VG248 or FXS port pass DNIS to the attached device ?
Hi All,
I have an IP Telephony and unified messaging setup.
Topology:
PSTN--2600--CallMgr---VG248----FaxServer
I need to have dedicated fax lines then I have two options, either use the VG248 or use analog cards in 2600 type of ios voice gateway. I would like to know if both or any of these voice gateways will pass the Called Number (DNIS) to the Fax Server???
Passing the Called Number is important because based on those dialed numbers, Fax server will send the calls to the right mail box.
Your help in this regard would be highly appreciated.
Thanks,
Ahmer Ghazi
The following link explains about Cisco 2600 router acting as fax gateway.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t8/plfxrl26.htm
http://www.cisco.com/univercd/cc/td/doc/product/voice/c_callmg/3_2/sys_ad/3_2_1/ccmcfg/b06gtway.htm
Similar Messages
-
When I plug in my Olympus TG 820 to my iPad2 a message pops up warning me that the attached device uses too much power. Is there a way around this?
1. Turn off iPad
2. Connect camera to iPad
3. Turn on power of camera
4. Turn on iPad -
not able to restore the backup of iphone 5 to iphone 5s , itunes shows a error ager comleting 75 % backup , data is corrupted or not compatible with the attached device , please help me as ther eis important data is saved in the backup.
Restore the device as new, sync the desired content to the device.
-
I bought a Air Port Express device from Apple yesterday. We decided to set the Air port device in a room near the router to use as a wifi extender to areas of the house where the signal is weak. In our discussion with Josh, the Apple Rep. he explained how it can either be connector to the router or use in another room relying on the existing wifi signal to extend it further into the house. We have verizon DSL. Our town is very small...no cable provided so we are lucky to have what we have...some areas of our town can't even get what we have. We, didn't want to connect it directly to the Verizon device (router)....we followed the directions from Josh as well as the explicit directions provided by Apple support...it didn't work. We keep getting an error message. Does anyone have any advice ? Any help would be greatly appreciated. Please speak in "Laymen's terms" I am not technically savy....but..am determined to get this set up. Thanks to anyone, in advance!
Signed,
MEAbeepIn our discussion with Josh, the Apple Rep. he explained how it can either be connector to the router or use in another room relying on the existing wifi signal to extend it further into the house.
Unfortunately, it appears that Josh was not aware that the AirPort Express can only "extend" a wireless signal from another Apple router.
From Apple's literature:
Extend an existing Wi-Fi network’s range.
If you already have a wireless network in your home and want to extend its range, AirPort Express can help. Just place it in range of your primary base station — an AirPort Extreme, Time Capsule, or another AirPort Express — and near the area where you want your wireless connection. Launch the easy-to-use AirPort Utility app on your iOS device or Mac, and you’re mere minutes away from long-range Wi-Fi enjoyment.
The AirPort Express is not compatible with a Verizon product for this purpose.
Your might want to have another conversation with Josh to ask his advice on how best to proceed at this point.
If you do decide to keep the AirPort Express, it will be necessary to connect it to your Verizon router using a wired Ethernet cable connection if you want the Express to provide more wireless signal coverage. -
Multiple FXS ports on a 3745 to the PSTN
Hi,
I'm putting together a spec to have 35 FXS ports routed directly to the PSTN via an ISDN PRI.
Can anyone foresee any issues with doing this with a 3745, fitted with 3 x NMHDA-4FXS + 3 x EM-HAD-8FXS + appropriate PWDM2 mods + NM-HDV-E1 (or AIM-MFT VWIC?) + appropriate IOS image?
This would be a standalone system (e.g, not controlled by a CallManager), and all the phones will need dedicated lines. And each port will need to be able to generate a line reversal signal.
Any input on this would be appreciated.
Cheers,
J.You can go through the following document and check whether the current IOS version supports it .
http://www.cisco.com/en/US/products/hw/routers/ps282/products_data_sheet09186a0080091ba1.html -
Connection PLAR on FXS port 2821
I have an anlog phone that is located by the main gate. The phone has been extended and terminated into an FXS port on a 2821 router. I am trying to configure a connect PLAR on he FXS port, so that when the phone goes off-hook it dials an internal VoIP extension.
I am not having any luck. Any help would be appreciated. My config is below:
voice-port 1/0/5
timing hookflash-in 50 0
connection plar 220005
description North gate
caller-id enable
dial-peer voice 220005 pots
destination-pattern 220005
port 1/0/5
dial-peer voice 100 voip
preference 1
destination-pattern 220...
modem passthrough nse codec g711ulaw
session target dns:CallAgent01
voice-class codec 1
voice-class h323 1
dtmf-relay h245-alphanumeric
no vad
Thanks!!
JaimeYosh - do I need to remove dial-peer voice 220005 pots for the PLAR to work correctly?
Thanks,
Jaime -
To avoid the attachment for the body content while sending email from ABAP
SAP Version : 4.7
When i tried to send an external email from the abap report program, the body content of the mail is coming as an attachment for the same. I need to avoid this. Please give the suggestion. Am attaching the code.
DECLARATION PART *
TYPE-POOLS : SLIS.
TABLES : VBAK.
DECLARATION FOR ALV.
DATA : F_FIELD TYPE SLIS_T_FIELDCAT_ALV,
W_FIELD TYPE SLIS_FIELDCAT_ALV,
L_HEADER TYPE SLIS_T_LISTHEADER,
W_HEADER TYPE SLIS_LISTHEADER,
W_LAYOUT TYPE SLIS_LAYOUT_ALV,
t_sort type slis_t_sortinfo_alv,
w_sort type slis_sortinfo_alv.
TYPES : BEGIN OF T_VBAK,
VBELN LIKE VBAK-VBELN,
VKGRP LIKE VBAK-VKGRP,
KUNNR LIKE VBAK-KUNNR,
ERDAT LIKE VBAK-ERDAT,
VTWEG LIKE VBAK-VTWEG,
LIFSK LIKE VBAK-LIFSK,
VKBUR LIKE VBAK-VKBUR,
END OF T_VBAK.
TYPES : BEGIN OF T_VBAP,
VBELN LIKE VBAP-VBELN,
POSNR LIKE VBAP-POSNR,
MATNR LIKE VBAP-MATNR,
WERKS LIKE VBAP-WERKS,
ARKTX LIKE VBAP-ARKTX,
KWMENG LIKE VBAP-KWMENG,
CUOBJ LIKE VBAP-CUOBJ,
NETWR LIKE VBAP-NETWR,
ZSCHL_K LIKE VBAP-ZSCHL_K,
KONDM LIKE VBAP-KONDM,
ZZURWN LIKE VBAP-ZZURWN,
END OF T_VBAP.
TYPES : BEGIN OF T_LIPS,
VBELN LIKE LIPS-VBELN,
POSNR LIKE LIPS-POSNR,
VGBEL LIKE LIPS-VGBEL,
VGPOS LIKE LIPS-VGPOS,
END OF T_LIPS.
TYPES : BEGIN OF T_KNA1,
KUNNR LIKE KNA1-KUNNR,
NAME1 LIKE KNA1-NAME1,
ADRNR LIKE KNA1-ADRNR,
END OF T_KNA1.
TYPES : BEGIN OF T_VBKD,
VBELN LIKE VBKD-VBELN,
POSNR LIKE VBKD-POSNR,
BSTKD LIKE VBKD-BSTKD,
BSTDK LIKE VBKD-BSTDK,
KURSK LIKE VBKD-KURSK, " CURRENCY CHECK
BZIRK LIKE VBKD-BZIRK, " SALES DISTRICT
KDGRP LIKE VBKD-KDGRP,
IHREZ LIKE VBKD-IHREZ,
END OF T_VBKD.
TYPES : BEGIN OF T_LIKP,
VBELN LIKE LIKP-VBELN,
ERDAT LIKE LIKP-ERDAT,
END OF T_LIKP.
TYPES : BEGIN OF T_ADR6,
ADDRNUMBER LIKE ADR6-ADDRNUMBER,
SMTP_ADDR LIKE ADR6-SMTP_ADDR,
END OF T_ADR6.
DATA : BEGIN OF IT_CUST OCCURS 0,
KUNNR LIKE VBAK-KUNNR,
END OF IT_CUST.
TYPES : BEGIN OF T_VBUP,
VBELN LIKE VBUP-VBELN,
POSNR LIKE VBUP-POSNR,
KOSTA LIKE VBUP-KOSTA,
WBSTA LIKE VBUP-WBSTA,
END OF T_VBUP.
TYPES : BEGIN OF T_TVLST,
LIFSP LIKE TVLST-LIFSP,
VTEXT LIKE TVLST-VTEXT,
END OF T_TVLST.
TYPES : BEGIN OF T_CONFIG.
INCLUDE STRUCTURE CONF_OUT.
TYPES : END OF T_CONFIG.
DATA : TMP LIKE VBAK-KUNNR.
DATA : NAME_TEXT LIKE THEAD-TDNAME.
DATA : TLINE1 LIKE TLINE OCCURS 0 WITH HEADER LINE.
DATA : TMP_BRAKET LIKE CONF_OUT-ATWRT,
TMP_BRAKET1 LIKE CONF_OUT-ATWRT.
DATA : BEGIN OF IT_FINAL OCCURS 0,
WERKS LIKE VBAP-WERKS,
VBELN LIKE VBAP-VBELN,
POSNR LIKE VBAP-POSNR,
KUNNR LIKE VBAK-KUNNR,
NAME1 LIKE KNA1-NAME1,
VBELN1 LIKE LIKP-VBELN,
ERDAT LIKE LIKP-ERDAT,
LIFSK LIKE VBAK-LIFSK,
ZZURWN LIKE VBAP-ZZURWN,
IHREZ LIKE VBKD-IHREZ,
ERDAT1 LIKE VBAK-ERDAT,
NETWR(25) type C,
BSTKD LIKE VBKD-BSTKD,
BSTDK LIKE VBKD-BSTDK,
SALORD(17) TYPE C,
PUMP_TYPE LIKE CONF_OUT-ATWRT,
PUMP_SIZE LIKE CONF_OUT-ATWRT,
VTEXT LIKE TVLST-VTEXT,
KWMENG(25) TYPE C,
FOOTER(330) TYPE C,
ITMTXT(330) TYPE C,
END OF IT_FINAL.
DATA : IT_VBAK TYPE STANDARD TABLE OF T_VBAK,
IT_VBAP TYPE STANDARD TABLE OF T_VBAP,
IT_VBKD TYPE STANDARD TABLE OF T_VBKD,
IT_LIKP TYPE STANDARD TABLE OF T_LIKP,
IT_LIPS TYPE STANDARD TABLE OF T_LIPS,
IT_VBUP TYPE STANDARD TABLE OF T_VBUP,
IT_KNA1 TYPE STANDARD TABLE OF T_KNA1,
IT_ADR6 TYPE STANDARD TABLE OF T_ADR6,
IT_FINAL1 LIKE IT_FINAL OCCURS 0 with header line,
IT_TVLST TYPE STANDARD TABLE OF T_TVLST,
IT_CONFIG TYPE STANDARD TABLE OF T_CONFIG,
W_VBAK TYPE T_VBAK,
W_VBAP TYPE T_VBAP,
W_VBKD TYPE T_VBKD,
W_LIKP TYPE T_LIKP,
W_ADR6 TYPE T_ADR6,
W_LIPS TYPE T_LIPS,
W_VBUP TYPE T_VBUP,
W_KNA1 TYPE T_KNA1,
W_TVLST TYPE T_TVLST,
W_CONFIG TYPE T_CONFIG.
DATA: it_message TYPE STANDARD TABLE OF solisti1 INITIAL SIZE 0
WITH HEADER LINE.
DATA: it_attach TYPE STANDARD TABLE OF solisti1 INITIAL SIZE 0
WITH HEADER LINE.
DATA: t_packing_list LIKE sopcklsti1 OCCURS 0 WITH HEADER LINE,
t_contents LIKE solisti1 OCCURS 0 WITH HEADER LINE,
t_receivers LIKE somlreci1 OCCURS 0 WITH HEADER LINE,
t_attachment LIKE solisti1 OCCURS 0 WITH HEADER LINE,
t_object_header LIKE solisti1 OCCURS 0 WITH HEADER LINE,
w_cnt TYPE i,
w_sent_all(1) TYPE c,
w_doc_data LIKE sodocchgi1,
gd_error TYPE sy-subrc,
gd_reciever TYPE sy-subrc.
SELECTION-CRITERIA *
SELECTION-SCREEN BEGIN OF BLOCK B1 WITH FRAME TITLE TEXT-001.
PARAMETERS : R2 RADIOBUTTON GROUP G1 USER-COMMAND radio DEFAULT 'X',
R1 RADIOBUTTON GROUP G1 .
selection-screen end of block b1.
selection-screen begin of block b2 with frame title text-002.
PARAMETERS: p_email TYPE somlreci1-receiver
DEFAULT '[email protected]'.
PARAMETERS : P_VTWEG LIKE W_VBAK-VTWEG ,
P_WERKS LIKE W_VBAP-WERKS.
select-options : s_vkgrp for w_vbak-vkgrp,
s_ERDAT for w_LIKP-ERDAT.
selection-screen end of block b2.
Initialization
INITIALIZATION.
s_vkgrp-sign = 'I'.
s_vkgrp-option = 'BT'.
s_vkgrp-low = '313'.
s_vkgrp-high = '324'.
APPEND s_vkgrp.
s_erdat-sign = 'I'.
s_erdat-option = 'BT'.
s_erdat-low = '20080108'.
s_erdat-high = '20080108'.
s_erdat-low = '20070101'.
s_erdat-high = sy-datum.
APPEND s_erdat.
selection-screen validations
AT SELECTION-SCREEN.
Validation for Plant.
IF p_werks NE '7210'.
MESSAGE : 'Plant entered should be 7210' TYPE 'E'.
ENDIF.
START OF SELECTION *
start-of-selection.
GETTING THE DATA FROM THE DATABASE TABLE
PERFORM DATA_FETCH.
FILLING THE FINAL INTERNAL TABLE
PERFORM FILL_FINAL.
GETTING THE LIST FOR SENDING MAIL OR DISPLAY.
IF R1 = 'X'.
Populate table with details to be entered into .xls file
LOOP AT IT_CUST.
PERFORM build_xls_data_table using it_cust-kunnr.
ENDLOOP.
Instructs mail send program for SAPCONNECT to send email(rsconn01)
PERFORM initiate_mail_execute_program.
ELSEIF R2 = 'X'.
PERFORM LIST_DISPLAY.
ENDIF.
END OF SELECTION *
end-of-selection.
*& Form DATA_FETCH
text
--> p1 text
<-- p2 text
FORM DATA_FETCH .
SELECT VBELN
VKGRP
KUNNR
ERDAT
VTWEG
LIFSK
VKBUR
INTO TABLE IT_VBAK
FROM VBAK
WHERE VTWEG = P_VTWEG
AND VKGRP IN S_VKGRP
AND LIFSK NE ''.
IF IT_VBAK[] IS NOT INITIAL.
SELECT LIFSP
VTEXT
INTO TABLE IT_TVLST
FROM TVLST
FOR ALL ENTRIES IN IT_VBAK
WHERE LIFSP = IT_VBAK-LIFSK
AND SPRAS = 'EN'.
SELECT VBELN
POSNR
MATNR
WERKS
ARKTX
KWMENG
CUOBJ
NETWR
ZSCHL_K
KONDM
ZZURWN
INTO TABLE IT_VBAP
FROM VBAP
FOR ALL ENTRIES IN IT_VBAK
WHERE VBELN = IT_VBAK-VBELN
AND WERKS = P_WERKS.
SELECT KUNNR
NAME1
ADRNR
INTO TABLE IT_KNA1
FROM KNA1
FOR ALL ENTRIES IN IT_VBAK
WHERE KUNNR = IT_VBAK-KUNNR.
SELECT VBELN
POSNR
BSTKD
BSTDK
KURSK
BZIRK
KDGRP
INTO TABLE IT_VBKD
FROM VBKD
FOR ALL ENTRIES IN IT_VBAK
WHERE VBELN = IT_VBAK-VBELN.
ENDIF.
IF IT_VBAP[] IS NOT INITIAL.
SELECT VBELN
POSNR
VGBEL
VGPOS
INTO TABLE IT_LIPS
FROM LIPS
FOR ALL ENTRIES IN IT_VBAP
WHERE VGBEL = IT_VBAP-VBELN
AND VGPOS = IT_VBAP-POSNR.
ENDIF.
IF IT_LIPS[] IS NOT INITIAL.
SELECT VBELN
ERDAT
INTO TABLE IT_LIKP
FROM LIKP
FOR ALL ENTRIES IN IT_LIPS
WHERE VBELN = IT_LIPS-VBELN
AND ERDAT IN S_ERDAT.
SELECT VBELN
POSNR
KOSTA
WBSTA
INTO TABLE IT_VBUP
FROM VBUP
FOR ALL ENTRIES IN IT_LIPS
WHERE VBELN = IT_LIPS-VBELN
AND POSNR = IT_LIPS-POSNR
AND KOSTA EQ 'C'
AND WBSTA NE 'C'.
ENDIF.
IF IT_KNA1[] IS NOT INITIAL.
SELECT ADDRNUMBER
SMTP_ADDR
INTO TABLE IT_ADR6
FROM ADR6
FOR ALL ENTRIES IN IT_KNA1
WHERE ADDRNUMBER = IT_KNA1-ADRNR.
ENDIF.
ENDFORM. " DATA_FETCH
*& Form LIST_DISPLAY
text
--> p1 text
<-- p2 text
FORM LIST_DISPLAY .
REFRESH F_FIELD.
IF R2 = 'X'.
W_FIELD-col_pos = 1.
W_FIELD-fieldname = 'WERKS'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Plant'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 2.
W_FIELD-fieldname = 'VBELN'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Sales Order'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 3.
W_FIELD-fieldname = 'KUNNR'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Customer Code'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 4.
W_FIELD-fieldname = 'NAME1'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Customer Name'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 5.
W_FIELD-fieldname = 'VBELN1'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Delivery Number'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 6.
W_FIELD-fieldname = 'ERDAT'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Delivery Date'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 7.
W_FIELD-fieldname = 'LIFSK'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Delivery Block'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 8.
W_FIELD-fieldname = 'PUMP_TYPE'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Pump Type'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 9.
W_FIELD-fieldname = 'PUMP_SIZE'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_l = 'Pump Size'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 10.
W_FIELD-fieldname = 'ZZURWN'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Pump Srno'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 11.
W_FIELD-fieldname = 'IHREZ'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Indent No.'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 12.
W_FIELD-fieldname = 'ERDAT'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Order Booking Dt'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 13.
W_FIELD-fieldname = 'NETWR'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C710'.
W_FIELD-seltext_m = 'Net Value'.
w_field-do_sum = 'X'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 14.
W_FIELD-fieldname = 'KWMENG'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C710'.
W_FIELD-seltext_m = 'Qty'.
w_field-do_sum = 'X'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 15.
W_FIELD-fieldname = 'BSTKD'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Customer PONO'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 16.
W_FIELD-fieldname = 'BSTDK'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Customer PODT'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 17.
W_FIELD-fieldname = 'SALORD'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Sales Order/Item'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 18.
W_FIELD-fieldname = 'VTEXT'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Delivery Block Desc.'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 19.
W_FIELD-fieldname = 'FOOTER'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Footer Text'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
W_FIELD-col_pos = 20.
W_FIELD-fieldname = 'ITMTXT'.
W_FIELD-tabname = 'IT_FINAL'.
W_FIELD-emphasize = 'C410'.
W_FIELD-seltext_m = 'Item Text'.
APPEND W_FIELD TO F_FIELD.
CLEAR W_FIELD.
PERFORM SORT_FIELD.
PERFORM LAYOUT_DISPLAY.
PERFORM GRID_DISPLAY.
ENDIF.
ENDFORM. " LIST_DISPLAY
*& Form FILL_FINAL
text
--> p1 text
<-- p2 text
FORM FILL_FINAL .
REFRESH IT_FINAL.
LOOP AT IT_VBUP INTO W_VBUP.
READ TABLE IT_LIPS INTO W_LIPS WITH KEY VBELN = W_VBUP-VBELN POSNR = W_VBUP-POSNR.
READ TABLE IT_LIKP INTO W_LIKP WITH KEY VBELN = W_LIPS-VBELN.
IF SY-SUBRC EQ 0.
READ TABLE IT_VBAP INTO W_VBAP WITH KEY VBELN = W_LIPS-VGBEL POSNR = W_LIPS-VGPOS.
READ TABLE IT_VBAK INTO W_VBAK WITH KEY VBELN = W_VBAP-VBELN.
READ TABLE IT_VBKD INTO W_VBKD WITH KEY VBELN = W_VBAK-VBELN.
READ TABLE IT_KNA1 INTO W_KNA1 WITH KEY KUNNR = W_VBAK-KUNNR.
READ TABLE IT_TVLST INTO W_TVLST WITH KEY LIFSP = W_VBAK-LIFSK.
IT_FINAL-WERKS = W_VBAP-WERKS.
IT_FINAL-VBELN = W_VBAP-VBELN.
IT_FINAL-KUNNR = W_VBAK-KUNNR.
IT_FINAL-NAME1 = W_KNA1-NAME1.
IT_FINAL-VBELN1 = W_LIKP-VBELN.
IT_FINAL-ERDAT = W_LIKP-ERDAT.
IT_FINAL-LIFSK = W_VBAK-LIFSK.
IT_FINAL-ZZURWN = W_VBAP-ZZURWN.
IT_FINAL-IHREZ = W_VBKD-IHREZ.
IT_FINAL-ERDAT1 = W_VBAK-ERDAT.
IT_FINAL-NETWR = W_VBAP-NETWR.
IT_FINAL-BSTKD = W_VBKD-BSTKD.
IT_FINAL-BSTDK = W_VBKD-BSTDK.
IT_FINAL-POSNR = W_VBAP-POSNR.
IT_FINAL-VTEXT = W_TVLST-VTEXT.
IT_FINAL-KWMENG = W_VBAP-KWMENG.
CONCATENATE W_VBAP-VBELN W_VBAP-POSNR INTO IT_FINAL-SALORD SEPARATED BY '/'.
IF W_VBAP-CUOBJ NE '000000000000000000'.
REFRESH IT_CONFIG.
CALL FUNCTION 'VC_I_GET_CONFIGURATION'
EXPORTING
INSTANCE = W_VBAP-CUOBJ
LANGUAGE = SY-LANGU
TABLES
CONFIGURATION = IT_CONFIG
EXCEPTIONS
INSTANCE_NOT_FOUND = 1
INTERNAL_ERROR = 2
NO_CLASS_ALLOCATION = 3
INSTANCE_NOT_VALID = 4
OTHERS = 5.
IF SY-SUBRC = 0.
READ TABLE IT_CONFIG INTO W_CONFIG WITH KEY ATNAM = 'IN_PUMP_TYPE'.
IT_FINAL-PUMP_TYPE = W_CONFIG-ATWRT.
CLEAR W_CONFIG.
READ TABLE IT_CONFIG INTO W_CONFIG WITH KEY ATNAM = 'IN_PUMP_SIZE' .
IT_FINAL-PUMP_SIZE = W_CONFIG-ATWRT.
CLEAR W_CONFIG.
ENDIF.
ENDIF.
move w_vbap-vbeln to name_text.
CALL FUNCTION 'READ_TEXT'
EXPORTING
id = 'ZKT1'
language = 'E'
name = name_text
object = 'VBBK'
TABLES
lines = tline1
EXCEPTIONS
OTHERS = 8.
LOOP AT TLINE1.
CONCATENATE IT_FINAL-FOOTER TLINE1-TDLINE+0(65) INTO IT_FINAL-FOOTER.
CLEAR : TLINE1.
ENDLOOP.
clear : name_text,tline1[].
concatenate w_vbap-vbeln w_vbap-posnr into name_text.
CALL FUNCTION 'READ_TEXT'
EXPORTING
id = 'ZKT3'
language = 'E'
name = name_text
object = 'VBBP'
TABLES
lines = tline1
EXCEPTIONS
OTHERS = 8.
LOOP AT TLINE1.
CONCATENATE IT_FINAL-ITMTXT TLINE1-TDLINE+0(65) INTO IT_FINAL-ITMTXT.
CLEAR : TLINE1.
ENDLOOP.
APPEND IT_FINAL.
ENDIF.
CLEAR : IT_FINAL,W_VBAP,W_VBKD,W_VBUP,W_LIPS,W_LIKP,W_KNA1,W_VBAK,W_TVLST,name_text,tline1[].
ENDLOOP.
IT_FINAL1[] = IT_FINAL[].
SORT IT_FINAL1 BY KUNNR.
LOOP AT IT_FINAL1.
IF TMP NE IT_FINAL1-KUNNR.
IT_CUST-KUNNR = IT_FINAL1-KUNNR.
APPEND IT_CUST.
clear : tmp,it_cust.
TMP = IT_FINAL1-KUNNR.
ENDIF.
CLEAR : IT_FINAL1.
ENDLOOP.
ENDFORM. " FILL_FINAL
*& Form LAYOUT_DISPLAY
text
--> p1 text
<-- p2 text
FORM LAYOUT_DISPLAY .
W_LAYOUT-colwidth_optimize = 'X'.
ENDFORM. " LAYOUT_DISPLAY
*& Form GRID_DISPLAY
text
--> p1 text
<-- p2 text
FORM GRID_DISPLAY .
CALL FUNCTION 'REUSE_ALV_GRID_DISPLAY'
EXPORTING
I_INTERFACE_CHECK = ' '
I_BYPASSING_BUFFER = ' '
I_BUFFER_ACTIVE = ' '
I_CALLBACK_PROGRAM = SY-REPID
I_CALLBACK_PF_STATUS_SET = ' '
I_CALLBACK_USER_COMMAND = ' '
I_CALLBACK_TOP_OF_PAGE = 'TOP_OF_PAGE'
I_CALLBACK_HTML_TOP_OF_PAGE = ' '
I_CALLBACK_HTML_END_OF_LIST = ' '
I_STRUCTURE_NAME =
I_BACKGROUND_ID = ' '
I_GRID_TITLE =
I_GRID_SETTINGS =
IS_LAYOUT = W_LAYOUT
IT_FIELDCAT = F_FIELD
IT_EXCLUDING =
IT_SPECIAL_GROUPS =
IT_SORT = T_SORT
IT_FILTER =
IS_SEL_HIDE =
I_DEFAULT = 'X'
I_SAVE = ' '
IS_VARIANT =
IT_EVENTS =
IT_EVENT_EXIT =
IS_PRINT =
IS_REPREP_ID =
I_SCREEN_START_COLUMN = 0
I_SCREEN_START_LINE = 0
I_SCREEN_END_COLUMN = 0
I_SCREEN_END_LINE = 0
IT_ALV_GRAPHICS =
IT_HYPERLINK =
IT_ADD_FIELDCAT =
IT_EXCEPT_QINFO =
I_HTML_HEIGHT_TOP =
I_HTML_HEIGHT_END =
IMPORTING
E_EXIT_CAUSED_BY_CALLER =
ES_EXIT_CAUSED_BY_USER =
TABLES
T_OUTTAB = IT_FINAL
EXCEPTIONS
PROGRAM_ERROR = 1
OTHERS = 2
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
ENDFORM. " GRID_DISPLAY
*& Form SORT_FIELD
text
--> p1 text
<-- p2 text
FORM SORT_FIELD .
w_sort-spos = 1.
w_sort-fieldname = 'KUNNR'.
w_sort-up = 'X'.
append w_sort to t_sort.
clear w_sort.
w_sort-spos = 2.
w_sort-fieldname = 'VBELN'.
w_sort-up = 'X'.
append w_sort to t_sort.
clear w_sort.
ENDFORM. " SORT_FIELD
*& Form TOP_OF_PAGE
text
FORM top_of_page.
IF R2 = 'X'.
REFRESH l_header.
w_header-typ = 'S'.
w_header-key = 'Delivery Block : '.
w_header-info = 'Outbound delivery created but not despatched'.
APPEND w_header TO l_header.
CLEAR w_header.
CALL FUNCTION 'REUSE_ALV_COMMENTARY_WRITE'
EXPORTING
it_list_commentary = l_header.
ENDIF.
ENDFORM. "TOP_OF_PAGE
*& Form BUILD_XLS_DATA_TABLE
Build data table for .xls document
FORM build_xls_data_table using custcode.
CONSTANTS: con_cret TYPE X VALUE '0D', "OK for non Unicode
con_tab TYPE x VALUE '09'. "OK for non Unicode
data : it_custcode like vbak-kunnr.
*If you have Unicode check active in program attributes thnen you will
*need to declare constants as follows
*class cl_abap_char_utilities definition load.
constants:
con_tab type c value cl_abap_char_utilities=>HORIZONTAL_TAB,
con_cret type c value cl_abap_char_utilities=>CR_LF.
clear : it_attach,it_attach[].
CONCATENATE 'Customer PONO' 'Customer PODT' 'Sales Order No' 'Item No'
'Pump Type' 'Pump Size' 'Order Value Rs' 'Delivery No.' 'Delivery Dt.'
'Quantity' 'Reasons for not getting Despatch'
INTO it_attach SEPARATED BY con_tab.
CONCATENATE con_cret it_attach INTO it_attach.
APPEND it_attach.
it_custcode = custcode.
CLEAR : W_KNA1,W_ADR6. "Code need to be added once testing is over.
READ TABLE IT_KNA1 INTO W_KNA1 WITH KEY KUNNR = IT_CUSTCODE.
READ TABLE IT_ADR6 INTO W_ADR6 WITH KEY ADDRNUMBER = W_KNA1-ADRNR.
P_EMAIL = W_ADR6-SMTP_ADDR.
LOOP AT it_final where kunnr = it_custcode.
CONCATENATE
IT_FINAL-BSTKD
IT_FINAL-BSTDK
IT_FINAL-VBELN
IT_FINAL-POSNR
IT_FINAL-PUMP_TYPE
IT_FINAL-PUMP_SIZE
IT_FINAL-NETWR
IT_FINAL-VBELN1
IT_FINAL-ERDAT
IT_FINAL-KWMENG
IT_FINAL-VTEXT
INTO it_attach SEPARATED BY con_tab.
CONCATENATE con_cret it_attach INTO it_attach.
APPEND it_attach.
clear it_final.
ENDLOOP.
if R1 = 'X'.
Populate message body text
perform populate_email_message_body.
Send file by email as .xls speadsheet
PERFORM send_file_as_email_attachment
tables it_message
it_attach
using p_email
'AWAITING DESPATCH CLEARANCE'
'XLS'
'Delivery_Block'
'Delivery_Blk'
'[email protected]'
'INT'
changing gd_error
gd_reciever.
endif.
ENDFORM. " BUILD_XLS_DATA_TABLE
*& Form SEND_FILE_AS_EMAIL_ATTACHMENT
Send email
FORM send_file_as_email_attachment tables pit_message
pit_attach
using p_email
p_mtitle
p_format
p_filename
p_attdescription
p_sender_address
p_sender_addres_type
changing p_error
p_reciever.
DATA: objhead LIKE solisti1 OCCURS 1 WITH HEADER LINE.
DATA: ld_error TYPE sy-subrc,
ld_reciever TYPE sy-subrc,
ld_mtitle LIKE sodocchgi1-obj_descr,
ld_email LIKE somlreci1-receiver,
ld_format TYPE so_obj_tp ,
ld_attdescription TYPE so_obj_nam ,
ld_attfilename TYPE so_obj_des ,
ld_sender_address LIKE soextreci1-receiver,
ld_sender_address_type LIKE soextreci1-adr_typ,
ld_receiver LIKE sy-subrc.
ld_email = p_email.
ld_mtitle = p_mtitle.
ld_format = p_format.
ld_attdescription = p_attdescription.
ld_attfilename = p_filename.
ld_sender_address = p_sender_address.
ld_sender_address_type = p_sender_addres_type.
Fill the document data.
w_doc_data-doc_size = 1.
Populate the subject/generic message attributes
w_doc_data-obj_langu = sy-langu.
w_doc_data-obj_name = 'SAPRPT'.
w_doc_data-obj_descr = ld_mtitle .
w_doc_data-sensitivty = 'F'.
Fill the document data and get size of attachment
CLEAR : w_doc_data,w_cnt.
DESCRIBE TABLE it_attach LINES w_cnt.
READ TABLE it_attach INDEX w_cnt.
w_doc_data-doc_size =
( w_cnt - 1 ) * 255 + STRLEN( it_attach ).
w_doc_data-obj_langu = sy-langu.
w_doc_data-obj_name = 'SAPRPT'.
w_doc_data-obj_descr = ld_mtitle.
w_doc_data-sensitivty = 'F'.
CLEAR t_attachment.
REFRESH t_attachment.
t_attachment[] = pit_attach[].
Describe the body of the message
CLEAR t_packing_list.
REFRESH t_packing_list.
t_packing_list-transf_bin = space.
t_packing_list-head_start = 1.
t_packing_list-head_num = 0.
t_packing_list-body_start = 1.
DESCRIBE TABLE it_message LINES t_packing_list-body_num.
t_packing_list-doc_type = 'RAW'.
APPEND t_packing_list.
Create attachment notification
t_packing_list-transf_bin = 'X'.
t_packing_list-head_start = 1.
t_packing_list-head_num = 1.
t_packing_list-body_start = 1.
DESCRIBE TABLE t_attachment LINES t_packing_list-body_num.
t_packing_list-doc_type = ld_format.
t_packing_list-obj_descr = ld_attdescription.
t_packing_list-obj_name = ld_attfilename.
t_packing_list-doc_size = t_packing_list-body_num * 255.
APPEND t_packing_list.
Add the recipients email address
CLEAR t_receivers.
REFRESH t_receivers.
t_receivers-receiver = ld_email.
t_receivers-rec_type = 'U'.
t_receivers-com_type = 'INT'.
t_receivers-notif_del = 'X'.
t_receivers-notif_ndel = 'X'.
APPEND t_receivers.
CALL FUNCTION 'SO_DOCUMENT_SEND_API1'
EXPORTING
document_data = w_doc_data
put_in_outbox = 'X'
sender_address = ld_sender_address
sender_address_type = ld_sender_address_type
commit_work = 'X'
IMPORTING
sent_to_all = w_sent_all
TABLES
packing_list = t_packing_list
object_header = objhead
contents_bin = t_attachment
contents_txt = it_message
receivers = t_receivers
EXCEPTIONS
too_many_receivers = 1
document_not_sent = 2
document_type_not_exist = 3
operation_no_authorization = 4
parameter_error = 5
x_error = 6
enqueue_error = 7
OTHERS = 8.
Populate zerror return code
ld_error = sy-subrc.
Populate zreceiver return code
LOOP AT t_receivers.
ld_receiver = t_receivers-retrn_code.
ENDLOOP.
ENDFORM.
*& Form INITIATE_MAIL_EXECUTE_PROGRAM
Instructs mail send program for SAPCONNECT to send email.
FORM initiate_mail_execute_program.
WAIT UP TO 2 SECONDS.
SUBMIT rsconn01 WITH mode = 'INT'
WITH output = 'X'
AND RETURN.
ENDFORM. " INITIATE_MAIL_EXECUTE_PROGRAM
*& Form POPULATE_EMAIL_MESSAGE_BODY
Populate message body text
form populate_email_message_body.
REFRESH it_message.
it_message = 'We have manufactured the pump/s against your purchase order and regret to inform'.
APPEND it_message.
it_message = 'you that same cannot be despatched for the reason/s indicated below.'.
APPEND it_message.
it_message = ' '.
APPEND it_message.
it_message = 'Please find the below attachment "Delivery_Blk.xls" for the details.'.
APPEND it_message.
it_message = ' '.
APPEND it_message.
it_message = 'We now request you to send the required detail/s by return mail/post to enable us '.
APPEND it_message.
it_message = 'to despatch the pump/s at the earliest.'.
APPEND it_message.
it_message = ' '.
APPEND it_message.
it_message = ' '.
APPEND it_message.
it_message = 'Best Regards'.
APPEND it_message.
it_message = 'O.E. ENGINEER'.
APPEND it_message.
endform. " POPULATE_EMAIL_MESSAGE_BODYHi,
Refer to the following piece of code. This is the simple code to send email with content and attachment.
Declaration
DATA: lwa_hd_change TYPE sood1,
lt_objcont TYPE STANDARD TABLE OF soli,
lwa_objcont TYPE soli,
lt_receivers TYPE STANDARD TABLE OF soos1,
lwa_receivers TYPE soos1 ,
lt_att_cont TYPE STANDARD TABLE OF soli,
lwa_att_cont TYPE soli,
lt_packing TYPE STANDARD TABLE OF soxpl,
lwa_packing TYPE soxpl,
lf_sent TYPE sonv-flag,
lf_size TYPE i.
CONSTANTS: lc_obj(11) TYPE c VALUE 'BOMSouthco',
lc_desc(20) TYPE c VALUE 'BOM Download',
lc_lang(1) TYPE c VALUE 'E',
lc_raw(3) TYPE c VALUE 'RAW',
lc_net(1) TYPE c VALUE 'U',
lc_mail(4) TYPE c VALUE 'MAIL',
lc_xls(3) TYPE c VALUE 'XLS',
lc_ext(3) TYPE c VALUE 'EXT'.
Passing values to the strutures used in SO_OBJECT_SEND function module
lwa_hd_change-objla = lc_lang.
lwa_hd_change-objnam = lc_obj.
lwa_hd_change-objdes = lc_desc.
lwa_hd_change-objlen = 255.
lwa_objcont-line = text-t29.
APPEND lwa_objcont TO lt_objcont.
CLEAR lwa_objcont.
lwa_receivers-recextnam = text-t31.
lwa_receivers-recesc = lc_net.
lwa_receivers-sndart = lc_mail.
lwa_receivers-sndex = 'X'.
lwa_receivers-sndpri = 1.
lwa_receivers-mailstatus = 'E'.
APPEND lwa_receivers TO lt_receivers.
CLEAR lwa_receivers.
lwa_receivers-recextnam = text-t30.
lwa_receivers-recesc = lc_net.
lwa_receivers-sndart = lc_mail.
lwa_receivers-sndex = 'X'.
lwa_receivers-sndpri = 1.
lwa_receivers-mailstatus = 'E'.
APPEND lwa_receivers TO lt_receivers.
CLEAR lwa_receivers.
Passing values for the attachment file
LOOP AT gt_output INTO gwa_output.
CONCATENATE gf_lf gwa_output-matnr gf_etb gwa_output-idnrk gf_etb
gwa_output-type gf_etb gwa_output-menge gf_etb
gwa_output-meins gf_etb gwa_output-comp gf_etb
INTO lwa_att_cont-line.
APPEND lwa_att_cont TO lt_att_cont.
CLEAR lwa_att_cont.
ENDLOOP.
CHECK lt_att_cont IS NOT INITIAL.
DESCRIBE TABLE lt_att_cont LINES lf_size.
lwa_packing-transf_bin = ' '.
lwa_packing-head_start = 1.
lwa_packing-head_num = 0.
lwa_packing-body_start = 1.
lwa_packing-body_num = lf_size.
lwa_packing-file_ext = lc_xls.
lwa_packing-objlen = lf_size * 255.
lwa_packing-objtp = lc_ext.
lwa_packing-objdes = lc_desc.
lwa_packing-objnam = lc_obj.
APPEND lwa_packing TO lt_packing.
CLEAR lwa_packing.
CHECK gf_error IS NOT INITIAL. "Check if unix file is written
FM to send email to the intended recipients
CALL FUNCTION 'SO_OBJECT_SEND'
EXPORTING
object_hd_change = lwa_hd_change
object_type = lc_raw
IMPORTING
sent_to_all = lf_sent
TABLES
objcont = lt_objcont
receivers = lt_receivers
packing_list = lt_packing
att_cont = lt_att_cont
EXCEPTIONS
active_user_not_exist = 1
communication_failure = 2
component_not_available = 3
folder_not_exist = 4
folder_no_authorization = 5
forwarder_not_exist = 6
note_not_exist = 7
object_not_exist = 8
object_not_sent = 9
object_no_authorization = 10
object_type_not_exist = 11
operation_no_authorization = 12
owner_not_exist = 13
parameter_error = 14
substitute_not_active = 15
substitute_not_defined = 16
system_failure = 17
too_much_receivers = 18
user_not_exist = 19
originator_not_exist = 20
x_error = 21
OTHERS = 22.
IF sy-subrc = 0.
MESSAGE s004 WITH text-t34.
ENDIF.
COMMIT WORK.
Reward if helpful.
Regards,
Ramya -
I have a PCI-FBUS card (dual port), can't connect over 60 devices to it?
I connect to various Fieldbus devices (all from the same manufacturer and same type as we are an OEM) that I am testing (I have 80 in my test system). I have the dual port PCI Fieldbus card and am running communication manager 3.2 on Windows XP with service pack 2. As part of my pretest (getting the devices on the bus and assigning them a unique address) I connect to a device and change its address to 20 and power off the device to have it drop off the bus then relay in the next device and connect to it and change the address to 21 etc etc---this process makes it easiest for me as then all I have to do is connect to the only device on the bus and know that it is the device I am interested in assigning to it a new unique address as the others are not on the bus. I am able to get 30 devices per port (60 devices total since I have a dual port card). After the 30th device is connected, albeit no devices show up on the bus since they are all powered off, I relay in my 31st device but I can't connect to it on a given port (at this point I have 30 devices that were connected to each port but are now powered off). I have the card configured to operate within the address range of 16-102 for both ports.
What is the limit of the number of devices that can be connected to a given port? What would be the recommended way of connected say 80 devices to a PCI card (40 per port). For my application, after the so called pretest is complete, I do have to have up to 8 devices powered on at the same time (4 per port) so that is why I want to keep the addresses unique per device. By the way I know this is not a physical connection issue with my station as I can connect to all devices when I limit my test to 60 devices (i.e. I can do the first 60 or the last 60 so the wiring etc is good as well as my assigned address space/parameters for the NI card).
Some of My NI card parameters are,
Dlme Link Master Info,
Dlme Scheduling Overhead 4
Def Min Token Deleg Time 84
Def Token Hold Time 700
Target Token Rot Time 4096
Link Maint Tok Hold Time 0x0
Time Distribution Period 5000
Max Inactivity to claim Las Delav 100
Las DB Spdu Distri Period 200
System Management Info,
Primary Time Master 0x10
T1 0x75300
T2 0x2bf200
T3 0x15f900
Clock Sync Interval 10
Dlme Basic Info,
slot time 8
Slpdu Phl Overhead 0
Max Response Delay 10
First Unpolled Node 0x66
Number of Unpolled Node 0x79
This link 0
Min Inter-Pdu Delay 16
Preamble Extension 0
Post Trans Gap Extension 0
Max Inter Chan Signal Skew 0
Time Sync Class 1ms
Thanks
JimHello Jim,
In NI-FBUS, the max number of devices that can be connected to a segment (port) at one same time is 32. This value is defined by FF specification.
Please try the following method.
After connecting the 30th device, restart NI-FBUS Communications Manager (CM), then connect the 31th device. Check whether the problem still occurs.
Regards
Feilian (Vince) Shen -
Cisco 2432-24FXS Calls won't ring FXS ports when placed in Huntgroup
Hi,
I am having an issue getting calls to ring through on the FXS ports when using the "trunkgroup" command under the POTS dial-peers. Calls will ring through fine if I use the "port" command under the pots dial-peer. What I am trying to accomplish is getting a single number to hunt through 13 FXS ports in a round-robin fashion. With the below setup I am getting a SIP 404 not found message in the SIP debug info. I am not sure if I am missing something here or what the deal is. If the below information is not enough I would be happy to provide additional info. Any idea's why this configuration doesn't seam to work?
trunk group HuntGroup1
hunt-scheme round-robin both up
dial-peer voice 1 voip
translation-profile outgoing 7to11
destination-pattern .T
progress_ind setup enable 3
no modem passthrough
voice-class codec 1
session protocol sipv2
session target dns:XXXXXXXX
dtmf-relay rtp-nte
fax rate 14400
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
ip qos dscp cs5 media
no vad
dial-peer voice 300 pots
trunkgroup HuntGroup1
description TEST NUMBER
destination-pattern XXXXXXXXXX
voice-port 2/0
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 1
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/1
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 2
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/2
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 3
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/3
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 4
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/4
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 5
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/5
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 6
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/6
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 7
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/7
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 8
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/8
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 9
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/9
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 10
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/10
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 11
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/11
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 12
station-id number XXXXXXXXXX
caller-id enable
voice-port 2/12
trunk-group HuntGroup1
timeouts interdigit 3
description HuntGroup 1 Line 13
station-id number XXXXXXXXXX
caller-id enable
Message was edited by: Thomas Schmidt
Added CCSIP Debug and Router Config.Hi.
Can you please attach the complete config and a debug ccsip message?
Thanks
Regards
Carlo
Sent from Cisco Technical Support iPhone App -
Advice about FXS Port configuration for connecting to modems
Hello all,
We have not confirm the problem, but we are having reports that analog devices like USR V.92 Modems and Power meters are not connecting or dropping the connection. We have an ISR 2911 with the 4-port FXS-DID WIC (VIC3-4FXS/DID), configure to an internet SIP truck provider. The Router is running IOS 15.3(3)M2. If we connect an analog phone to the FXS port and call, voice is clear. So the question is what configuration settings should we have for FXS ports and/or dialpeers for connections to modems? Attached is the current configuration of the router.
Do we have to be worried about Codec? If so which Codec should we configure?
Any Physical FXS settings should be set?
Are my DSP setup correctly?
Again, I'm at a loss, as voice sounds good and my searches for modem connections to FXS Ports on CUCME is coming up dry. Any help would be great.
As far as the "Power Meters", we are talking substation power meters.
Thanks for any advice you can spare and your time,
NickHi Amit,
No problem on the delay. Your help is very much appreciated.
You're losing me a bit. Because I don't know if your giving me dial-peer 1 as an example. 1 being just a random number. Or your telling me to change my current dial-peer 1 configuration. Which is currently a pots dial-peer:
dial-peer voice 1 pots
description POTS port 0/1/0
destination-pattern 111111111
port 0/1/0
dial-peer 1000 voip is our outbound call leg. Sorry call legs are not exactly clear to me yet. In fact they haven't been in years. :) So change my dial-peer to dial-peer voice 1 voip?
My other question still unknown to me is should we use:
fax protocol pass-through g711ulaw
Even though we are trying to use a modem and not a fax? Also this command is a dial-peer command and not a global command. So what global command should i be using?
Again thank you for your time and help,
Nick -
I have a Cisco 1760 with FXS ports in it that connect to a PBX. Everything works fine, but i cannot seem to pass DTMF tones to the PBX.
If a caller calls in and gets the auto attendant, they need to dial 100 for one user, 200 for another and so on.
Can this work with FXS ports?
DaveWe are using h323 and our dial-peer looks like this:
dial-peer voice 6101 voip
huntstop
destination-pattern 6045551234
session target ipv4:10.157.0.2
dtmf-relay rtp-nte
fax rate 7200
ip qos dscp cs5 media
no vad
We tried the dtmf-relay h245-alphanumeric and still have the same issue.
When i use dtmf-relay rtp-nte it works from my cell phone (Bell Canada) but not from Rogers or Telus. Any ideas? -
I am using Call-manager 6.0.1b, a MGCP controlled Gateway.On the Gateway i have installed a NM-HD-2V with a Vic2-2FXS module. On this module i connect 2 analog phone with capability to display the Caller-ID. When i call the analog port from a ip phone or from the other analog phone the Dn is not shown. When i connect the phone directly to the PSTN and dial this nr via my cell phone the nr is shown so i expect that the nr format received is not correct. How can this performed that the correct format is shown to the FXS port connected phone ?
Hi,
Yes - you are correct. Looked at this one too quickly.
You will want to make sure the CPTONE defined on the port is for the country the phone is manufactured for, and that the voice-pport has the 'caller-id enable' command.
If those are both correct, and I'm guessing that they are since some caller-id works, then you need to inspect the gateways that take the calls to begin with.
Do you have caller-id trouble for internal calls also?
How do these calls come into your network?
hth,
nick -
Agent port passed by user Is busy
I'm helping with their OEM 12c evaluation and we cannot get past this issue :-
Issue similar to below note:
EM 12c: Agent Deployment Fails With Error: "Agent port passed by
user is busy and cannot proceed with the configuration" (Doc ID 1473185.1), but it is not
a) There no duplicate entries in /etc/hosts file of agent machine for
agent hostname.
b) etc/hosts file OMS and Agents are fine.
c) Agent and OMS ,IPaddress,Short hostname and complete hostname are
able to resolve.
d) Included OMS host details in Agent etc/hosts file, but still same issue
e) checked the if the 1830 port is open or not: Its fine
netstat -tulpn | grep :1830
To me this error seems to be a catch all anybody any other ideasHi Phill,
Following up with you over an email
-Akanksha -
hi!
How can I forward the Calls on an Phone witch is connected to an FXS-Port (mgcp, vg200)?
How can I use the other Features, like PickUp etc.
vy MarkusSince there has been no response to your post, it appears to be either too complex or too rare an issue for other forum members to assist you. If you don't get a suitable response to your post, you may wish to review our resources at the online Technical Assistance Center (http://www.cisco.com/tac) or speak with a TAC engineer. You can open a TAC case online at http://www.cisco.com/tac/caseopen
If anyone else in the forum has some advice, please reply to this thread.
Thank you for posting. -
Is there a way to make an analog phone connected to an FXS port a part of a call pickup group that contains both analog phones & IP phones? I setup a lab and used MGCP to add the gateway and I was able to add the DN associated with the FXS port to a call pickup group. However, I am unable to figure out how to answer the call from the analog phone when another IP phone in the call pickup group is ringing.
Thanks in advanceHi
You are going down the right track with this.
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Unified%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1dde5372/0#selected_message
See this other post I made (for a different purpose, but the principal is the same - it just opens up features available to IP phones for FXS ports by registering them using SCCP).
Regards
Aaron
Please rate helpful posts...
Maybe you are looking for
-
I am trying to use VPD in our application. It works fine if I directly use SQL select statement. However I can not get the right reocrd set if the SQL statement in stored procedures, functions, or package. Your kind reply will be highly appreciated.
-
I can't save and open .ai files.
Hello. I can't save and open the file with special character in virtual drive(using communications). -> refer to this.. ( http://software.naver.com/software/summary.nhn?softwareId=MFS_105031 ) *Special character I used is 黒(not 黑). If I rename the fi
-
Metadata ON image in browser view?
i have been finding an issue in deleting duplicate images which i am doing manually and i am wondering if anyone can help with this. since these duplicates are the same /image/ but may not have the same name or the same resolution i do the following
-
Logging Standards and ADF Application Log File on Standalone WLS
Hi Experts, I am using JDev - 11.1.1.5.0 and WLS - 10.3 Is ADF Logger the standard logger to be used in an ADF Application? If Yes, how to configure it? During development I simply used "System.out.println" for log messages and I was able to see the
-
Hi folks, I am new to the area of ALE-IDOC's . could you please provide the document for that if possible. I want the manual steps for that with transaction codes. Could you please provide the documentation alone for the IDOCS. Thanks & Regards, Sur