected to the incorrect exchange and cabinet? He can't do anything to fix the problem.
I want somebody to call me with a solution.
I don't want to talk with more people in India who can't help me or even understand the problem. How can this be such a failure?
I use website to email in a letter with the entire listing of existing fault details/number, order numbers etc.
Thank you for your enquiry. We will respond to your enquiry as soon as possible. Please make a note of your enquiry reference number and use it in further correspondence.
Your enquiry reference number: 120710-<removed for forum post>"
One of the issues I am finding is that BT does not link previous faults with new ones, or previous Orders with new ones, or previous Customer Numbers with new ones. Every time I speak to somebody they cannot find any details of the history of these problems so far. BT keep on cancelling my Orders and placing new ones; raising new faults etc. But nothing is linked and when I speak to people for help they can’t see any of the history of the line, faults, address, etc.
19th July, 2012:
I get an email from BT. They have cancelled their own Order again.
Order cancelled. Your order number is: BTCAA6<removed for forum post>
Dear Mr HUNTER, We confirm your broadband order's now cancelled.
23rd July, 2012:
Email from BT as they re-raise a new Order:
Your order number is: VOL012-<removed for forum post>
Check out your account and more about your service
Phone line starts(SL-N)
Phone number: <removed for forum post>
24 Jul 2012 before midnight
Track your order - you'll need order number VOL012-<removed for forum post>.
24 July, 2012:
Email from BT as they re-raise a new Order:
Good news Your order number is: VOL012-<removed for forum post>
Dear Mr. HUNTER, Your phone service is ready for you.
BUT IT IS STILL NOT WORKING..
Sometime around this date BT Priority Help gets involved and lots more phone calls ensue.
27th July, 2012:
After I talk to priority help line and say please don’t waste our time anymore with line engineers that come around and say ‘we can’t do anything’.
BT Priority Help book another engineer visit & we need more time off work again.
The next line engineers visits and he says it is the same problem. He says he can’t do anything. He says it is connected to the wrong exchange. And leaves.
He says his manager will call me. Fault Number: LS6 WPE <removed for forum post>
28th July, 2012:
Call from somebody from BT asking about my street address.
They say the address might not be correct.
29th July, 2012:
Next day call from Franz’s, fault line engineer manager.
He says:
A new order is going in.
Equipment might not be installed in correct place. Correct place should be CAB7 PCB 7 Putney.
Some part of the equipment might still be pointing to Wandsworth.
A new order to the exchange is being place to do it all again.
The address BT has for this flat will not be the problem as it is a new line installed by BT.
I need to wait till Tuesday and see if it works.
A New Order is booked; again.
Monday 30th July, 2012:
I call the priority help line and COMPLAIN again that BT are getting nowhere.
I explain that whatever you have been doing since MARCH 2012 to get this line working HAS NOT WORKED. I repeated what one line engineer told me that it might need to be connected to another exchange. Not WANDSWORTH & NOT PUTNEY but one called PUTNEY/CHISWICK???
I explain to somebody from BT Priority Help Care the days and days and days I have lost trying to get a phone line and internet installed into this flat…
I get a call back 30 min later.
Lady on the phone tells me that all the previous 5 orders have been placed with Wandsworth phone numbers. She has created a new Order, Order number 6, and it is an Order with a PUTNEY EXCHANGE phone number because all the other orders have been for a mix of the wrong exchange and all have used WANDSWORTH EXCHANGE phone numbers – which would stop this working even if the line and equipment was connected to the correct PUTNEY exchange…
1st Aug, 2012:
Text message from BT saying they are having "systems issues trying to correct and update data in the background, and exchange problems".
Monday 6th Aug, 2012:
Voice mail from BT priority care team: Informed "Problems with Engineering and Exchange. They will call back on the 08th of Aug."
14th Aug 201:
Emails arriving saying that your new line is now working.
But it is not.
6pm - ish I am called from BT Sunderland priority help care. Lady does not know the details of the case. She tells me the line should now be working.
I explain there isn’t a dial tone.
She tells me there is an address problem. Probably.
I explain the 8 months of issues I have been having.
She tells me to not get upset. She doesn’t know anything about this case.
She tells me “It can actually take up to 12 months to get a phone connected in London”.
She tells me “that it can be very complex to get a phone connected”.
She tells me there is a long winded email attached to my case. I tell her that the ‘long winded’ email she is reading was written by me in an attempt to show all the problems in the last 8 months IN ONE PLACE – something BT seem incapable of doing.
She tells me I have to wait 10 days until the address team finish their address checking.
I explain to her that the line engineers have told me it is not an address problem.
She tells me there is nothing she can do.
28th Aug
BT priority Care called me. Told me that they are still waiting for results from the Address Team.
29th Aug
BT priority Care called me.
Told me that it is connected to the incorrect exchange now. Wandsworth… The same thing I was told last March.
I got ‘annoyed’ and tried, again, to explain the entire story to the lady on the phone.
She told me she cannot see any records of my orders back to January.
She told me that she didn’t understand what the problem is, and that the records they have shown the line was working in Aug...
I asked her to get her manager to call me.
No manager called me; instead I get a call back from the same lady later in the day. She is trying to help but we are still getting nowhere. BT Priority Care are just trying to do the same things again, that have failed multiple times in the past. They have no solution because they do not know what the problem is?
30th Aug 2012
BT priority Care called me; lady might have been called Sharon? Another lady anyway.
She tells me a new order is going to be placed to get the line connected back to Putney.
I ask to speak to her manager. She says she will call me back.
She calls me back and tells me that her manager Kelly W<removed for forum post> a BT Priority Care Manager Sunderland(maybe?) is going to call me before 6pm. This is the 3rd time I’ve asked to speak to a manager at BT Priority Care. Nobody calls me back.
All I get from BT since March are people trying the same failed thing, again and again.
Now they want to check with the address team. Again.
Now 6 months later after getting it connected to the Putney exchange, they want to put it back to the Wandsworth exchange, where it was originally – and never worked? I question this decision? I ask why this is going to fix the problem if it is the opposite advice to what every line engineer (5 of them) has ever said. I get told that nobody can answer that question.
Friday 31/08/2012
Another set of emails and text tell me I have a new line that is working.
But of course it does not. The phone line is dead. No dial tone.
Phone number is: <removed for forum post>
VOL012-<removed for forum post>
Monday 03/09/2012
All the BT priority care line numbers with the PIN numbers I was given have stopped working.
I can’t make a call to get through to the BT Priority Care Team anymore.
So I phone the normal BT help number…
An automated system tells my phone number is on exchange that is having a high level of faults for the last 2 hours and then it automatically disconnects my help call.
I phone back again and I have to NOT give my phone number for about 4 levels of automated systems to get to speak to a person. This time get through to a person. In India.
I ask for help trying to get put through to the Priority Help Care Centre in the UK. I am informed by somebody in India that all BT Priority Help Centres in the UK have been closed for good – since last Friday. I have to explain, again, the now nine months of trying to get a line connected – to the Indian help desk. I told to wait while she speaks to her supervisor.
I get put through to a different BT Priority Help Centre in the UK. Not Sunderland.
I speak to a man. He says he will email the Sunderland Help Centre and Kelly W<removed for forum post> and get somebody to phone me.
I ask him for advice on what I should do to try to get a phone line connected – after 9 months of trying. He says he will try and escalate it but he does not want to step on other peoples toes?
I ask him to CC in the CEO of BT to the email he is going to send to Kelly W<removed for forum post>. He thinks I am joking….
It is Wednesday night of the 04th of September 2012
Still no call back from Kelly or anybody from the Help care team. This is the 4th time I’ve requested a call back.
And now my PIN numbers for the priority call number have been disabled so I can’t call them.
Of course; why would you expect anything less?
LETTERS OF LATE PAYMENT:
In the last 6 months I’ve got multiple letters from BT telling me I am late in paying for my line service. I get ‘account overdue’ letters even though I prepaid the 12 months line service in advance for a line that has never worked.
SADLY:
There are phone lines in the flats below me, either side of me, and all down this entire street.
There are phone lines all over London. There are phone lines all over the UK.
But sadly not one that works in my flat. I’ve been without a phone or an internet connection since I moved in. 9 months ago.
MARS:
The Americans have flown a Mars Rover, which weighs a ton, from the Earth to Mars, landed it, and driven it around a bit – all on another planet - in the same time BT has failed to install a working phone line into a flat in central London? I wish it was this funny..
GIVEN UP:
So now I give up. My endless frustration at BT’s total lack of anything even close to coordinated fault tracking or anything like co-ordinated customer care service isn’t worth the time or stress any longer. 9 months of stress, lost wages while I’ve waited at home for engineers, and countless hours and hours of my time wasted on hold or speaking to people that can’t help.
YOU SUCK:
BT you are the total pits.
I don’t think you could suck more.
Some of my account numbers have been GB 1084 <removed for forum post>, GB 1099 <removed for forum post>, GB 1038 <removed for forum post>, GB 1105 <removed for forum post>
Dozens of other reference numbers: <removed for forum post>

Further onwards (actually downwards or backwards):
I did respond (last week) to the request to contact the forum moderators directly and was told that that they could not help because this is now being referred to Ombudsman.
Thanks for the offer of help anyway.
Two days ago I did receive another letter from BT. Dated after I was told that I would never get another letter from BT asking for payment for something that was never done. "You will never get another bill". I get another bill.
So more, painful, calls to BT in India. Have to explain the entire 9 month situation again. More wasted timed.
Asked to wait while supervisor is contacted.
Told she can't help but I should call this number: 0800 169 4109.
Which I did. But of course that number requires a number and a pin. And they don't give you a pin number. So they have effectively just cut me off.
So I have to start the entire 'call for help about this bill' processes again.
(Don't forget I've been talking to BT now since January 2012. 9 months, coming up to 10 months and I still can't get a working phone line and I still can't stop getting bills for something that has never worked).
Additioanlly on top of getting sent another late payment letter I’ve see no letter regarding the ‘Deadlock’ process between BT and I – as ‘promised’ by BT. I was told, verbally, the letter would go out last Monday. It is still not here. I want to know if the process has began. So I try to get help with that on BT Help Chat.
My goal in the chat below was to:
1. Get help with the Ombudsman process. I wanted to know why I had not received a letter from BT as I was told I was going to on the date I was expecting.
2. Get a phone number to speak to somebody about the Ombudsman process that BT had started.
3. Find out why I am still getting late payment changes for a line that has never worked - in the 9 months since the initial line order was created.
I was not given a number to call for help. Claire, the Help Chat lady, would not give me the number.
I was told I was going to be 'called back,' which I was not happy with as I know from 9 months of past experiences with BT that I will not be called back.
Sadly I was getting very frustrated by the end of the ‘Help Chat’. 9.5 months of tryign to get a phone line working in Central London has left me a little stressed...
Please note that today is the day after the chat transcript below. While Claire was trying to be helpful:
I was not called back. I received no help regarding getting details on what stage the Ombudsman process is at and what I have to do next.
9.5 months now. No phone line. No solution. Lots and lost of endless frustration.
Days and days and days of stress and my own time and hence money wasted.

Total failure officejet 6700

Similar Messages

Maybe you are looking for