CME- Phone timing issue

All,
I have a CME setup with 20 IP phones. Though time zone , clock setting are corret in the router, all IP phones are showing wrong time in the display. Can any one help me to slove the problem.

Can you please share your CME config?
Sent from Cisco Technical Support iPhone App

Similar Messages

  • IPhone 6 and Bluetooth phone connectivity issues with my vehicle: this is how I fixed it.

    With so many threads on this topic, I wanted to detail the steps I took to fix my iPhone 6 Bluetooth issues regarding connectivity to my vehicle and handsfree calling.  My phone was pairing with my vehicle without a problem and syncing my contacts and call history but when I attempted to make a call (from either the phone or the vehicle screen) the audio went out and I could not hear the call either through the vehicle speakers or on the phone. The call was going through but I was unable to see it on my vehicle screen and/or hear it either the phone or the vehicle screen. 
    Based on my research and what I have learned so far, the people having problems are those who restored their new iPhone 6 from an iCloud backup from a previous phone, rather than setting up their iPhone 6 as a new phone.  I did an iCloud restore from my previous 5s running iOS 8.   
    First, I am a Verizon customer and I enabled Advanced Calling on my line.  After I requested that this feature be added to my line, under “Cellular” settings on my iPhone, I enabled LTE voice & data.
    Next steps:
    1) Unpair/remove iPhone from the vehicle;
    2) Forget/remove the vehicle from the phone Bluetooth settings;
    3) Soft reset the iPhone;
    4) Reset network settings on the iPhone; and
    5) Pair the phone to the vehicle again and attempt to make a call. 
    If that does not work…
    6) Perform a factory reset, erasing EVERYTHING from your phone and set it up as a new iPhone rather than restoring from a backup.  
    Resetting the network settings seems to be working for some people.  It did not work for me.  I tried it a few times with no result.  I did the dreaded factory reset, paired the phone with my vehicle and had all of my Bluetooth functionality back and was able to use the handsfree phone with zero issues.
    I was on the phone yesterday multiple times with Apple, Toyota Entune, Verizon and my Toyota dealer. Verizon blamed Toyota Entune, Toyota Entune blamed Verizon and my Toyota dealer blamed Apple.  Nobody had a clue how to fix this issue or what was causing it. I don’t know the exact reason why the previous iCloud backups are killing the Bluetooth connections, I just know what worked for me and I thought it was worth sharing. 
    Good luck.

    The new 8.0.2 update DID NOT FIX THIS ISSUE AT ALL. After you power off and on with the phone, same issue as the 8.0, all 3 of my cars lost Bluetooth connection and shows no signal at all.  Good job Apple, what a lousy update you guys did.
    2011 Lexus ES350
    2011 Subaru STI
    2012 Mercedes E350.

  • [svn:bz-trunk] 17102: Rewrite all ImageSnapShot tests to avoid any timing issue on various app server .

    Revision: 17102
    Revision: 17102
    Author:   [email protected]
    Date:     2010-07-28 11:48:20 -0700 (Wed, 28 Jul 2010)
    Log Message:
    Rewrite all ImageSnapShot tests to avoid any timing issue on various app server.
    Modified Paths:
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ImageS napshot/testCaptureBitmapData.mxml
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ImageS napshot/testCaptureImage.mxml
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ImageS napshot/testCaptureImageJPEG.mxml
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ImageS napshot/testCaptureImageScaleLimitedFalse.mxml
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ImageS napshot/testCaptureImageScaleLimitedFalseJPEG.mxml
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ImageS napshot/testCaptureImageScaleLimitedTrue.mxml
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ImageS napshot/testCaptureImageScaleLimitedTrueJPEG.mxml
        blazeds/trunk/qa/apps/qa-regress/testsuites/mxunit/tests/remotingService/dataTypes/ImageS napshot/testEncodeImageAsBase64.mxml

    I am modifying the correct httpd.conf file on the server, it just doesn't seem to work. - If I put the rewrite rules in the <Directory /> the rewrite works but it adds /Library/WebServer/Documents to the URL.
    I also tried putting the rewrite rules in <IfModule mod_rewrite.c> but that did not work either.
    mod_rewrite is enabled and running on the server.
    I will post the rewrite rules again in the code brackets. Sorry for the long post. - If some one can try them out on their Leopard Server to see if they can get them to work, it would be much appreciated. Again, these work on my Leopard Client but I can't get them to work on Server.
    -- The httpd.conf file posted above is just the default conf file found in /private/etc/apache2/
    <code>
    RewriteEngine On
    Options +FollowSymLinks
    RewriteRule ^(.+)/$ http://%{HTTP_HOST}$1 [R=301, L]
    RewriteCond %{THE_REQUEST} ^GET\ ([^\?]+)\.php(.*)\ HTTP
    RewriteRule (.+)\.php(.*)$ $1$2 [R, L]]
    RewriteCond %{THE_REQUEST} ^GET\ ([^\?]+)\.asp(.*)\ HTTP
    RewriteRule (.+)\.asp(.*)$ $1$2 [R, L]]
    RewriteCond %{THE_REQUEST} ^GET\ ([^\?]+)\.aspx(.*)\ HTTP
    RewriteRule (.+)\.aspx(.*)$ $1$2 [R, L]]
    RewriteCond %{THE_REQUEST} ^GET\ ([^\?]+)\.htm.(.)\ HTTP
    RewriteRule (.+)\.htm.(.)$ $1$2 [R, L]]
    RewriteCond %{THE_REQUEST} ^GET\ ([^\?]+)\.cfm(.*)\ HTTP
    RewriteRule (.+)\.cfm(.*)$ $1$2 [R, L]]
    RewriteCond %{THE_REQUEST} ^GET\ ([^\?]+)\.bak(.*)\ HTTP
    RewriteRule (.+)\.bak(.*)$ $1$2 [R, L]]
    RewriteCond %{THE_REQUEST} ^GET\ ([^\?]+)\.inc(.*)\ HTTP
    RewriteRule (.+)\.inc(.*)$ $1$2 [R, L]]
    RewriteCond %{THE_REQUEST} ^GET\ ([^\?]+)\..(.)\ HTTP
    RewriteRule (.+)\..(.)$ $1$2 [R, L]]
    <code>

  • Phone Connectivity Issues

    While I love the iPhone, I've been having some problems with the actual phone portion of this little device.
    I drop 2 - 3 calls a day (in areas that AT&T states there is coverage).
    Callers complain of an echo problem on their end which I can also hear on my end at times.
    I loose service at times which causes me to put the phone into airplane mode and back or even power it off to restore.
    Has anybody else had similiar problems. Wondering if I need to make another trip to the apple store for support.

    The new 8.0.2 update DID NOT FIX THIS ISSUE AT ALL. After you power off and on with the phone, same issue as the 8.0, all 3 of my cars lost Bluetooth connection and shows no signal at all.  Good job Apple, what a lousy update you guys did.
    2011 Lexus ES350
    2011 Subaru STI
    2012 Mercedes E350.

  • How to fix the Timing issue in Discoverer reports

    Hi,
    While running the discoverer report in Discoverer plus is taking more than 1 hour to complete( Gen.time + Extract to excel)
    where as the same report completes quickly in discoverer desktop.
    how to fix the timing issue in discoverer plus 
    Thanks
    Srinivas

    Timo Hahn wrote:
    There is a problem with autoHeightRows and columnStretching used together in 11gR1.
    Have you tried without columnStretching?
    Or have you tried if it works in 11gr2?
    TimoHi Timo, Thank you very much for taking time to respond to my question.. :)
    Back to my question...
    I tried removing the columnStretching although my requirement really requires this but no effect really happens even if I remove this.
    Based on my investigation on the generated HTML, I notice the following items:
    1. A table is being wrapped in a div that is being set at a fixed height.
    2. On first load, if your autoheight rows is set to 6, the framework is setting a height of 96px to the div. This height would almost cut the last row of the table.
    3. If you try to refresh the page or try to re-PPR the component, the framework resets it to 102px which causes the last row to be fully displayed.
    My only concern is that IE is perfectly displaying this while Chrome and FF are having problem.
    Based on my understanding, the framework is messing up the height only on first load. Not sure but this is how I see it. I am really not confident also on my findings
    and I would most likely hear other's comment.
    Thanks.

  • [svn] 4859: -Fix packaging timing issue that was caused by the rebuilding of the air applicationupdater .

    Revision: 4859
    Author: [email protected]
    Date: 2009-02-05 10:15:22 -0800 (Thu, 05 Feb 2009)
    Log Message:
    -Fix packaging timing issue that was caused by the rebuilding of the air applicationupdater. The recompiled files would get laid down properly only to have the old files put back down on top of them. I also made sure the build directory was removed after updateAIR ran so it would not be included in the package
    -removed bundles.properties from the wireframe project
    bug:SDK-19128
    qa:yes
    doc:no
    checkintests:pass
    Ticket Links:
    http://bugs.adobe.com/jira/browse/SDK-19128
    Modified Paths:
    flex/sdk/branches/i10/build.xml
    flex/sdk/branches/i10/frameworks/build.xml
    Removed Paths:
    flex/sdk/branches/i10/frameworks/projects/wireframe/bundles.properties

    Hi Chris,
    I have confirmed this is an AIR SDK 13.0.0.83 bug.
    I have reported this bug to Adobe Bugbase, and I also included the workaround:
    https://bugbase.adobe.com/index.cfm?event=bug&id=3750892
    The workaround is:
    Simply comment the <externalSwfs> tag in your -app.xml will solve this bug, like this: <!-- <externalSwfs></externalSwfs> -->
    DarkStone
    2014-04-28

  • VISA Read timing issues

    I am using an RS232 to control an older model Power Supply (OXFORD PS 120-10).
    I have successfully written several VI's that all work, the only problem is that VISA Read takes WAY too long. I'm talking 10's of seconds to refresh. I need it have it refreshing in milliseconds or at least tens of seconds for the measurements we need. All of the VI's I have written have the same timing issue. 
    Attached is the most basic Serial Read/Write VI. Is there any way to improve the Read rate? Or might this just be an instrumentation issue. The strange thing is the Write commands work almost instantaneously (I can seem them on the instruments display).
    Please help if you can, I've only been working with LabVIEW for a few weeks and am very must still in the learning process. 
    Thanks!
    Solved!
    Go to Solution.
    Attachments:
    READandWRITE timing test.vi ‏14 KB
    READandWRITE timing test.vi ‏14 KB

    Do you have the communications protocol for the power supply? If you do not have everything right, you will have problems with communications.
    Tens of seconds is a clue that you may be getting timeout errors because the default timeout is 10 seconds. Try placing an inidicator on the error out wire inside the loop (after Read) to see if an error occurs on any iteration. The way you have the VI set up you only see the error on the last iteration of the loop.
    You are writing a carriage return to the instrument. If it requires that, it almost certainly sends a carriage return with the response. (This is why I asked about the protocol). If the instrument sends a carriage return (or other termination character), then you should Enable Termination Character on the Configuration VI and set the termination character to the correct value. The default is line feed (hex A or decimal 10). A carriage return is hex D or decimal 13. You must wire the numeric value to the termination character input for any value other than the default. Then change the byte count value (at the Read input) to a number larger than the longest message the instrument will ever send, perhaps 100 or 500. The Read will end as soon as the termination character is received, regardless of the number of characters.
    I suspect that this is the problem - the instrument sends fewer than 10 characters in most messages but does send a termination character.
    Lynn

  • Frustrating Phone Upgrade issue

    We need help with phone upgrade issue we encounter when BestBuy associate process our upgrade. Associate is saying we are not eligible but we have not done any phone upgrade since Jan 2011. Our ATT mobile service was established with BB in 2009 and we only upgraded 2 phones in Jan 2011 thru BB. The only recent change in January 2013 was a change of responsibility between my spouse and me since my company has a better employer discount thru ATT. No change and per ATT, no contract and we should be able to upgrade in any retail store. But BB keeps telling us we have issue with ATT and can do our upgrade only with ATT Corporate Store. Our mobile account is a regular family plan account as originally established with BB and just like any BB customer, have employer's discount attached. I don't understand how BB system communicates with ATT system so it is hard for me to explain to ATT what "error message" BB associate is receiving. It has become so frustrating with BestBuy telling us to check with ATT and then for ATT to tell us that there is no issue at their end. We have been a loyal BB customer with all major appliances bought from them including protection plan. The least they can do is work with their ATT representative to figure out between themselves what the issue is. Here we are willing to give both companies our business with new phones and new contracts and no one can help us out.

    LTGee -
    I am very sorry to hear about this. I am going to send you a Private Message to collect some information from you to see if we can get to the bottom of this. To check your private messages, ensure you are logged into the forum and click on the envelope on the upper right hand side of the forum.
    Thanks!
    Jesus|Senior Social Media Specialist | Best Buy® Corporate
     Private Message

  • C3120 trunk timing issue on HP B460G1 ?

    hello
    customer encoured issue of trunking timing issue between
    C3120 and HP blade server, unable to get ip from DHCP
    server when server is booting up
    seems issue resolved in .53SE but i didnt  find either
    on CCO or HP Web ?
    any advice welcomed
    JYP

    Did you put the trunk in portfast mode ?
    regards,
    Geert

  • Questions about phase difference (possible timing issue) RC circuit

    Hello,
    Below is the program I am using to measure the phase difference in an RC circuit. Simply put I generate a 2kHz sine wave in LabView and send it to the circuit using an Analog output. Then I measure the output sine wave using an analog output.I also measure this using n oscilliscope. I cna clearly measure the phase difference with the oscilliscope and know it to be approximately 1.4 radians.
    Issues with the program:
    Different phase difference measured each time the program is run for the circuit. It is also never correct.
    Possible causes:
    You will notice by looking at the vi I measure the phase from the signal generator. Should I be using a second analog input to measure the sine wave as it is outputted at the start of the circuit?
    I mainly think that it is a timing issue. While the phase difference is constant each time the program it varies each on run. So the time each tone measurement begins its first measurement seems to be different each time and causes this different phase reading.
    The card I am using is a PCI 6221, is there a timing issue related from switching to input and output acquistion or are they seperate.
    Is there anyway to ensure that both tone measurements are measuring phase at the same point in (actual) time?
    I would really appreciate any advice or alterations on the program anyone could offer me (I am a college student and LabVIEW is not on our curriculum so I have no support, yet I am using it for my project (D'oh!))
    Solved!
    Go to Solution.
    Attachments:
    RC Circuit Test.vi ‏271 KB

    I would certainly acquire two signals.  Feed the analog output right back into an analog input and then your filtered signals in another.
    Initially, I would feed the analog output into both analog inputs and measure the phase delay due to the multiplexed A/D on the card.  Once you have that measurement, you can feed in the filtered signal and then measure the phase difference of that signal.
    Randall Pursley

  • Unity Express voice mail timing issue.

    Hi,
    I have installed one uc520 at one of our customer. i configured voice mail but there is one issue with the voice mail timing. Suppose i retrive the voice mail the voice mail prompt is giving the wrong time. Suppose I send a voice mail to a subscriber at 3pm, the voice mail prompt is saying 'message send at 4 pm'.
    I checked both cme and cue clock settings and both are showing the correct time.
    Can anybody help me on this issue
    Regards
    Thejas

    Are the calls to CUE getting dropped when you dial from an IP Phone at site 1 (callmanager) ?
    How is the CME router setup in Callmanager ? Is it added as a regular H323 gateway or a H225 trunk ? Either ways, make sure the gateway registers with the correct IP that is used in Callmanager.
    So if CME has a wan ip (a.a.a.a) and a lan ip (b.b.b.b), if you add b.b.b.b as the CME gateway's ip address in Callmanager, then you need to bind the H323 ip address as follows.
    interface fa0/0
    ip add b.b.b.b
    h323-gateway voip bind srcaddr b.b.b.b
    Most likely the CME gateway is sending calls to Callmanager using ip address a.a.a.a which is the wan ip, through which it has the default route to Callmanager.
    Hope that makes sense!

  • CME 8.6 Issue

    ! Last configuration change at 16:28:19 GMT Mon Feb 27 2012 by admin
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname CCME2811
    boot-start-marker
    boot-end-marker
    logging buffered 1000000
    no logging console
    enable secret 5 $1$UQ7v$Qe5DTyBYYB20KoEqCFqy30
    no aaa new-model
    clock timezone GMT -6 0
    clock summer-time GMT recurring
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 10.10.1.1 10.10.1.20
    ip dhcp pool phone
    network 10.10.1.0 255.255.255.0
    default-router 10.10.1.1
    option 150 ip 10.10.1.1
    no ipv6 cef
    multilink bundle-name authenticated
    stcapp ccm-group 1
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    no supplementary-service sip refer
    h323
    sip
      registrar server expires max 3600 min 3600
    voice class codec 1
    codec preference 1 g711ulaw
    voice class custom-cptone jointone
    dualtone conference
      frequency 600 900
      cadence 300 150 300 100 300 50
    voice class custom-cptone leavetone
    dualtone conference
      frequency 400 800
      cadence 400 50 200 50 200 50
    voice translation-rule 1
    voice translation-rule 9
    rule 1 /^911$/ /911/
    rule 2 /^8\(.*\)/ /\1/
    voice translation-rule 10
    rule 1 /\(34..\)/ /605274\1/
    rule 2 /\(41..\)/ /605275\1/
    voice translation-profile CALLER_ID_TRANSLATION_PROFILE
    translate calling 1
    voice translation-profile PSTN-LD
    translate calling 10
    voice-card 0
    dsp services dspfarm
    crypto pki token default removal timeout 0
    license udi pid CISCO2811 sn FTX1017A0Z1
    archive
    log config
      hidekeys
    username admin privilege 15 secret 5 $1$Casc$PqFn0/a.oZmvNJdhQAieS.
    username conference password 0 null
    username open password 0 null
    class-map match-all L3-to-L2_VoIP-Cntrl
    match ip dscp af31
    class-map match-all L3-to-L2_VoIP-RTP
    match ip dscp ef
    class-map match-all SIP
    match protocol sip
    class-map match-all RTP
    match protocol rtp
    policy-map EthOut
    class RTP
    policy-map output-L3-to-L2
    class L3-to-L2_VoIP-RTP
      set cos 5
    class L3-to-L2_VoIP-Cntrl
      set cos 3
    interface Loopback0
    ip address 10.1.10.2 255.255.255.0
    interface FastEthernet0/0
    description ** Voice VLAN **
    ip address 10.10.1.1 255.255.255.0
    duplex auto
    speed auto
    interface FastEthernet0/1
    description ** Data VLAN **
    ip address 192.168.100.2 255.255.255.0
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    no ip http secure-server
    ip http path flash:/gui
    ip route 0.0.0.0 0.0.0.0 192.168.100.1
    telephony-service
    sdspfarm conference mute-on 111 mute-off 222
    sdspfarm units 1
    sdspfarm tag 1 confdsp1
    conference hardware
    authentication credential (hidden info)
    em logout 0:0 0:0 0:0
    max-ephones 36
    max-dn 108
    ip source-address 10.10.1.1 port 2000
    caller-id block code *10
    no caller-id name-only
    calling-number initiator
    service phone videoCapability 1
    system message IT Outlet
    url services http://10.1.10.1/voiceview/common/login.do
    url authentication http://10.1.10.2/CCMCIP/authenticate.asp
    cnf-file perphone
    load 7914 S00105000300
    load 7935 P00503021500
    load 7960-7940 P00308000500
    time-zone 8
    voicemail 5000
    max-conferences 8 gain -6
    call-forward pattern .T
    call-forward system redirecting-expanded
    moh music-on-hold.au
    web admin system name admin secret 5 $1$vp1x$4PuEyYU1BsGN.KzjhnVOR.
    dn-webedit
    time-webedit
    transfer-system full-consult
    transfer-pattern 8.T
    secondary-dialtone 8
    after-hours pstn-prefix 4 4
    night-service code *1234
    night-service weekday 18:30 07:00
    night-service day Sun 00:00 23:59
    night-service day Sat 00:00 23:59
    This is my running config that I have so far.  The issue I'm having is that I can't access the web interface to do any configuring.  I am currently hooked up to a DMZ which is on a 192.168.100.1 ip scheme.  I am just doing testing of this phone system before I put it in our business to run 100%.  At the moment the only thing holding me back is the web interface my boss wants me to be able to access the web interface so then I can configure clients easier.  The farthest I've gotten was at 10.10.1.1 I got a page that loads that asks me for my username and password and then it says something about QoS Device Manager - Configure and monitor QoS through the web interface.  When I click on that it takes me to a 404 error page.  I've looked over my IPs as I posted above multiple times to try and figure out what I'm doing wrong.  I at first was having DHCP issues with my laptop and the switch the router was hooked up to, but I got that figured out.  Then I thought it might have been vlans but when I did a show vlan-switch I noticed there were only 1 - type = enet, 1002 - type = fddi, 1003 - type = tr, 1004 - type = fdnet, and 1005 - type =  trnet.
    I noticed I posted this in the wrong area from before.  To update what I've done from then till now.  All the CME files have been loaded into flash like I was reading in other posts.  I did a show flash and everything seems to be in there that I need.  I determined the page that is loading up after I type 10.10.1.1 or 192.168.100.2 in my web browser is the router itself.  I have this hooked up to a DMZ like I said before and it keeps giving my laptop 2 default gateways one being 0.0.0.0 and the other being 10.10.1.1, not sure why it's doing that.  My laptop is receiving and 10.10.1.21 address from the router and I have the router hooked up to the DMZ under 192.168.100.2.  We were having issues with an older version of CME so I upgraded to 8.6, I'm using a test router to make sure everything is working before I implement it into our real phone system.  Still can't get a web interface to show up.  I don't think my ip route command is right but that's how it was in the old config from the phone system we have now.  I did a backup of that config and editted everything based off the backup config.  Somewhere I think in my config I believe I have something wrong pertaining to an IP address but I can't see it.  Been working on this all day and haven't gotten anywhere.

    Hi Jamie,
    Please use the below link,
    https://supportforums.cisco.com/docs/DOC-8172
    Hope it helps,
    Anand

  • Geek Squad phone insurance issues

    I am having a terrible time with the Geek squad insurance that I pourchased with my phone almost two years ago. I loved my I phone 4s that I bought and didnt have any trouble with it until it froze during an update about a month and half ago. My complaint or issue here is first of all I was under the impresion that when I purchased the insurance they would be replacing my ophone new one not a referbished one. In fact im all but certian of it because my son worked there and he told me they were getting ready to change it so I needed to be sure mine was not changed. anyway that was over a year ago and i had no problems then until now, i go in they give me a refurbished phone, i dont argue at the time but I was dissapointed as this was not what I have been paying for for almost two years now. That phone then overheats and stays on overheat for over an hour at 8:30 in the morning and its not hot outside or any reason for this. So i go back not happy and get told this time we will give you a white glove phone.... WTH either your phones are good enough to be sent back out or they ar not that was bull crap from the minute they said it. But I own a business two actually and i cant run them without a phone so I get another loaner phone and wait for my white glove phone. i get it ive had it about a week and it went (removed per forum guidelines) on me day before yesterday. I mean the home button stopped working it started calling people and factimeing my clients in other states randomly taking pictures and turning my music one. at thr time it was happening My husband was locked out of house that he needed to get into to clean i had the client calling but couldnt answer my phone and messages for texting wasnt working either so I could not communicate with either of them. We had only this time frame to get the job done as the power was only for a short time so I potentially had a client that would no longer be using us because of this situation. So anyway I get to the counter and get told that they weill send me yet another refurbished white glove phone but this time someone from corprate will call me to check on the phone. please really, a call does not make the phone be working properly and odes not fix the reallu upset  client i have on my hands. I dont understand at all how the white glove phone i got had more problems combined than all the others. I dont understand how they are not backing the warranty i know i have ( looking for my copy still though) that says its a new phone i should be getting in the first place not three refurbished phones in a month.Our other business is sales online and i do not take orders over the phone only the website or text e mail , something that i can refer back to incase they have an issue and feel they arent getting what they ordered, every time i lose a phone i lose my grounds to prove what someone ordered if they have a complaint. This could potentially cost me 400$ every time, thankfully that has not happened yet. I called corperate and was told to go into the store again and speak to the manager. that the lady would put in a claim but that didnot mean the manager would actually call me. what the hell! This white glove thing is really makingme upset too, we clean carpets for a living and if we go out and just use cold water and no chemicals etc and say here you go we are done and then when a customer complains about it we say oh ok well this time i will use hot water and chemical and do it right how would that work , it doesnt that is not ok an any level and obviousely i am very upset I know that my grammer and spelling are crazy right now im just so upset. Oh thats the other thing I was told if they did give me a new phone after this next refurbished one doesnt work then they will give me a new phone but it will be my upgrade for my verizon account. how does that work NO! i am out of contract on all 5 phones we have with verizon and do not want to be in it again and them fullfilling the replacement for insurance purposes should have absolutely nothing to do with my verizon account they are not linked in any way and that is not acceptable. My last concern here is that the warranty that i have paid on for two years now is up on NOV 8th, I was told to make sure that the refurbished phobe i had was working perfectly at that time because once the warranty is up its up. how is that ok i have paid this for two years anf they cannot get me a proper working phone before the warranty expires so im out of luck aftertwo years i end up with a non working phone possible. NO just NO i am so unhappy.I do intend to make some calls because insurance has to be handled in a certian way and this is not it. I do intend to report them ! 

    Hello MTRBLE,
    As my phone is on me at all times and is seemingly attached to my hip, I understand how disappointing it is to find your phone not working. It sounds like you’ve had your fair share of non-working phones, and I’m sorry for the frustration this has caused. When purchased, our Geek Squad Protection   (GSP) plans are put in place to help circumstances like yours in an efficient, timely manner. There seems to be some residual confusion regarding our plans though, as it’s a very rare occurrence to receive a new phone from service.
    With phones under our GSP plan, our current repair process is called Rapid Exchange. If you have a damaged or non-working phone, it should be sent out to service via a local store. To save our customers valuable time, a service order is simultaneously created from our service provider to ship out an already repaired phone. These phones go through a rigorous refurbishment process to make sure that a customer receives a phone meeting its manufacturer’s standards. However, the past experiences you describe haven’t gone as smoothly as we would've liked, as it sounds like we missed the mark with your past repair orders.
    I would like to be able to see if I may help in this situation. I'm unable to find your recent service orders underneath the email address associated with your forum account though, so I would need additional information from you to see if I can locate them.  Please know that I’ve send you a private message to gather that information. You may view your messages by logging into the forum and clicking on the envelope in the upper right-hand corner of your screen.
    Thank you for posting,
    Alex|Social Media Specialist | Best Buy® Corporate
     Private Message

  • Iphone 4s phone call issues

    I just bought an iphone4s, white, 32gb. Sometimes when I make a phone call the person that I am ringing cannot hear me but I can hear them. I have to turn the phone off and then on again, then call them before they can hear me.  I dont have the phone in a cover as yet. Is anyone else having the same problem and is there a solution?

    brconflict1 wrote:
    Since the latest updates to iOS, I'm hearding more issues reported to my company where iPhone users are not able to be routed correctly in our IVR. From the PBX, I'm seeing such as the following example: Callers dialing an extension 312, for example are able to dial 31, but the 2 is not responding on the iPhone. When the caller does eventually get the 2 to go through, the PBX states 31 is an invalid extension, and then registeres the 2 as a new entry, which is our Sales Queue option. I have confirmed this on my iPhone 4S.
    Dialing in the main keypas dialer on the iPhone is fine. However, the additional, smaller keypad for IVR nagivation use is not.
    IF the keypad is fine on the iphone, but not smaller keyboard whatever that is, what makes it an iphone/Apple or software issue.

  • IPhone 4 Phone Call Issues

    About a week ago I noticed my iphone 4 (updated IOS) was having issues with phone calls.  I would make a call to someone and mid-call they could no longer hear me.  In other cases, I made a call to someone and they never could hear me at all.  Other cases, someone calls me and they cannot hear me.  Finally ther are cases where I call someone and mid-call there is a bunch of static and they cannot hear me.
    I spoke with Apple and they told me that I needed to restore the phone and install it as a new iPhone.  This should deal with the issue.  I did such steps and then synced the phone and tried to make a call.  The first three calls nobody could hear me.  The next call they could hear me for 2 minutes and then static and nothing.
    I have had a new SIM card installed and have reset the network as well.  In reading the Apple Support Community postings, it looks like the only long term solution is to acquire a new phone.  Is there any other solution anyone knows of to help remedy this situation.  I have had the iPhone 4 for 2 years without an issue and in the last week, this crops up.  It has not been in water, it has a case on it, I am not covering up the mics, the speaker phone is off. 
    Next to getting a new phone, any ideas?

    There is nothing to sort out.
    Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new).  Try each of these in order until the issue is resolved.
    If the issue still occurs, take the device to Apple for evaluation as there is obviously a hardware issue.

Maybe you are looking for