3702i only getting 10MB/s transfer speed

I am in the process of configuring a 3702i access point, but I am running into an issue where I cannot get over 10MB/s. I have the access point plugged into a gigabit port and have a power adapter plugged into the 3702i since I do not have a POE+ capable switch. I only get around 5MB/s on 2.4GHz radio and 10MB/s on the 5GHz radio which is not any faster than our old aironet 1100 AP. I have tried messing with the data rates but it does not make a difference. The properties on my wireless card show that the connection speed is 217Mbps.
Below is the switchport settings and I attached my configuration file if that helps at all.
4506-2#show run interface gi6/48
Building configuration...
Current configuration : 213 bytes
interface GigabitEthernet6/48
 switchport access vlan 95
 switchport trunk encapsulation dot1q
 switchport trunk native vlan 95
 switchport trunk allowed vlan 94,95
 switchport mode trunk
 no cdp enable
end

After changing the channel width to 80MHz I get an average of 17MB/s transfer speed and it shows that my connection speed is 405Mbps which should give me around 50MB/s.
Wired I get an average of 100MB/s-112MB/s for my transfer speed
Before Changing to 80MHz
c3702-1#show dot11 associations all-client
Address           : 0024.xxxx.xxxx     Name             : c3702-1
IP Address        : 192.168.95.91      IPv6 Address        : ::
Gateway Address   : 0.0.0.0
Netmask Address   : 0.0.0.0            Interface        : Dot11Radio 1
Bridge-group        : 1
reap_flags_1        : 0x0     ip_learn_type       : 0x0       transient_static_ip : 0x0
Device            : ccx-client         Software Version : NONE
CCX Version       : 4                  Client MFP       : Off
State             : EAP-Assoc          Parent           : self
SSID              : vlan95n
VLAN              : 95
Hops to Infra     : 1                  Association Id   : 1
Clients Associated: 0                  Repeaters associated: 0
Tunnel Address    : 0.0.0.0
Key Mgmt type     : WPAv2              Encryption       : AES-CCMP
Current Rate      : m23-               Capability       : WMM 11h
Supported Rates   : 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0-2 m1-2 m2-2 m3-2 m4-2 m5-2 m6-2 m7-2 m8-2 m9-2 m10-2 m11-2 m12-2 m13-2 m14-2 m15-2 m16-2 m17-2 m18-2 m19-2 m20-2 m21-2 m22-2 m23-2
Voice Rates       : disabled           Bandwidth        : 20 MHz
Signal Strength   : -62  dBm           Connected for    : 302 seconds
Signal to Noise   : 35  dB            Activity Timeout : 20 seconds
Power-save        : Off                Last Activity    : 0 seconds ago
Apsd DE AC(s)     : NONE
Packets Input     : 34487              Packets Output   : 51847
Bytes Input       : 2250174            Bytes Output     : 76757696
Duplicates Rcvd   : 1                  Data Retries     : 36241
Decrypt Failed    : 0                  RTS Retries      : 0
MIC Failed        : 0                  MIC Missing      : 0
Packets Redirected: 0                  Redirect Filtered: 0
IP source guard failed : 0             PPPoE passthrough failed : 0
DAI failed : IP mismatch  : 0             src MAC mismatch : 0             target MAC mismatch : 0
Existing IP failed :  0              New IP failed :  0
11w Status       : Off
Session timeout   : 0 seconds
Reauthenticate in : never
After Changing to 80MHz
c3702-1#show dot11 associations all-client
Address           : 0024.xxxx.xxxx    Name             : c3702-1
IP Address        : 192.168.95.91      IPv6 Address        : ::
Gateway Address   : 0.0.0.0
Netmask Address   : 0.0.0.0            Interface        : Dot11Radio 1
Bridge-group        : 1
reap_flags_1        : 0x0     ip_learn_type       : 0x0       transient_static_ip : 0x0
Device            : ccx-client         Software Version : NONE
CCX Version       : 4                  Client MFP       : Off
State             : EAP-Assoc          Parent           : self
SSID              : vlan95n
VLAN              : 95
Hops to Infra     : 1                  Association Id   : 1
Clients Associated: 0                  Repeaters associated: 0
Tunnel Address    : 0.0.0.0
Key Mgmt type     : WPAv2              Encryption       : AES-CCMP
Current Rate      : m23b               Capability       : WMM 11h
Supported Rates   : 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0-2 m1-2 m2-2 m3-2 m4-2 m5-2 m6-2 m7-2 m8-2 m9-2 m10-2 m11-2 m12-2 m13-2 m14-2 m15-2 m16-2 m17-2 m18-2 m19-2 m20-2 m21-2 m22-2 m23-2
Voice Rates       : disabled           Bandwidth        : 40 MHz
Signal Strength   : -67  dBm           Connected for    : 259 seconds
Signal to Noise   : 27  dB            Activity Timeout : 15 seconds
Power-save        : Off                Last Activity    : 5 seconds ago
Apsd DE AC(s)     : NONE
Packets Input     : 77863              Packets Output   : 147266
Bytes Input       : 4979788            Bytes Output     : 221483209
Duplicates Rcvd   : 1                  Data Retries     : 46004
Decrypt Failed    : 0                  RTS Retries      : 0
MIC Failed        : 0                  MIC Missing      : 0
Packets Redirected: 0                  Redirect Filtered: 0
IP source guard failed : 0             PPPoE passthrough failed : 0
DAI failed : IP mismatch  : 0             src MAC mismatch : 0             target MAC mismatch : 0
Existing IP failed :  0              New IP failed :  0
11w Status       : Off
Session timeout   : 0 seconds
Reauthenticate in : never

Similar Messages

  • Why am I only getting 0.24mbs download speed on my ipad over my wifi when my Microsoft laptop is working massively faster?

    Why am I only getting 0.24mbs download speed & 0.47mbs upload speed on my ipad over my wifi when my Microsoft laptop is working massively faster?
    I have a EE BrightBox wifi router and other devices in the house are working perfectly only problem I have is with my Apple products.

    Hi,
    Don't have a Mac, using new ipad,  iPhone 5&4s both with ios7 but it's soo slow, Microsoft laptop is working fine over wifi so it has to be Apple devices that have the problem. Have tried all of the suggested fixes on forums but still no joy.

  • T400 with 5100N intel wireless only getting 72 MB max speed.

    I have a Airlink 101 150N router that works at full speed (150 MB) with all my other N adapters except my new T400 that has a 5100N wireless adapter.  It only gets 72 MB rate max at full signal strength.  Any suggestions?
    Hal
    Solved!
    Go to Solution.

    Found the problem.  Under Device Manager/network adapter/5100, deselect Value/Use default value (20mhz) and set to Auto.  Works MUCH faster now and says 150 Mb.

  • New infinity on macbook only getting 10mbs downloa...

    hi 
    im new here, 
    ive had infinity for 2 weeks and from day 1 have only had speeds of 9mbs-13mbs using an ethernet cable on my mac pro.
    i get the same speeds using wireless too.
    i did speed checks on btwholesale, speedtest.net and lots of others and get the same reading.
    ive called bt customer service in aisa about 4 times now, they sent me out a new hub to swap over, and still get the same speed .. in cat swaped back to the old one coz the new hub was just flashing the power light over and not connecting after a day!
    i called bt again and the line was checked a few times with no error, they said they would get someone to do an in depth check but if they found it was not a bt fault i would be charged !!!!  i did not agree to that!  so they suggested i get another computer to test the download speed using that to illiminate my mac pro as the problem ...
    i dont have another computer .. so thats a problem ... but ive been thinking .. if there was a problem with my mac ethernet connection, shouldnt i still get higher than 9 - 11mbs download speed on my mac using wireless ? 
    its been two weeks .. ive read people on here having problems with bt for over 10 weeks ! so i am prepapred for the long haul
    the engineer set up infinity but when i did a speed check and got 9mbs  he said weel you dont want to believe those speed tests, they arent reliable, its fast isint it, thats all you need !  cheecky **bleep**!
    he said i had to contact bt and sort out the problem there, seemed to be in a hurry :-(
    how can someone here on these boards help that works for bt ?
    any ideas what the problem could be ?... i requested a new router to test and they agreed the day after it was installed but they never sent it ... 
    ive plugged it all in at the master socket and get the same test results .
    i would really love to get close to the 40mbs that bt promised, and the engineer even said i would have no problems getting full speed as the green cabinet was only 150 yards away and the line test he did showed i can easily get 100mbs load on the line
    any help very welcome thanks in advance ...  its making me think theres a problem coz im a mac user :-(
    thanks
    mac user

    ok  
    so i did the profile test thing at speedtester.bt
    results are :
    download speed 11.24 Mbps
     Download speedachieved during the test was - 11.24 Mbps
     For your connection, the acceptable range of speedsis 12 Mbps-38.71 Mbps .
     Additional Information:
     IP Profile for your line is - 38.71 Mbps
    38.71 Mbps
    Max Achievable Speed
    does this help ?  hope so :-)
    what next ?

  • High speed expanded internet t only getting 0.38 upload speed

     I need at least 0.60 upload speed for my new job so i switched isp to Verizon for the expanded highspeed which was supposed to cover that speed (3.84 - 7.84 kpbs they advertise) i need for Hd live stream. when i first set it up it was high enough  but now  it is consistently down to 0.39. I have spoken to 3 robotic online techs who try and tell me this is the fastest i can get in my area and that is a good spped and it is not- on speedtest.net my upload speed of 1.29 mbps and 0.39 mpbs rate a grade of F!
    Fios is not available in my part of l.a  yet but they have it the next neighboorhood oover in snata monica.
    No one will help me fix the problem. When i spoke to billing they said it looked like there was some kind of problem blocking my line but these techs i spoke with can't find it and just go through the script they are taught i suppose.
    can anyone help? my laptop is only a year old and i connect directly to ethernet cable. i defragged and clean computer but no change.
    Help or i am going to have ti try and switch to ATT U verse. My modem is an Actiontech.
    HELP

    Chances are slim if you're in a Verizon area that AT&T U-Verse would be available. AT&T and Verizon typically don't overbuild on each other except in very few, specific circumstances. Besides, I personally wouldn't order U-Verse due to their 300GB/m data cap. DSL Resellers are always an option, but whether or not they can deliver the desired speed is up to the line, up to their equipment or more often than not, up to Verizon.
    For this issue, you may have been "optimized" if you saw the speed you desire earlier. Would you be willing to supply your modem Transceiver Statistics? If you're not sure how to get this, please let me know what your modem make and model is.
    ========
    The first to bring me 1Gbps Fiber for $30/m wins!

  • Only getting 1 meg - slow speeds in shortstown/car...

    I am receving very low speeds on my broadband and im paying close to £36 a month for 1 meg broadband is this acceptable ?

    17:39:39, 08 Jun.
    (12535.210000) Admin login successful by 192.168.1.67 on HTTP
    17:39:18, 08 Jun.
    (12514.990000) Admin login FAILED by 192.168.1.67 on HTTP
    17:38:48, 08 Jun.
    (12484.820000) Admin login FAILED by 192.168.1.67 on HTTP
    17:38:28, 08 Jun.
    (12464.730000) Reset button pressed
    17:37:39, 08 Jun.
    (12415.170000) New GUI session from IP 192.168.1.67
    17:29:17, 08 Jun.
    IN: BLOCK [16] Remote administration (TCP 116.10.191.208:6000->86.162.66.14:22 on ppp0)
    17:25:28, 08 Jun.
    (11684.820000) Lease for IP 192.168.1.67 renewed by host Ash-Laptop (MAC 20:68:9d:da:f0:be). Lease duration: 1440 min
    17:25:28, 08 Jun.
    (11684.820000) Device connected: Hostname: Ash-Laptop IP: 192.168.1.67 MAC: 20:68:9d:da:f0:be Lease time: 1440 min. Link rate: 120.0 Mbps
    17:25:28, 08 Jun.
    (11684.760000) Lease requested
    17:25:28, 08 Jun.
    wlan1: STA 20:68:9d:da:f0:be IEEE 802.11: Client associated
    15:18:53, 08 Jun.
    IN: BLOCK [16] Remote administration (TCP 116.10.191.219:6000->86.162.66.14:22 on ppp0)
    15:12:07, 08 Jun.
    ( 3683.890000) Device disconnected: Hostname: Ash-Laptop IP: 192.168.1.67 MAC: 20:68:9d:da:f0:be
    15:12:05, 08 Jun.
    wlan1: STA 20:68:9d:da:f0:be IEEE 802.11: Client disassociated
    15:10:34, 08 Jun.
    IN: BLOCK [16] Remote administration (TCP 61.174.51.212:6000->86.162.66.14:22 on ppp0)
    14:20:23, 08 Jun.
    IN: BLOCK [16] Remote administration (TCP 112.112.14.70:61206->86.162.66.14:22 on ppp0)
    14:19:48, 08 Jun.
    IN: BLOCK [16] Remote administration (TCP 98.190.1.101:55245->86.162.66.14:22 on ppp0)
    14:15:38, 08 Jun.
    BLOCKED 19 more packets (because of Packet invalid in connection)
    14:15:38, 08 Jun.
    IN: BLOCK [9] Packet invalid in connection (TCP 92.48.71.150:80->86.162.66.14:49767 on ppp0)
    14:15:36, 08 Jun.
    IN: BLOCK [15] Default policy (TCP 107.20.253.239:443->86.162.66.14:49749 on ppp0)
    14:15:34, 08 Jun.
    BLOCKED 6 more packets (because of Default po

  • Recently upgraded my macbook pro 13 late 2009 to an ssd but only getting a quarter of the speed

    Hi, i recently upgraded my macbook pro 13 inch to a OCZ VERTEX 3 240gb ssd. The drive is supposed to be able to have write speeds of 500mb/s and read speeds of up to 550 mb/s but when i run a speed test on the disk im only getting a max write speed of around 105 mb/s, and read speed of 137mb/s ish, now the negotiated speed is only 1.5gb/s I have trim enabled, and i have tried changing the link speed but with no luck. The drive is rated for 6gb/s also. The drive is not in the hard drive bay because my hard drive cable is broken, i have it in the optical bay right now, could someone please help me or tell me how to make the drive at least go up to sata 3 speeds,

    The 2009 MBPs were built with a very cheaply made HDD to LB cable. So I bet if you change that cable you will see more speed from that SSD.

  • Slow transfer speeds between Mac Pro and Shared Drive on Windows Domain

    Hi Guys,
    Getting really slow transfer speeds when I try and transfer a file from a Mac Pro to a shared network drive on one of our Windows 2003 Servers.
    The Mac Pro is logged on to windows domain. This data is transferring via our hard network, not via wireless. Not having any other transfer speed issues on any other PC's.
    For example an 8mb file took around 45 mins.
    Hope you can help. Many Thanks.

    I saw this at a site where they were using DFS with Server 2003. When the few Mac's they had connected to the actual server and uploaded the file it was okay. But when it was sending the file via the \\DFS_node\share_name the Mac took heaps longer for the same file. Watching the Activity Monitor > Network monitor you could see gaps with the data transfer, as if there was some pausing between packets. A pcap showed that there was constant DNS requests coming from the Mac, even after the connection to the share was made. The same wasn't happening when the connection via SMB was directly to the actual file server. As there was only a few Mac on site they left it with the direct connection but were getting an MS specialist in to look at it. Never heard what happened with that one but you may want to try monitoring the packet transfer to see if the data movement is contstant or breaking. I'd also recommend getting Wireshark to monitor the transfer. You can compare upload to download and maybe even the transfer from the Mac to an MS workgroup share.

  • UP to 20mb only getting 5mb. Lied to YET AGAIN by ...

    The 10 day period is now over (it has been 21 days) and I am only getting a constent pathetic speed of 5.5 MBPS. I was given a quote of 'up to 20mb' by the sales representative. As soon as my BB went active on the 28th November I was immeadiatly told by a forum mod that I am only able to get a maximum of 10MBPS. This raises several issues as follows:
    -- THE 20MB QUOTE WAS GIVEN BY:
    1) The sales person I spoke to on the phone.
    2) BT speed checker before I bought the broadband. 
    3) Online when I brought the broadband.
    4) In BOTH of the 'thanks for choosing BT' emails I was sent for me order.
    Below is a screenshot of the relevant part of one of those 2 emails. Please see highlighted quite clearly in red the part saying that it should be 17mbps (I was quoted up to 20mbps but estimated 17mbps).
    Your broadband starts on:
    07 Dec 2011
    Your username is:
    ********.****.*******@btinternet.com
    Your password is:
    Your speed should be:
    17Mb
    Your actual speed might be between10Mb and 19.5Mb - depending on how far you live from your exchange, your home's wiring and a few other things.
    Find out what can affect your speed atwww.bt.com/yourbroadbandspeed
    When your service starts
    Your service can start at any time up to midnight on the day it's due. We'll let you know when it's ready.
    I have just re-run the BT speed checker on my line. Although the speed quoted is lower than I was initially quoted, it still says 6.5 - 15mb, with estimated speed at 10mb. 
    There are quite clearly 2 main issues here:
    1) I was quite clearly missold the 'up to' speed of 20mb.
    2) The broadband speed I am currently receiving is even lower than the NEW low speed estimates.
    Please can you investigate this further for me because not only was I seriously messed around by BT for a month getting the broadband installed, now I find out that I am only receiving a QUARTER of what I was originally quoted.
    PLEASE CAN A FORUM MOD PICK THIS ISSUE UP FOR ME AS DO NOT WANT ANY CONTACT WITH THE INDIA CALL CENTRE AGAIN AFTER MY BB SET UP FIASCO!!!!

    Hi Welcome to the forums
    If you post the full stats from your router
    For homehub – type 192.168.1.254 into your browser
    Navigate to ADSL Settings or use the A-Z at the top right of the home page and scroll down to ADSL Settings and click on it
    Click on More Details and then post the full results.
    also post the full results from http://speedtester.bt.com/
    Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
    also you could try the hints given by poster RogerB in this link they may help http://community.bt.com/t5/BB-in-Home/Poor-Broadba​nd-speed/m-p/14217#M8397
    Then someone here may be able to help and offer more advice.
    This is a customer to customer self help forum the only BT presence here are the forum moderators
    If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

  • Getting 1/2 the speed I'm paying for & in too much pain to be on phone for hours--HELP

    My children do a Cyber school and have been getting disconnected from class for months now.  I'm also having losing the internet at random times on my desktop. A friend told me how to check my speed (since I know so little about computers) and I found out I'm only getting 1/2 the speeds I'm paying for!!!!  I've called Verizon customer service in WHATEVER COUNTRY 6 times now but I have to hang up after any longer than 35 minutes because of chronic pain!  Tech makes me turn off my router, check my speed, (when I know they can see the speed right in front of them, after 1 rep told me the speed without my asking) and computer share.   Nothing gets resolved, I NEVER GET THE CALL FROM A SUPERVISOR THAT WAS PROMISED, and Verizon closes out the problem after 72 hours!!  Seems  like EVERYONE ELSE HERE GETS THE SAME RUNAROUND AND LACK OF RESPECT!!  One billing person offered me a refund for the difference in speed for only 1 month and offered me to upgrade!!  I can't afford to upgrade and the Cyber will work if I would only get the speed I had when 1 started with Verizon in 2002!  I said UNACCEPTABLE and am having to call back once a week (because that's all I can handle)  to try to get a Supervisor!  Can anyone tell me how to get help without the exhaustion of being on the phone forever?! 
         All I know is I'm paying for 1.1-3 mbps but only getting .439-.864mbps download and 0.08-0.09 upload speeds and I have a Westfall 327W 8 year old modem.

    Thank you for replying and sorry it took so long to respond.  Now I can't get into my Verizon email so I didn't know I had a response on this site. I was also physically unable to sit at my computer.  Here is the info you requested:
    Transceiver Revision: 7.2.3.0   Vendor ID Code: 4   Line Mode: G.DMT Mode   Data Path: Interleaved     Transceiver Information Downstream Path Upstream PathDSL Speed (Kbits/Sec) 864 160 Margin (dB) 20.5 31.0 Line Attenuation (dB) 44.5 29.0 Transmit Power (dBm) 3.3 11.1
    on 8/15 I had the slowest download speed yet of 0.17 mbps! I am paying for 1.1-3mbps.  My modem is 6 or 7 years old.  I'm not sure if I mentioned the last 2 sentences before.

  • EA6500 - 50mb Internet Connection only gets half

    I've got an EA6500 and I've got a 50mb internet connection, but when I connect tru the EA6500 I only get half of the speed but if I connect to my isp router I get the full speed

    Yes, I{ve done all those tests, the isp is comcast.
    I{m using wireless mainly, so If I connect to the EA6500 I only get half of the speed no matter what, ethernet or wireless is the same, I even changed the WWM configuration and its off now.
    http://homecommunity.cisco.com/t5/Wireless-Routers/QoS-and-WMM-settings-slow-internet-down-when-enab...
    The ISP is comcast, and Im using gigabit ports, and for wireless N.

  • I have bought my iphone 5 from UK and now residing in USA. Although my carrier (Ultra Mobile) provides 4G service i only get 3G speed. Also icon "3G" appears on top part of my screen. My model is MD297B/A. Pls suggest to enable 4G on my phone

    i have bought my iphone 5 from UK and now residing in USA. Although my carrier (Ultra Mobile) provides 4G service i only get 3G speed. Also icon "3G" appears on top part of my screen. My model is MD297B/A. Pls suggest to enable 4G on my phone

    It is more than likely the inability of the UK phone to support the US phone bands. You will probably be stuck with 3G and will never be able to get LTE. Also, your warranty is only good in the UK. You might be better of to try and sell that device to someone in the UK and purchase a phone in the US that you can get full service with.

  • Hello, i just installed a vertex 2e 90gb ssd in my macbook pro 13" (8.1 early 2011). But when i do a disk speed test i only get 125 mb/s write speed and 146 mb/s read speed.

    Hello, i just installed a vertex 2e 90gb ssd in my macbook pro 13" (8.1 early 2011). But when i do a disk speed test i only get 125 mb/s write speed and 146 mb/s read speed. Thats under 50% of what i should get. The disk have firmware 1.35 and 3 gb/s linkspeed when i check in systemreport.
    Anyone know why i get so low speed from my ssd?

    Speak to the manufacturer. They did the bench tests.

  • Upgraded to Blast105 from 25mbps but im Only getting speed only around 20-25 Mbps

    I upgraded earlier this week and I dont seem to get close to the speed im paying for The best I ever got was 42mbps and 12 upload.... whats should I do?

    Also make sure you are testing on a wired connection and not wireless. 
    If you're wired
    have optimized your connection (you can also use the in home agent to optimize and test your connection)
    and are testing at verizon's speedtest site (as the previous poster stated, a lot of speedtest.net's servers choke at 7 mb up) then there is no reason you shouldn't be, not only getting your speed, but slightly higher.    If all those things are true, then you should call back in for possible router replacement, or to have them look at their network again.  make sure to call when you are actually getting bad speeds at speedtest.verizon.net
    most users get what they pay for and more,  fiber is light.  it's either on or off.  it doesn't really go slow, so if it TRULY is slow, it could be something at your house, or something far out on the back end.  
    if the xbox is on wireless, then you may want to seriously consider getting a moca bridge for that room. 
    it will provide you with a hardwired connection that won't suffer from a lot of the fluctuations that wireless have. 
    Cheap solutions if it's wireless, is to spend 25 bux and get a wireless n upgrade to your actiontec router through trendnet's nifty little device (it will be faster than your wireless now, but ymmv)
    or get a moca adapter.  today is the last day for their special 99 bux for two moca adapters.  you basically get a tv splitter, one side of the splitter goes to your tv, the other side to this adapter.  the input of the adapter is coax, the output is ethernet. 

  • External hard drive, error -36, corrupt files and slow transfer speeds

    This is a long post but stay with me.
    I've got an external 250GB Lacie drive connected to my 24" Intel iMac via Firewire 800. I have approximately 80GB worth of files (including my iPhoto library) on the Lacie that I'm trying to move over to my iMac but have run into some frustrating problems.
    Overall, transfer speeds are erratic – fine at times and SUPER SLOW (5 minutes to transfer a 3MB file) at other times. At first I was transferring entire folders, but after always getting errors (error -36 to be exact), I was having to transfer individual files. This works fine as long as the files aren't too big (which makes the transfer speeds SUPER SLOW) and not corrupt (which gets me an error -36). Is my Lacie crashing on me? Is there any hope?
    Here's what I've done to try and salvage my sanity with no resolve to my problems (not exactly in this order):
    1) Ran Disk Utility to repair Lacie. Everything came back OK
    2) Ran Disk Warrior on Lacie. Found a handful of bad items that Disk Warrior was able to repair. Had Disk Warrior replace the old directory of the Lacie with the new directory.
    3) Ran Drive Genius: Raired and Rebuilt the directory, did an Integrity Check (came back OK), attempted to Defrag but could not because of errors to the drive, did a Scan for bad blocks (which after running for 3 days! it was only 20% complete and had found over 150 bad blocks, at which point I quit to try something else)
    4) Checked that my Firewire cable was properly connected and replaced the older one I was using with a brand new one.
    5) Disconnected all peripherals except for keyboard, mouse and Lacie.
    6) And at times, even viewing a file on the Lacie has caused my Finder to crash, requiring a restart of my iMac.
    I'm sure I've left something off I've tried but you get the idea.
    I've read that maybe I can transfer my files using Terminal. Yes/No? Does this bypass any corruption the files may have?
    What about creating a second partition on the Lacie and moving files over to the second partition? Does this solve anything? I don't know anything about partitioning so maybe I'm talking crazy.
    I've also read that iPhoto tends to corrupt files which makes me hate iPhoto, and myself for not backing up.
    And I've read a lot about error -36's and none of it sounds good so I'm just hoping that someone might have other suggestions for me to try and save my files (especially my iPhoto files which include baby pictures that if I lose, my wife will kill me).
    So if anyone has any ideas, let me know. Please. I'll try anything.

    Hi Aaron Thompson-
    I am fairly certain you have a bad power supply brick to the LaCie drive. This is a hard problem to troubleshoot as generally when the bricks go bad they do so slowly and the drive appears to power up and stuff but it just doesn't work.
    If the drive is under warranty LaCie will replace the brick at no charge. Otherwise they sell them for around $20US on their website.
    Luck-
    -DP

Maybe you are looking for