Work Center Integration PM-PP

I have 3 similar Production Machines. I will load any or all of them according to the requirement or acc. to which machine is free.
so PP person says, he has to assign only one Work Center to all the three machines as he can not assign more than one Work center for a single Operation in Routing.
But in PM, 3 machines will have 3 different Equipment numbers with common Production Work Center (Work Center at Location tab page)
If I block any one of the machines for Maintenance, that work Center will get blocked. But physically remaining two machines are free. But PP person can not dispatch the Order as work center is blocked.
Plz guide how to proceed

hi,
SAM,
For 3 production machines PP Persone should create 3 pp workcenters......,
as far as my knowledge is concern in standard SAP this is not possible.....
although Capacity spiliting option is available in PP workcenter.
but that dosn't solve our proble..
if u set system condition - not in operation for a equipment
.. this will capture whole PP work center..... rather than perticular equipment.
Try to conyence them for 3 pp workcenter.
regards,
Amit kushwaha

Similar Messages

PP work center integration with PM equipment

Hello PM Guru's,
I have a requirement for my client who is producing glass bottles.
The single line producing glass, consist of some 10 stages of processing. The entire line is an integrated one. Like this line equipment they are having around 30 line apprx. During PP implementation, they had considered that line as only one work center/per line and established hourly entry of production confirmation.
Now, during PM implementation, they wanted to consider that line as one equipment, and its sections as either as assembly/sub-equipment.
Currently, if one section fails, the remaining sections runs, and the breakdown are considered as 1/10th.
They are prepared to create dummy PP work center for their sections individually.
Also, they don't want to attach that single PP work center to that entire equipment and its assembly/sub-equipment, because they don't want to have the impact of breakdown stoppage of single section into the whole line. (Due to discrete manufacturing set-up)
They also want to have OEE established, section-wise. Please let me know, for this scenario, how to map that line equipement, and integarte with the PP work center.
Thank you with regards,
Sekar

Hi
If you want to interface between PP &PM. then only you have to think of disturbing already inplmented PP.
Interface between PP& PP means , when PM order is created due to schedule breakdown on a particlur equipment, it should be unaavailble for planning for production.
In your update , you have not mentioned clearly this point.
Is it rquired or not.
Pl. update.
Regards
YMREDDY

PP-PM Integration (Work Center)

Hi all,
In my client place, they have 10 similar Production machines with equal capacities and perform same function.
So, as per the availability of any of those machines, production people will load the machine against Production Order. To do this, they have created only ONE workcenter with 10 Individual Capacities.
So, they have assigned that Work Center in the Routing and as per the availability of 10 individual Capacities, they can confirm and dispatch the P.O.
If we consider PM, 10 different Equipment nos have to be generated with the same work center. So if I block any of those 10 Equipments, that work center will get blocked and they can not dispatch the PO.
Please guide and give your inputs to how to proceed in this scenario.
Thnx in advance
Sam

hi,
u r correct. I am also looking for a rectification only.
In case of Process industry, this std scenario will work , as if any one of the machine gets stopped, all other machine can not run.
to put in a simple way, if output of one machine is the input of next machine, then we can accomodate ONE workcenter for all the machines in that chain/assembly/line.
in my case the requirement is, none of the machines' output is linked with others input.
If anybody could find any user exits/Badi or any other solution, please give ur valuable points.
Sam

Work Center Block

Hi Experts,
We have one scenario
W/C in PP(wc category m/c) = Equipment in Plant maintenance
Is it possible to block the W/C automatically whenever there is creation of maintenance order for equipment(w/c for PP) so that it is blocked in routing and can not be used in production.
Thanks in advance,
Amit Kataria

Dear,
You can lock work center. if work center is lock, now production order will be created with locked work center.
If you require that whenever maintenance order created against specific equipment in which locked work center used, system will not allow to create production or production order execution. In SAP Maintenance, there is integration with PP that whenever maintenance order created, system will not allow to execute production order. Kindly consult with you PM consultant in this regard.
Thanks
Muhammad Ashfaq

Block production work center during maintenance order

Dear Experts,
iam trying to do the integration between PM and PP, I want to block the production work center from any production order when there is any maintenance order opened for a certain equipment which is inside this work center ,
till now i did the following:
1) the production work center is now inside the equipment location tab
2) when i open any maintenance order i put system condition as zero
now what i only achieved ,
- in transaction CM25 the capacity is black for the period of the maintenance order
BUT the work center is not blocked and any production order can be created without any error
please help and much thanks in advance
Best Regards

Hi,
Till time you have performed right things to integrate PP-PM & system is also responding according to setting.
Showing block capicity in CM25 against the Maintenance Order.
If you want to block production order as well, you need to do one more setting.
go to t- code OIOI, selection Production order types (those you want to block) & in capacity Availabilty choose Collect conversion as 3 : No creation if there is insufficiant caacity.
i hope this will definately solve your problem.
- Yatharth

Automatic creation of work center per new employee

Dear gurus,
Is it possible to instantly create Work Centers every time an employee is hired and created via HR module? We consider an employee as "created" when infotypes 0000-0002 are accomplished.
Work centers in PS are manually done in CNR1.
The reason for this integration is that the Work Center needs data from HR's personnel master data such as: name and cost center. And it will be tedious to manually create work centers every time a new employee is hired.
We are thinking this will be done via an ABAP batch input program which just automates the two transactions (PA40 and CNR1). However is there a simpler way to do this? For example, a SAP standard method that we're not seeing?
Thank you!
Regards,
Mozart

HI,
I think it can be handled in the following manner
Use Dynamic Action to call a Cutsom Routine which will inturn do all the actions required. Take Abaper help ..

Work center in solution manager

Hi,
In the work center of solution manager, while trying to create job documentation : [https://websmp107.sap-ag.de/~sapidb/011000358700001975992008E/index.htm] from a change request the final step is to assign a logical component. When I click on the logical component icon my logical component list doesn't show up even though its maintained in the system. Is there some configuration involved?
Thanks,
Esha

Hello Esha,
if I understood your issue correctly your creating the Job Documentation from the Job Change Document (transaction type SDCD) -> you are using the ChaRM integration, right?
In that case you'll have to check IBase assigned to the Job and Change Request: The IBase has to point to a production system.
The program also filters for logical components having the (logical) System, i.e. combination of System ID and Client, of the assigned IBase, assigned in the role production.
-> So you need a logical component which includes the selected system (see IBase) in role production.
Regards,
Martin
Please follow us on SDN:
http://www.sdn.sap.com/irj/scn/weblogs?blog=/pub/u/25168834 [original link is broken] [original link is broken]
/people/martin.lauer/blog
and SAP Service Marketplace:
http://service.sap.com/jsm

Payment Terms in account work center

HI All,
where can I found the Payment Terms into the Account Work Center?
Is it possible to add this information into the Account overview?
Thank for any help.
Simone

Hi Simone,
You can find it in the Sales Data Tab.
This data comes from ECC (if you have an integrated scenario) and is not editable in C4C.
Kind regards,
Henri

Parallel processing in the same work center

Dear Guys,
There is a routing sequence in which some 2-3 operations will occur parallely & those operations will belong to a same work center,How to map those operations in the routing,do i need to maintain parallel processing ,if so then how to go about

Parallel Sequence
Definition
A linear sequence of operations that is parallel to a sequence of operations in the standard sequence.
Use
A parallel sequence enables you to process several operations at the same time. A parallel sequence is carried out at the same time as the corresponding section in the standard sequence. It is a special form of overlapping operations.
Integration
You can create parallel sequences in routings and rate routings. You cannot create them in reference operation sets or reference rate routings.             Creating a Parallel Sequence
Call up the sequence overview.
Choose Edit ® New entries.
The Choose Sequence Category dialog box appears.
Select Parallel sequence and press Continue.
The Sequence Details screen is displayed.
Enter the necessary data.
Select Operation overview to create operations for the parallel sequence.
so particularly in your case
WORK CENTRE OF 10, 20, 30 ,40, 50 ASSUME TO THERE
OPERATION OF THE SEQU : 1,2,3,4,5
SUPPOSE 3,4 ARE PARALLEL SEQUN AND THE WORK CENTRE 30,40 ARE SAME TYPRE TO OPR SAME
YOU MAY DESIGN AS
                                                       WC-30
                                                        (OPN3)
                 W.C 10          WC 20                                WC50
                  (OPN1)          (OPN2)                               (OPN5)
                                                       WC 40
                                                       (OPN4)
OR
                                                       WC-30
                                                        (OPN4)
                 W.C 10          WC 20                                WC50
                  (OPN1)          (OPN2)                               (OPN5)
                                                       WC 40
                                                       (OPN3)

PM-HR assigning work center to employee changes position

Dear all,
   I have an urgent issue, and I have absolutelly no idea how to resolve it, because it takes place in the module PM, and I dont know anything about it.
   The problem is that when users go to tcode IR02 and make an asignament of a employee to a work center the system also changes the position of the employee for the work center (I mean, SAP in the back ground goes to Infotype 0001 of the employee and changes the position of the employee).
   Is there a way of avoiding it? I think it is due to a bad customizing in the integration PM-HR, but Im not sure at all.
PS: sorry if this is the wrong forum to post it, I didnt find a PM forum, If you know a forum that fixes better please let me know!!!
Any advice will be GREATLY appreciated and rewarded
Thanks a lot in advance

Hello Wayne,
I am not sure how you 'assign' an SFC to an operator (User). Anyway, you may use Certification functionality of ME to 'certify' some particular Users on Operations/Resources etc. KBA #1618564 may be helpful for you.
Regards,
Alex.

PP Work Center.

What is significance of assigning PP Work center in the equipment and functional location master data ?
Is their any report or analysis based on this ?
Regards,
VM

Hi Vijay,
The main integration between PM & PP is Workcenter. The production workcenter is created as Equipment in the PM module .
The equipment master accomodates two work centers. The Main (maintenance) workcenter and the production workcenter.
The maintenance workcenter is maintained in the location tab, location data screen area. The production center is maintained in the organization tab, Responsibilities screen area..
Eg for Maintenance Workcenter : Fitter , Electrician
Eg for Production Workcenter : Lathe , Conveyor
If there is a maintenance to be performed on the equipment it means that the production workcenter's capacity is not available.
Regards,
Santhosh

PP work center capacity and link in Equipment master

Dear All
My client has five equipments which he is clubing them into one work center with five capacities. In equipment master i have given for respective equipments i have given PP work center locations but when i create a maint order for one equip then in planning the capacity avalability is affecting the entire work center for ex if the total work on one equip is 12 hrs then only 8 hrs of capcity should be deducted for to day and 4 hrs for tommorow but in plannig all 12 hrs are getting deducted in todays capacity itself.
Pls give some inputs from your experiances
Thanks and Regards
Pankaj

Hi,
Even if we have more than One Equipments in the same work center, PP-PM integration will work.
This is the standard scenario in any Process Industry or in case of an Assembly line of a Automobile manufacturing industry.
So it should work. Please check the following points again,
1. Assignment of Work Center to Equipment Master
2. System Condition - '0' Not in Operation in Both header as well as against Individual Operations (in Work Order for that Equipment)
3. Work Order has been released.
4. Same Work Center is used in Routing and the same is Planned for a period.
If we have all the above points right, then while dispatching the Production Order system should show the Period of block and should shift/plan the PO accordingly.
Regards
Sam

Blocking of Production Work Center

Hi All,
I have already maintained the following PM-PP integration points:
1) Production work center is maintained in equipment master
2) System condition is entered in maintenance order as "Not in operation"
Please let me know how to block the production workcenter for production work when same workcenter (as equipment in PM)is planned for maintenance.
Sundar

Hi,
Once you have done the settings, if you have Maintenance Order on particular eqpt belonging to PP Work Center ,
Then based on system condition the PP Work Capacity will be 0 i believe ..but system will still allow you to create a PP Order on that PP work center .. better thing is to perform Capacity Availablity Check while releasing the PP Order at that PP Work Center and if capacity is not avaialble then u can stop release of the PP Order..
In PP ->OPJK for combination of PP Work order type and plant u have for business function 02 , u have give Overall Profile
Release Capacities as 3
The Overall profile which ur using has control profile & this should have presentation type as 04 for Capacity availability check to happen ..
regards
pushpa

HR assignment to Work center

Hi All,
I am having few queries with the above subject.
My customer is asking that he will assign persons(from HR) to the work centers. and based on the assignments done he want some functionality like
1. At the time of operation confirmation through CO11N in the person field only assigned persons(in Work center) should be available
2. At the time of capacity availability check system should check the person attached to work center only. e. g. suppose two persons for 8 hrs are assigned to work center then if order need 18 labor hours, in this case system should tell that capacity is not available. and then if third person added to Work center master then it will tell capacity is available.
Now my question is :
Whether above requirements are possible? if yes then please please tell me how to do?\
Millions of thanks in advance.

Hi Jigar B patel,
Well Work center is the main integration part for both PP and HR OK.
As your requirement is to maintain the responsible person for the work center follow the path:
1) SPRO -
> PRODUCTION -
> BASIC DATA -
> WORK CENTER -
> GENERAL DATA -
> DETERMINE PERSON
    RESPONSIBLE.
2) GO TO THE PARTICULAR WORK CENTER YOU ARE USING THROUGH T-CODE CR02 OR CR03 OK.
    THEN GO TO THE TAB CAPACITIES TAB DOWN THERE ARE PUSH BUTTONS THE VERY FIRST ONE IS CAPACITY BUTTON
    PRESS IT -
> YOU WILL GO TO CAPACITY HEADER SCREEN -
> ON THE TOP YOU CAN FIND PUSH BUTTON CALLED
    AVAILABLE CAPACITY PROFILE -
> ON THE TOP OF THE YOU CAN SEE A GRAPHIC PRESS IT THERE YOU CAN GET AN
    IDEA OK.
   I hope it helps you.
Regards,
Madhu.G

Default employee cost center based on work center

Greetings,
How can I default an employee's home cost center in IT0001 based on their work center assignment?
I've tried linking both the employee's position and their org unit to the work center via CR02. This did create the IT1001 records. The work center does have a corresponding HR work center. I've even tried attaching a cost center to the HR work center with the IT1001-A011 relationship. No luck.
Seems like OM side is doing what it should, but we want to get the work center's cost center in the costing tab over to the employee.
Maybe there's an integration switch that I'm missing somewhere?
Thank you!

Thank you both for your thoughts. We have tried the ZXPADU0x exits, but it appears that SAP will not allow us to change an existing cost center value in IT0001 via defaults. I think this is because SAP wants to always keep OM and PA in sync, based on the A011 relationships in IT1001 on the position or org unit.
In terms of OP42, yes, we have tried adding relationships between the work center and position/org unit and also employee. And also have the cost center linked to the work center on the costing tab. But we're still not able to get that cost center to pull into IT0001.
I'm wondering if the integration between work centers and HCM is limited to relationship links on the OM side?

Work Center Integration PM-PP

Similar Messages

Maybe you are looking for