Bursting to fax not in landscape

I have a burst control file that emails, prints and faxes pdf with one problem.
When sent to the fax as landscape it faxes as portrait - printers and email are ok.
I am running CUPS with Hylafax if that helps
Bob Harrison

Samir just another note to avoid time left in your implementation;
If your fax server can redirect email to fax ensure that it can process the carbon copy field of the email because xmlp put the recipient only in this field.
Remeber to set this post as answered and take the time join www.j4jde.com network.
Regards
Bruno Condemi

Similar Messages

Fax not detected,Comm error, fax run test is all PASS,

Hi Good Day! Im Using a HP color Laserjet Pro MFP M177fw. The Problem is sending fax messages. I do all the updates you need to installed. but the problem with my hp fax machine is still there specially i still receive a fax not detected issue,comm.error, but when i run the fax test run..the result is all PASS. especially the active tel.line,correcrt port on fax machine,tel line current test,dial tone..all the question and are PASS. The firmware is updated like..20140914. Please help me for this kind of problem. Thank You!

Hi @ali_al , I can help you with the fax not being able to send faxes.
Check these settings on the printer:
Confirm the fax number:
Go to setup, fax setup, advanced setup, confirm fax #.
Turn off error correction:
Go to setup, service, fax service, error correction and turn if off.
Set the fax speed to medium:
Go to setup, fax setup, advanced setup, fax speed and select medium.
Turn off the private receive:
Go to setup, fax setup, advanced setup, private receive. Turn it off.
Test the fax.
I have provided a document with some steps to try to see if that will resolve the issue.
Cannot Send or Receive Faxes.
Please provide the following information so I can assist you better.
What type of connection do you have? (Analogue, DSL, Cable Modem)
Are you using the 2 wire phone cable?
Do you have distinctive ring set up on the line?
Is there any voice mail set up?
Do you have a answering machine? (Where is it connected to?)
Where is the fax cable connected to? (modem, wall jack)
Is there a phone also connected the printer?
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Not getting Landscape format while printing the file.

I am not getting Landscape format while printing the file. I am using the follwing code. Can anyone help me in this regard. its urgent.
public void printText(){
String outputPath="d:\\output\\";
DocFlavor flavor = DocFlavor.INPUT_STREAM.POSTSCRIPT;
PrintRequestAttributeSet aaset = new HashPrintRequestAttributeSet();
DocumentName docName = new DocumentName(outputPath+"outfile.ps", Locale.US);
PrintService pservices = PrintServiceLookup.lookupDefaultPrintService();// lookupPrintServices(flavor,aset);
try {
DocPrintJob pj = pservices.createPrintJob();
InputStream file = new BufferedInputStream(new FileInputStream(outputPath+"outfile.ps"));
Doc doc = new SimpleDoc(file,flavor,null);
try {
     aaset.add(MediaSizeName.ISO_A4);
     aaset.add(OrientationRequested.LANDSCAPE);
     aaset.add(Sides.DUPLEX);
     pj.print(doc,aaset);
     } catch (PrintException e1) {
          e1.printStackTrace();
     } catch (FileNotFoundException e) {
     e.printStackTrace();
}

As a quick workaround... put the paper in the other way

Bursting - empty tag not being cleared in email channel loop

If you check the following, I pass the cust num and email address to the email delivery channel for the subject line.
<xapi:message id="222" to="[email protected]" attachment="true" subject="Unigas Statement to be emailed to ${CUST_NUM} to ${EMAIL}">
Problem is, that if the cust num or email address tag is empty, the previous tag value is used! its like its not being "cleared" between bursting loops.
Using 5.6.3 EBS.
Rob
http://www.scnet.com.au

Since your email is failing I am going to assume the rest of your script is working. So I am looking specifically at these lines:
$process = '../includes/process_mail.inc.php';
if (file_exists($process) && is_readable($process)) {
include($process);
The things that need to be confirmed here are that the path is right and it has proper permissions. Have you tried eliminating that "and" statement in your "if" and see if those work independently. I have a feeling that if the path is right that the file does not have the proper permissions on your server for global read access which would make, "is_readable" fail and thus end your script.
Can you test those and post back?

Output fax not getting triggered when sales order credit block is released

Hi Experts,
I am working on an issue.
I have one sales Order which has credit block.
when we release the credit block via vkm3, then the output fax gets triggered.
I have another sales order which has credit block,
when we release the credit blcok via vkm3 , the output fax is NOT getting triggered.
If any of you has worked on this setting, request your input on where to find the settings/coding for the same.
Any advice on this please.
Regs,
SuryaD.
Edited by: SuryaD on Oct 21, 2010 9:34 PM

Hi Brad,
Thanks for your response.
Order 1: Issues output fax(ZFAX) correctly when block is released.(i see output zfax in te output screen)
Order 2: Fails to issue output fax(ZFAX) even when the block is released.( i dont see any output in the output screen)
I went to Go to -Determine analysis for both orders 1 and order 2.
in both the analysis i am able to see the output ZFAX.
*Analysis Output*
*Order 1                                                                    Order 2*
1. ZFAX                                                                   1.   ZFAX
    10(Z010)                                                                 10(Z010)
       0000122426                                                              0000122427
2. ZFAX                                                                   2.   ZFAX
When i click, D.Click on the output type ZFAX on both the order Analysis output screen, i see similarities.
There in just 2 differences as below.
In the above screen,
1.Order 1 ==> has some value 0000122426
2.For Order 1==> row marked 2.(in the above screen) if i D.Click on ZFAX it says
Diagnosis
Output ZFAX has already been issued. Multiple issue for this output type is forbidden in Customizing.
In the above screen
1.Order 2 ==> has some value 0000122427
2.For Order 2==> row marked 2.(in the above screen) if i D.Click on ZFAX it says
No more information is available.
Please guide as to how to initiate the debug for output processing ?
Which screen where to switch on debugger.
where to look further?
Regards,
SuryaD.
Edited by: SuryaD on Oct 22, 2010 11:41 AM

Can't Send FAX / FAX not working

Dear Techies,
I am facing a horrible problem in sending FAX. In our company, our directors are using MAC Book Air & Mac Book. I have a MAC Book too (i am a newbie to MAC), which they had given me for testing purpose, so that i should clear all their problems in MAC. so its actually a tough thing...
Now, they are not able to send FAX from these machines. They asked me to provide them the solution, and i tried in and out in my MAC Book, But no way... I googled a lot, i found many of the discussions based on this issue, but i didnt saw any working solution for it. Now its the 3rd day for me to sit with this issue. Hope someone will be here to help me. Let me give you the details...
Hardware: MAC book and Mac Book Air
OS: MAC OS X Version 10.4.10
CPU: 2.16 Ghz Intel Core Duo
Mem: 2 GB 667Mhz DDR2
MODEM: External Apple USB modem
Scenario 1:
I tried sending the fax from safari (File--> Print--> Fax PDF), then specified our internal FAX number, also Dialing prefix as 9(bcoz i am behind a EPABX, so 9 to get dial tone)
To: 63452743 (Fax number, not original)
Dialing Prefix: 9
Dialing: Tone (selected)
Sound: on (selected)
Wait for dial tone before dialing: selected
then i clicked "FAX"
but the result was; FAILURE...
Result 1:
It will dial, and stands like connected, while showing a progress bar "Faxing" in the external modem window. after around 3 minutes, it stops... and shows the following message in the external modem window;
"hold until 05:01 p.m."
again it will try at that specified time, and the result is same.
Scenario2:
I tried with fax command;
fax send 9-66728437 test-file.001
and i tried
fax send 966728437 test-file.001
Result2:
It will also do the same like above and finally gives up, and then it will write a log as the following;
command;
abcs-computer:~ kmr$ sudo fax send 9-66766766 test-file.001
Password:
efax v 0.9a-001114 Copyright 1999 Ed Casas. Compiled Apr 24 2007 20:31:43
efax: Tue Aug 12 17:03:17 2008 opened /dev/cu.usbmodem
efax: 03:18 using Motorola SM56 USB 1.5.6 in class 1
efax: 03:19 dialing T9-667667667
efax: 05:19 Error: dial command failed
efax: 05:19 failed -> test-file.001
efax: 05:19 done, returning 2 (unrecoverable error)
There were errors (see T9-667667667.log).
abcs-computer:~ kmr$
Log;
efax v 0.9a-001114 Copyright 1999 Ed Casas. Compiled Apr 24 2007 20:31:43
efax: Tue Aug 12 17:03:15 2008 TIFF version 4.2 file (little-endian)
efax: 03:15 TIFF directory at 8 with 17 tags, last image.
efax: 03:15 page 1 : test-file.001 + 234 : 1728x2156 @ 204x196 dpi TIFF/FAX
efax: 03:15 argv[0]=efax
efax: 03:15 argv[1]=-v
efax: 03:15 argv[2]=ewin
efax: 03:15 argv[3]=-v
efax: 03:15 argv[4]=chewmainrxtf
efax: 03:15 argv[5]=-d/dev/cu.usbmodem
efax: 03:15 argv[6]=-iZ
efax: 03:15 argv[7]=-i&FE0&D2S7=120
efax: 03:15 argv[8]=-i&C0
efax: 03:15 argv[9]=-iM1L0
efax: 03:15 argv[10]=-o1
efax: 03:15 argv[11]=-l
efax: 03:15 argv[12]=495 2322999
efax: 03:15 argv[13]=-kZ
efax: 03:15 argv[14]=-h
efax: 03:15 argv[15]=2008/08/12 17:03 495 2322999 Put Your Name Here p. %d/%d
efax: 03:15 argv[16]=-t
efax: 03:15 argv[17]=T9-667667667
efax: 03:15 argv[18]=test-file.001
efax: 03:17 opened /dev/cu.usbmodem
efax: 03:17 command "Q0V1"
efax: 03:17 waiting 2.0 s
efax: 03:17 .170 [ATQ0V1<CR><CR><LF>]
efax: 03:17 .401 [OK<CR><LF>]
efax: 03:17 response "OK"
efax: 03:17 command "Z"
efax: 03:17 waiting 5.0 s
efax: 03:17 .501 [ATZ<CR><CR><LF>]
efax: 03:17 .577 [OK<CR><LF>]
efax: 03:17 response "OK"
efax: 03:17 command "&FE0&D2S7=120"
efax: 03:17 waiting 5.0 s
efax: 03:17 .677 [AT&FE0&D2S7=120<CR><CR><LF>]
efax: 03:17 .903 [OK<CR><LF>]
efax: 03:17 response "OK"
efax: 03:18 command "&C0"
efax: 03:18 waiting 5.0 s
efax: 03:18 .078 [<CR><LF>OK<CR><LF>]
efax: 03:18 response "OK"
efax: 03:18 command "M1L0"
efax: 03:18 waiting 5.0 s
efax: 03:18 .304 [<CR><LF>OK<CR><LF>]
efax: 03:18 response "OK"
efax: 03:18 command "E0"
efax: 03:18 waiting 5.0 s
efax: 03:18 .505 [<CR><LF>OK<CR><LF>]
efax: 03:18 response "OK"
efax: 03:18 command "I3"
efax: 03:18 waiting 5.0 s
efax: 03:18 .630 [<CR><LF>Motorola SM56 USB 1.5.6<CR><LF>]
efax: 03:18 .655 [<CR><LF>OK<CR><LF>]
efax: 03:18 response "OK"
efax: 03:18 command "+FCLASS=1"
efax: 03:18 waiting 5.0 s
efax: 03:18 .850 [<CR><LF>OK<CR><LF>]
efax: 03:18 response "OK"
efax: 03:18 using Motorola SM56 USB 1.5.6 in class 1
efax: 03:18 command "+FTM=?"
efax: 03:18 waiting 5.0 s
efax: 03:18 .975 [<CR><LF>3,24,48,72,73,74,96,97,98,121,122,145,146<CR><LF>]
efax: 03:19 .000 [<CR><LF>OK<CR><LF>]
efax: 03:19 response "OK"
efax: 03:19 command "+FAR=1"
efax: 03:19 waiting 5.0 s
efax: 03:19 .126 [<CR><LF>ERROR<CR><LF>]
efax: 03:19 response "ERROR"
efax: 03:19 dialing T9-667667667
efax: 03:19 command "DT9-667667667"
efax: 03:19 waiting 120.0 s
efax: 05:19 Error: dial command failed
efax: 05:19 failed -> test-file.001
efax: 05:19 command "Q0V1"
efax: 05:19 waiting 2.0 s
efax: 05:19 .325 [<CR><LF>OK<CR><LF>]
efax: 05:19 response "OK"
efax: 05:19 command "Z"
efax: 05:19 waiting 5.0 s
efax: 05:19 .500 [<CR><LF>OK<CR><LF>]
efax: 05:19 response "OK"
efax: 05:19 done, returning 2 (unrecoverable error)
==========
Scenario 3:
i tried sending the Fax with efax command too;
efax -d /dev/cu.usbmodem -o a -v ewincm -t T9667667667 ts-fax.001
The result is same too...
command and log on the screen;
abcs-computer:~ kmr$ efax -d /dev/cu.usbmodem -o a -v ewincm -t T9667667667 ts-fax.001
efax v 0.9a-001114 Copyright 1999 Ed Casas. Compiled Apr 24 2007 20:31:43
efax: Tue Aug 12 13:38:44 2008 Warning: bind returned error 13 - Permission denied
efax: 38:44 opened /dev/cu.usbmodem
efax: 38:44 command "Q0V1"
efax: 38:44 waiting 2.0 s
efax: 38:44 .482 [ATQ0V1<CR><CR><LF>]
efax: 38:44 .714 [OK<CR><LF>]
efax: 38:44 response "OK"
efax: 38:44 command "E0"
efax: 38:44 waiting 5.0 s
efax: 38:44 .840 [ATE0<CR><CR><LF>]
efax: 38:44 .915 [OK<CR><LF>]
efax: 38:44 response "OK"
efax: 38:45 command "I3"
efax: 38:45 waiting 5.0 s
efax: 38:45 .066 [<CR><LF>Motorola SM56 USB 1.5.6<CR><LF>]
efax: 38:45 .091 [<CR><LF>OK<CR><LF>]
efax: 38:45 response "OK"
efax: 38:45 command "+FCLASS=?"
efax: 38:45 waiting 5.0 s
efax: 38:45 .241 [<CR><LF>0,1,8<CR><LF>]
efax: 38:45 .266 [<CR><LF>OK<CR><LF>]
efax: 38:45 response "OK"
efax: 38:45 command "+FCLASS=1"
efax: 38:45 waiting 5.0 s
efax: 38:45 .467 [<CR><LF>OK<CR><LF>]
efax: 38:45 response "OK"
efax: 38:45 using Motorola SM56 USB 1.5.6 in class 1
efax: 38:45 command "+FTM=?"
efax: 38:45 waiting 5.0 s
efax: 38:45 .618 [<CR><LF>3,24,48,72,73,74,96,97,98,121,122,145,146<CR><LF>]
efax: 38:45 .643 [<CR><LF>OK<CR><LF>]
efax: 38:45 response "OK"
efax: 38:45 command "+FAR=1"
efax: 38:45 waiting 5.0 s
efax: 38:45 .793 [<CR><LF>ERROR<CR><LF>]
efax: 38:45 response "ERROR"
efax: 38:45 dialing T6666666
efax: 38:45 command "DT6666666"
efax: 38:45 waiting 120.0 s
efax: 40:45 .017 [<CR><LF>NO CARRIER<CR><LF>]
efax: 40:45 response "NO CARRIER"
efax: 40:45 Error: dial command failed
efax: 40:45 failed -> ts-fax.001
efax: 40:45 command "Q0V1"
efax: 40:45 waiting 2.0 s
efax: 40:45 .262 [<CR><LF>OK<CR><LF>]
efax: 40:45 response "OK"
efax: 40:45 command "H"
efax: 40:45 waiting 5.0 s
efax: 40:45 .413 [<CR><LF>OK<CR><LF>]
efax: 40:45 response "OK"
efax: 40:45 done, returning 2 (unrecoverable error)
abcs-computer:~ kmr$
And also one more information from /var/log/cups/error.log
I [12/Aug/2008:17:01:24 +0300] Started filter
/usr/libexec/cups/filter/cgpdftoraster (PID 275) for job 12.
I [12/Aug/2008:17:01:24 +0300] Started filter
/usr/libexec/cups/filter/rastertotiff (PID 276) for job 12.
I [12/Aug/2008:17:01:24 +0300] Started backend
/usr/libexec/cups/backend/fax (PID 277) for job 12.
I [12/Aug/2008:17:02:28 +0300] Saving printers.conf...
I [12/Aug/2008:17:02:28 +0300] Printer 'External_Modem' stopped by ''.
E [12/Aug/2008:17:02:28 +0300] PID 277 stopped with status 1!
I [12/Aug/2008:17:02:28 +0300] Hint: Try setting the LogLevel to
"debug" to find out more.
So thats all about all my trials and result.... Please help me to get out of this bad situation...
NOTE: I had changed the original FAX number from this post to different numbers...
Thats all...
Thanks in Advance...
and really awaiting for your valuable comments.

First of all, really thanking you 3 for your posts. i dont need to do a internet faxing. The safari, which i mentioned, in the scenario is an example. My director might need to send FAX from doc files, html files, mails, pdf files etc.
So i need a solution to do the FAX through FAX pdf, which is available through printing.
Then regarding the analog vs digital PBX, here we use analog and digital PBX. But i am trying through the analog line. Still, today i went to the telephone people and asked to give me an direct line to check this out. Then i tried from it.
Fax command and faxing through graphical (fax pdf) gives the same error. But efax command showed a different kind of error message which i will post it here... So i think i will have to work on it... so i requested the telecommunication people to give me an direct line to my table for 2-3 days, so that i could run many test on it... but still i am waiting for their confirmation.
Anyway pls have a look at this message, and put forward ur suggestions.
NOTE: i forgot to notify in the previous post that, the main error point in the log files is "NO CARRIER"
Output of command efax:
abcs-computer:~ root# efax -d /dev/cu.usbmodem -o a -v ewincm -t T7777777 /Users/kmr/test-file.001
efax v 0.9a-001114 Copyright 1999 Ed Casas. Compiled Apr 24 2007 20:31:43
efax: Wed Aug 13 09:25:03 2008 opened /dev/cu.usbmodem
efax: 25:04 command "Q0V1"
efax: 25:04 waiting 2.0 s
efax: 25:04 .097 [ATQ0V1<CR><CR><LF>]
efax: 25:04 .330 [OK<CR><LF>]
efax: 25:04 response "OK"
efax: 25:04 command "E0"
efax: 25:04 waiting 5.0 s
efax: 25:04 .456 [ATE0<CR><CR><LF>]
efax: 25:04 .531 [OK<CR><LF>]
efax: 25:04 response "OK"
efax: 25:04 command "I3"
efax: 25:04 waiting 5.0 s
efax: 25:04 .682 [<CR><LF>Motorola SM56 USB 1.5.6<CR><LF>]
efax: 25:04 .707 [<CR><LF>OK<CR><LF>]
efax: 25:04 response "OK"
efax: 25:04 command "+FCLASS=?"
efax: 25:04 waiting 5.0 s
efax: 25:04 .857 [<CR><LF>0,1,8<CR><LF>]
efax: 25:04 .882 [<CR><LF>OK<CR><LF>]
efax: 25:04 response "OK"
efax: 25:04 command "+FCLASS=1"
efax: 25:04 waiting 5.0 s
efax: 25:05 .083 [<CR><LF>OK<CR><LF>]
efax: 25:05 response "OK"
efax: 25:05 using Motorola SM56 USB 1.5.6 in class 1
efax: 25:05 command "+FTM=?"
efax: 25:05 waiting 5.0 s
efax: 25:05 .234 [<CR><LF>3,24,48,72,73,74,96,97,98,121,122,145,146<CR><LF>]
efax: 25:05 .259 [<CR><LF>OK<CR><LF>]
efax: 25:05 response "OK"
efax: 25:05 command "+FAR=1"
efax: 25:05 waiting 5.0 s
efax: 25:05 .409 [<CR><LF>ERROR<CR><LF>]
efax: 25:05 response "ERROR"
efax: 25:05 dialing T7777777
efax: 25:05 command "DT7777777"
efax: 25:05 waiting 120.0 s
efax: 25:20 .008 [<CR><LF>CONNECT<CR><LF>]
efax: 25:20 response "CONNECT"
efax: 25:20 connected
efax: 25:21 waiting 2.0 s
efax: 25:21 .257 [<CR><LF>OK<CR><LF>]
efax: 25:21 response "OK"
efax: 25:21 received UNKNOWN
efax: 25:21 Warning: bit-reversed HDLC frame, reversing bit order
efax: 25:21 command "+FRH=3"
efax: 25:21 waiting 35.0 s
efax: 25:21 .357 [<CR><LF>CONNECT<CR><LF>]
efax: 25:21 response "CONNECT"
efax: 25:21 waiting 2.0 s
efax: 25:21 .959 [<CR><LF>OK<CR><LF>]
efax: 25:21 response "OK"
efax: 25:21 received CSI - answering ID
efax: 25:21 remote ID -> +000 2 7777777
efax: 25:21 command "+FRH=3"
efax: 25:21 waiting 35.0 s
efax: 25:22 .054 [<CR><LF>CONNECT<CR><LF>]
efax: 25:22 response "CONNECT"
efax: 25:22 waiting 2.0 s
efax: 25:22 .355 [<CR><LF>OK<CR><LF>]
efax: 25:22 response "OK"
efax: 25:22 received DIS - answering capabilities
efax: 25:22 remote has no document(s) to send, and can receive
efax: 25:22 local 196lpi 14.4kbps 8.5"/215mm any 1D - - 0ms
efax: 25:22 remote 196lpi 14.4kbps 8.5"/215mm any 2D ECM-64 - 20/10ms
efax: 25:22 session 196lpi 14.4kbps 8.5"/215mm any 1D - - 10ms
efax: 25:22 command "+FTH=3"
efax: 25:22 waiting 3.1 s
efax: 25:23 .358 [<CR><LF>CONNECT<CR><LF>]
efax: 25:23 response "CONNECT"
efax: 25:23 sent TSI - caller ID
efax: 25:23 waiting 13.6 s
efax: 25:25 .109 [<CR><LF>CONNECT<CR><LF>]
efax: 25:25 response "CONNECT"
efax: 25:25 sent DCS - session format
efax: 25:25 waiting 13.6 s
efax: 25:25 .479 [<CR><LF>OK<CR><LF>]
efax: 25:25 response "OK"
efax: 25:25 command "+FTM=145"
efax: 25:25 waiting 3.1 s
efax: 25:25 .604 [<CR><LF>CONNECT<CR><LF>]
efax: 25:25 response "CONNECT"
efax: 25:25 Warning: termios.iflag is 000000005, not 000001005
efax: 25:25 Warning: terminal mode not set properly
efax: 25:25 waiting 30.0 s
efax: 25:28 .708 [<CR><LF>OK<CR><LF>]
efax: 25:28 response "OK"
efax: 25:28 sent TCF - channel check of 2700 bytes
efax: 25:28 command "+FRS=1"
efax: 25:28 waiting 3.0 s
efax: 25:28 .783 [<CR><LF>OK<CR><LF>]
efax: 25:28 response "OK"
efax: 25:28 command "+FRH=3"
efax: 25:28 waiting 3.0 s
efax: 25:31 waiting 2.0 s
efax: 25:31 .832 [<CR><LF>OK<CR><LF>]
efax: 25:31 response "OK"
efax: 25:31 local 196lpi 14.4kbps 8.5"/215mm any 1D - - 0ms
efax: 25:31 remote 196lpi 14.4kbps 8.5"/215mm any 2D ECM-64 - 20/10ms
efax: 25:31 session 196lpi 14.4kbps 8.5"/215mm any 1D - - 10ms
efax: 25:31 command "+FTH=3"
efax: 25:31 waiting 3.1 s
efax: 25:32 .829 [<CR><LF>CONNECT<CR><LF>]
efax: 25:32 response "CONNECT"
efax: 25:32 sent TSI - caller ID
efax: 25:32 waiting 13.6 s
efax: 25:34 .579 [<CR><LF>CONNECT<CR><LF>]
efax: 25:34 response "CONNECT"
efax: 25:34 sent DCS - session format
efax: 25:34 waiting 13.6 s
efax: 25:34 .931 [<CR><LF>OK<CR><LF>]
efax: 25:34 response "OK"
efax: 25:34 command "+FTM=145"
efax: 25:34 waiting 3.1 s
efax: 25:35 .056 [<CR><LF>CONNECT<CR><LF>]
efax: 25:35 response "CONNECT"
efax: 25:35 Warning: termios.iflag is 000000005, not 000001005
efax: 25:35 Warning: terminal mode not set properly
efax: 25:35 waiting 30.0 s
efax: 25:38 .156 [<CR><LF>OK<CR><LF>]
efax: 25:38 response "OK"
efax: 25:38 sent TCF - channel check of 2700 bytes
efax: 25:38 command "+FRS=1"
efax: 25:38 waiting 3.0 s
efax: 25:38 .231 [<CR><LF>OK<CR><LF>]
efax: 25:38 response "OK"
efax: 25:38 command "+FRH=3"
efax: 25:38 waiting 3.0 s
efax: 25:41 waiting 2.0 s
efax: 25:41 .280 [<CR><LF>OK<CR><LF>]
efax: 25:41 response "OK"
efax: 25:41 local 196lpi 14.4kbps 8.5"/215mm any 1D - - 0ms
efax: 25:41 remote 196lpi 14.4kbps 8.5"/215mm any 2D ECM-64 - 20/10ms
efax: 25:41 session 196lpi 14.4kbps 8.5"/215mm any 1D - - 10ms
efax: 25:41 command "+FTH=3"
efax: 25:41 waiting 3.1 s
efax: 25:42 .283 [<CR><LF>CONNECT<CR><LF>]
efax: 25:42 response "CONNECT"
efax: 25:42 sent TSI - caller ID
efax: 25:42 waiting 13.6 s
efax: 25:44 .034 [<CR><LF>CONNECT<CR><LF>]
efax: 25:44 response "CONNECT"
efax: 25:44 sent DCS - session format
efax: 25:44 waiting 13.6 s
efax: 25:44 .404 [<CR><LF>OK<CR><LF>]
efax: 25:44 response "OK"
efax: 25:44 command "+FTM=145"
efax: 25:44 waiting 3.1 s
efax: 25:44 .529 [<CR><LF>CONNECT<CR><LF>]
efax: 25:44 response "CONNECT"
efax: 25:44 Warning: termios.iflag is 000000005, not 000001005
efax: 25:44 Warning: terminal mode not set properly
efax: 25:44 waiting 30.0 s
efax: 25:47 .635 [<CR><LF>OK<CR><LF>]
efax: 25:47 response "OK"
efax: 25:47 sent TCF - channel check of 2700 bytes
efax: 25:47 command "+FRS=1"
efax: 25:47 waiting 3.0 s
efax: 25:47 .704 [<CR><LF>OK<CR><LF>]
efax: 25:47 response "OK"
efax: 25:47 command "+FRH=3"
efax: 25:47 waiting 3.0 s
efax: 25:50 waiting 2.0 s
efax: 25:50 .754 [<CR><LF>OK<CR><LF>]
efax: 25:50 response "OK"
efax: 25:50 Error: no command/response from remote
efax: 25:50 command "+FTH=3"
efax: 25:50 waiting 3.1 s
efax: 25:51 .757 [<CR><LF>CONNECT<CR><LF>]
efax: 25:51 response "CONNECT"
efax: 25:51 sent DCN - disconnect
efax: 25:51 waiting 13.6 s
efax: 25:52 .033 [<CR><LF>OK<CR><LF>]
efax: 25:52 response "OK"
efax: 25:52 command "H"
efax: 25:52 waiting 5.0 s
efax: 25:52 .259 [<CR><LF>OK<CR><LF>]
efax: 25:52 response "OK"
efax: 25:52 failed -> /Users/kmr/test-file.001
efax: 25:52 command "Q0V1"
efax: 25:52 waiting 2.0 s
efax: 25:52 .504 [<CR><LF>OK<CR><LF>]
efax: 25:52 response "OK"
efax: 25:52 command "H"
efax: 25:52 waiting 5.0 s
efax: 25:52 .655 [<CR><LF>OK<CR><LF>]
efax: 25:52 response "OK"
efax: 25:52 done, returning 3 (invalid modem response)
abcs-computer:~ root#
Thanks in Advance...

T.37 offramp fax not working

Hi,
I have implemented onramp and offramp for my customer. Onramp fax is working fine but the offramp fax is not working. When we test with facsBridge T37 we do not see fax coming on CME router.
Router configuration is
Model: 2911
IOS: 15.4(2)T
I have enabled the mta and foip debugs but no logs are generated. But when I run the wireshark debugs on laptop on which facsBridge application is running, I see acknowledgement from router. But Microsoft fax application which uses facsBridge as modem do the retransmission 2-3 times and then give fatal error.
I am not sure if issue is with config or i am hitting bug. Please guide me how to resolve this issue.

one update...on wireshark i am seeing RST, ACK from router which means it is reseting the session...but could not find reason for that. i tired with app_faxmail_offramp.2.0.1.1.tcl and app_faxmail_offramp.2.0.0.0.tcl script, but results are same.
Below is config of cme.
fax receive called-subscriber $d$
fax send transmitting-subscriber $s$
fax interface-type fax-mail
mta send subject Fax from On-Ramp GW
mta send with-subject $s$
mta send postmaster [email protected]
mta send mail-from hostname xxxxsolutions.com
mta send mail-from username info
mta receive aliases xxxxxsolutions.com
mta receive aliases smtp.gmail.com
mta receive aliases 10.1.30.13
mta receive generate mdn
mta receive generate permanent-error
application
service onramp flash:/its/app_faxmail_onramp.2.0.1.3.tcl
service offramp flash:/its/app_faxmail_offramp.2.0.1.1.tcl
service offramp1 flash:/its/app_faxmail_offramp.2.0.0.0.tcl
service fax_detect flash:/its/app_fax_detect.2.1.2.4.tcl
param redirect-number 106
param mode default-fax
dial-peer voice 7010 mmoip
service fax_on_vfc_onramp_app out-bound
max-conn 10
destination-pattern 4652746
information-type fax
session target mailto:[email protected]
incoming called-number 4652746
mdn
dsn success
dsn failure
dial-peer voice 7020 mmoip
service offramp1
max-conn 10
information-type fax
incoming called-number 9T
image encoding MH
image resolution standard
mdn
dsn success
dsn failure

HP LaserJet 1018 not printing landscape on index cards

I regularly print on 3 x 5 index cards with this printer. In fact, this is the reason I purchased the printer. Just this morning, I am suddenly unable to print landscape on it. Any file set up in landscape will run through the printer and come out blank. However, if I change the set up to print portrait, my prints are perfect. Hm...does anyone have any suggestions?

Hi. Did you ever figure out why you can't print 3x5 index cards in landscape mode on your HP printer? I'm having exactly the same problem. I can print the document on ordinary 8.5x11, but not on index cards. It was working a couple of weeks earlier. I've tried all the obvious solutions but so far nothing works. Thanks.

HP Officejet 6700 Fax not going through

When I try to send a fax, it dials but never connects?

Hi @Carlita61,
Welcome to the HP Forums!
I noticed that the fax is not going through with your HP Officejet 6700. I am happy to look into this for you!
What type of phone service do you have? Analog or digital? Analog. Digital. What’s the Difference?
If the phone service is analog, please see this guide, Cannot Send or Receive Faxes.
If the phone service is digital, please go to this guide, How to connect your HP Fax Device to an ISDN, ADSL, PBX, or VoIP line. Note: HP fax devices are designed to work with traditional analog phone services. They are not designed to work with digital phone services such as ADSL, PBX, ISDN, or VoIP. While HP fax products are not supported on these types of lines, they might work given appropriate setup and equipment.
To find out if your phone service is analog or digital please contact your phone provider.
Hope this information is helpful, and thank you for posting!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

External USB Modem fax not working under 10.5.8

I upgraded my Mac Mini home office server (print, fax, backup) to 10.5.8 and now it appears that faxing is completely broken (or maybe the USB modem driver.)
I've verified that this is broken on another system.
After booting, the following is seen in the fax log:
efax: 33:57 command "+FAR=1"
efax: 33:57 waiting 5.0 s
efax: 33:57 .956 [<CR><LF>ERROR<CR><LF>]
efax: 33:57 response "ERROR"
efax: 33:58 command "S0=1"
efax: 33:58 waiting 5.0 s
efax: 33:58 .157 [<CR><LF>OK<CR><LF>]
efax: 33:58 response "OK"
efax: 33:58 waiting for activity
efax: 33:59 activity detected
efax: 34:00 Error: tcsetattr on fd=5 failed: Invalid argument
efax: 34:00 Error: tcsetattr on fd=5 failed: Invalid argument
efax: 34:00 command "Q0V1"
efax: 34:00 Error: fax device write: Input/output error
efax: 34:00 waiting 2.0 s
efax: 34:00 waiting 2.0 s
efax: 34:00 command "Q0V1"
efax: 34:00 Error: fax device write: Input/output error
efax: 34:00 waiting 2.0 s
efax: 34:00 sync: dropping DTR
efax: 34:00 Error: tcsetattr on fd=5 failed: Invalid argument
efax: 34:00 Error: tcsetattr on fd=5 failed: Invalid argument
efax: 34:00 Error: tcsetattr on fd=5 failed: Invalid argument
efax: 34:00 waiting 2.0 s
efax: 34:00 command "Q0V1"
efax: 34:00 Error: fax device write: Input/output error
efax: 34:00 waiting 2.0 s
efax: 34:00 sync: sending escapes
efax: 34:00 Error: tcsetattr on fd=5 failed: Invalid argument
efax: 34:00 Error: fax device write: Input/output error
efax: 34:00 Error: fax device write: Input/output error
efax: 34:00 Error: tcsetattr on fd=5 failed: Invalid argument
efax: 34:00 Error: fax device write: Input/output error
efax: 34:00 Error: fax device write: Input/output error
efax: 34:02 Error: fax device write: Input/output error
efax: 34:02 waiting 2.0 s
efax: 34:02 command "Q0V1"
efax: 34:02 Error: fax device write: Input/output error
efax: 34:02 waiting 2.0 s
efax: 34:02 Error: sync: modem not responding
efax: 34:03 done, returning 2 (unrecoverable error)
Anybody else seeing this?

This solution is a "workaround" and will not affect in any problems, like I saw that they will happen after:
1.) Removing and changing "IOSerialFamily.kext" : ("The system extension '/System/Library/Extensions/IOSerialFamily.kext' was installed improperly and cannot be used....")
2.) or go back to OS 10.5.5... (latest security-updates not included)
Go to your System-Prefs -> Printing and Faxing
chose the Fax-Modem -> Options
1.) to receive faxes: choose "receive faxes on this computer"
2.) to send faxes: choose not to "receive faxes on this computer",
plug your modem out, wait 5 seconds and plug it in.
Now you can send faxes, but not receive,
before you choose "receive faxes on this computer" again.
To send, you have to start with 2.) again...
It's strange for a mac, but better than 10.5.5 or a corrupted system...
APPLE-STUFF: HERE AGAIN: FIX THAT FAX-PROBLEM FOR 10.5.8 QUICK PLEASE - IT'S IMPORTANT!!!
trollius

Cd jewel inserts not printing correctly-come out with only song name not artist and not in landscape form-hl

cd jewel inserts not printing correctly-only shows song title not artist and printing in portrait form where landscape form is required-pls help!

iTunes CD printing has been broken for several releases now. Some people have had success by directing the iTunes print output to a PDF file, and then printing the PDF.

Officejet 6600 fax not showing up in menu using windows 7 64

I using windows 7 64 I reinstalled hp software for Officejet 6600 all in one, but my faxing software will not show up in the menu . I have removed all drivers related to Officejet 6600 several times same problem every time . The fax menu was there before all hardware is still the same.

Hi G2123,
I understand you are no longer able to fax from your computer as the Officejet 6600 fax is not showing up. I suggest starting with the HP Print and Scan Doctor.
The HP Print and Scan Doctor is a free utility (tool) that helps to quickly resolve common printing, scanning and connectivity issues including but not limited to:
Connectivity :
USB: Verifies that the USB connection from your computer to the HP product is working correctly.
Network: Verifies that the network connection between your computer and your network is working correctly.
Device Status Test : Checks for device errors such as out of paper, paper jams, carriage stalls, and paper feed issues, and then provides instructions for fixing the error.
Driver Check : Checks for missing or corrupt driver files.
Device Manager : Checks for problems in Device Manager that would prevent printing.
Device Online : Checks if the product has been paused or set to offline, and then sets the status back to online if necessary.
Print Queue : Checks for and clears pending print jobs in the print queue (a log of print jobs waiting to print).
Port Match : Checks the port settings for the HP product.
Device Conflicts : Checks for conflicts with other drivers, such as other printer brands.
Ink Issues : Checks the cartridges and ink levels for issues that affect print quality.
Print Settings : Checks and adjusts the print quality settings.
Test Print : Prints a test page for print quality evaluation, and provides options for cleaning and aligning the printhead if necessary.
Scan Tests : Checks the scan mechanism, drivers, and registry entries.
You can also click the Printer menu to find the additional features such as cleaning printheads, aligning printheads, checking ink levels, and viewing advanced printer data for your selected printer.
Source: Try the HP Print and Scan Doctor for Windows
Click here to download and run the utility > HP Print and Scan Doctor
Please let me know if this resolves the issue, thanks.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Fax not answer

Dear Sir
I bought a Laser jet pro MFP M127fn from one week .
I do all the setup for reciving fax but it recive only when it standby and after energy saver start it type Auto off/Auto on
The fax didn't answer

Hi @Sunmoon0,
I see by your post that the printer isn't waking up to receive a fax. I can help you with this.
Make sure the printer is connected directly to a wall outlet. (don't use a power hub or a surge protector) This ensures the printer is receiving full power and may help this situation.
This information is provided from the manual on page 64. LASERJET PRO MFP.
Double check the settings on the printer.
Configure the Sleep/Auto Off After settings:
1. On the product control panel, press the Setup button.
2. Open the following menus:
System Setup
Energy Settings
Sleep/Auto Off After
3. Use the arrow keys to select the time for the Sleep/Auto Off delay, and then press the OK button.
NOTE: The default value is 15 Minutes.
4. The product automatically wakes when it receives jobs or when you press a button on the product
control panel. You can change which events cause the product to wake. Open the following menus:
System Setup
Energy Settings
Wake/Auto On Events
To turn off a wake event, select the event, and then select the No.
Go to setup, energy settings, wake/auto on events and select the fax.
This should bring the product out of sleep mode.
If the issue persists, update the printer's firmware.HP LaserJet Pro MFP M127fn Drivers. Select your operating system, click next, click the link for firmware.
What operating system are you using? How to Find the Windows Edition and Version on Your Computer.
How is the printer connected? (USB/Ethernet/Wireless)
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Fax not sent. Modem hangs up before transmission

I have been searching the forums and not found an answer to my problem
I have tried fax software from several different companies . All have had the exact same problem. I suspect the problem may lie in the modem itself
Every time I try to send a fax. I hear dial tone. I hear and see the unit on the receiving end pick up. I hear the recognition tones, and then my modem hangs up.
Which software I use or how I try to send the fax seems to make no difference.
I am connected to the internet vie Ethernet with a DSL modem on the same phone line
Please help

Hi DasColeman!
You cannot be connected to the Internet, while you are sending a FAX.
You must use a Dial-Up connection, to FAX.
Not all DSL Cable Modems can be configured to send a FAX using the Panther 10.3.x FAX function.
Review this KB Article Can I fax with my cable, ADSL, DSL, or ISDN modem using Mac OS X 10.3?.
I have DSL as well, and when I want to send or receive a FAX, I disconnect the Ethernet cable from the Mac Ethernet port, plug a wire from the wall jack to the Internal Modem port on the Mac.
I have a two port Splitter/Filter plugged into the wall jack.
The Cable/DSL Modem wire, is always plugged into one of the ports on that splitter.
When I want to use the FAX function, I plug the telephone wire into the other port, but I do not unplug the Cable /DSL Modem.
The Splitter/Filter may not be a necessity. If you don't have one, just unplug the Cable Modem wire from the wall jack, and plug in the telephone wire.
I then set the Network System Preferences, back to the Internel Modem, deselect the Built-in Ethernet, selecting Internal Modem, and dragging it to the top of the window.
This of course will disconnect the Mac from the DSL connection, and you can then use the Internal Modem to send or receive a FAX.
Also review this Topic Faxing, for additional tips.
Additionally, when you enter the recipient FAX number, use this format 1-area code-xxx-xxxx.
ali b

Fax not working when send and receive throguh PSTN

Fax failed when it is sent and received through PSTN. User are able to receive fax when sent and received using VoIP(onnet) but not through PSTN(offnet).

Hi bertley32,
Thanks for letting me know.
Try sending a fax to the HP Fax Back number: 1-888-473-2963, to see if you have the same results.
If you connect a phone to the printer, can you call out?
Update the printer's firmware. HP LaserJet Pro 200 color MFP M276nw Drivers.
Please check your private messages for additional steps to try.
In the forum beside your handle name just click on the envelope to view it.
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Bursting to fax not in landscape

Similar Messages

Maybe you are looking for