Gone ACL brain-dead

I need to create an ACL that will allow in & outbound traffic between 10.34.44.62-126 and 10.35.44.192-254.
this ACL is going in a 3750.
Any ideas?

Something like this, break the ip's into subnets so you don't have too many ace's. So that would be...
10.34.44.62
10.34.44.63
10.34.44.64/26
and
10.35.44.192/25
access-list 100 permit ip host 10.34.44.62 10.35.44.192 0.0.0.127
access-list 100 permit ip host 10.34.44.63 10.35.44.192 0.0.0.127
access-list 100 permit ip 10.34.44.64 0.0.0.63 10.35.44.192 0.0.0.127
access-list 101 permit ip 10.35.44.192 0.0.0.127 host 10.34.44.62
access-list 101 permit ip 10.35.44.192 0.0.0.127 host 10.34.44.63
access-list 101 permit ip 10.35.44.192 0.0.0.127 10.34.44.64 0.0.0.63
int vlan 34
ip access-group 100 in
int vlan 35
ip access-group 101 in
I don't know what your vlans are but that should give you a good idea.

Similar Messages

WRT54G goes brain dead

First of all, the problem I am seeing occurs on an older version of firmware (not sure which one) and the latest (1.02). Also, I tried this on another WRT54G, with the same result. 2 different routers, and 2 different firmwares.
My ISP (a wireless network, but the output of the modem is a standard Ethernet cable which plugs into the WAN port of the router), seems to reset their tower overnight most nights. Bottom line is my ISP connection is down for some time (minutes probably). The WRT54G goes belly up aftwards. It "thinks" it's connected (the lights all flash correctly, and the status tab in the admin console says it's connected), but there is no access: no browser, no VOIP, no pinging. I can reset the router by pulling the plug or doing a disconnect/connect sequence on the status tab, and all is well again. I have verified this belly-up condition manually: I can disconnect the WAN ethernet connection for a few minutes, and then connect it back, and the WRT54G has gone brain dead: no connection.
I have configured the WRT54G manually, and using their installation wizard. Like I said, 2 different routers, 2 different firmwares (including the latest one).
I borrowed a Motorola WR850G. Guess what? It works! If you disconnect the WAN and reconnect, it just starts working again, no reboot necessary. So, what is going on with the WRT54G? Surely this is such a basic issue (recovering from WAN-side lost connectivity), that I can hardly believe this product can't protect itself from this issue. Help!

You may want to check for PPOe and also make sure that your router is configured with the correct TZ and DST settings. Some ISPs use domain controllers that are very time sensitive. And since DST has changed, you may be running into this problem with your linksys devices.
Good luck.

Anyone else notice how brain dead Siri is lately?

What is going on with Siri lately?
She seems completely brain dead.
Completely unable to find a location she just found less than a month ago. Nary a whimper of a hint.
I ask for directions to one city from another city and she gives me places of interest in the target ciy.
What is going on???

Hello Will Starck1,
Thanks for the question. After reviewing your post, it sounds like Siri is not able to understand you. I would recommend that you read this article, it may be able to help the issue.
Get help with Siri - Apple Support
Thanks for using Apple Support Communities.
Have a nice day,
Mario

Ilife install is brain dead

I imported an Iphoto library from someone who had a more recent version of iphoto that I had. I got an error saying I needed to install the newer iphoto. No problem I've been thinking about upgrading anyway. I install ilife 2008 which runs fine. I notice it is installing itunes even though I already have 8.02 installed. When I start itunes it says it is corrupted an I need to re-install from scratch. I download itunes and reinstall. This works and there is no music loss. Here is the question.
Why can't the ilife install use common sense when installing and at least ask if you intend to load an older version. It should give you the option of leaving it alone. Today's option of corrupting the existing 8.02 version is brain dead.

I just went through the same exact thing!! It was pretty frustrating!

Brain Dead iPod

I have a problem similar to Steve's. Mine is easily recreatable. When listening to an audiobook (.m4b) file. Hit pause, then menu to top menu, and select SLEEP. Ipod turns off, and will not restart unless the hold / select / menu procedure is used. Happens every time. If I go and listen to and MP3 file, and then sleep, it seems to work normally. Any ideas what I am doing wrong?
I try to shutdown by listening to a song, but sometimes I set pause on an audiobook, and it times itself out to sleep... unfortunately it's brain dead after that.

hi CoMpX!
... we can't possibly let your dad go on thinking dark thoughts ...
first check to see if you've got a fast user switching issue:
http://docs.info.apple.com/article.html?artnum=93764
... but if that isn't it, try:
(1) do a
b repair install
(it tends to fix precisely this problem). Go to your add/remove programs, select itunes, click "change/remove",
b but
this time select "repair".
... and if that does work:
(2) try this tip:
Scott Patrie, "iTP: The software required for communicating with.", 11:38pm Oct 8, 2004 CDT
... and if that doesn't work:
(3) try a
b clean uninstall
prior to reinstalling:
Da Gopha, "iTfW: stepwise clean uninstallation of iTunes", 09:51am Apr 5, 2005 CDT
post back to let us know if you got any joy.
love, b

It's not that the Flash plugin has crashed, it's that Firefox will not play the code written - IE9 does, Chrome does, Safari does - what's up with your Flash support - it's been brain dead for the last three releases - ever since v4 I think

Enter this url in any modern browser IE9 (I never would have believed that I would be complaining about Firfox not working and IE does! - it that how far you've gone down?), Chrome (no wonder people are switching to it in droves) and even Safari - and it plays, but not in Firefox v6.02 - it used to play fine when I first uploaded it back in July 2010 (v3.6 Firefox I think)
http://www.burleighphoto.com/1007-pmb-slims/04/index.html
http://www.burleighphoto.com/1106-chris-sharyl/01/index.html
Try this link in Firefox v6 and then try it in Chrome - nuf said.
Hope you can fix this or I'll be having a big disclaimer on all of my site - does not work in Firefox. Never thought I would be saying this.
Thanks. Craig.

I should test it on my wife's old Xp with v3.6 - too late tonight - will check tomorrow. Thanks for your help. Craig.

Mail & iChat gone all white & dead

Something really strange just happened: The Mail Appl. window went all white, I just see the folders on the left, but all mails are invisible. I checked the option "show mailboxes" under View, but that one was activated. The folders ell me that mails are in fact arriving, it's just that I can't see them.
To complete the fun, iChat stopped working as well.
Thee must be something broken "under the hood" but I'm not much of a mac-hanic. Are you? Thanks !
iMac 20 Intel Mac OS X (10.4.9)
iMac 20 Intel Mac OS X (10.4.9)

Normally, in the mail application window, the left column shows the folders, mailboxes etc. The major part of the window shows the mails themselves and that is what I don't see at all no more. It's all just white. No Mail to see. When I use my iBook all is fine. So it's not the account thats wrong.
I guess the mistake is somewhere deeper hidden in the OS because iChat doesn't work either.

Brain dead on adding a simple text rollover...

Hi there -
As my title indicates, I'm having an issue. Captivate 8. I have an interface with a set of graphic buttons, and a hidden set of labels associated with the slides. Clicking a button goes to that topic's slide. I want to use an old-fashioned rollover event to show the caption which then disappears on rollout. I'm working in a responsive project. Optimally (and historically) I'd just use the caption in association with the button's rollover state. However, I can't see how to do that in Captivate 8.

Hello,
Responsive design is for HTML5 output only. Rollovers are not supported for HTML5, AFAIK. How do you do a rollover on a smartphone? You can check the HTML5 Tracker (Project menu), that will tell you which objects are not supported (was also the case in previous versions).
Hint/Success/Failure captions are not on rollover, sorry.
Lilybiri

2 stupid question - for Brain Dead iPad user

Tried to register iPad AppleCare Protection Plan on-line. Couldn't find registration number inside the box, only 2 pamphlets on getting started. Tried using the numbers on the sticker on outside of box but they didn't work either....Help?
Lastly, I purchased Breaking Bad season 1 in HD, downloaded and viewed all episodes. Tried to do same for season 2 and got error message I don't have enough space to dowload. Checked settings and showing 22 GB free. Ideas? Thank you!

Generally when you purchase AppleCare at the same time as the covered product, the plan is registered automatically and there's nothing you need to go. You can enter in your iPad's serial number and check the coverage here:
https://selfsolve.apple.com/agreementWarrantyDynamic.do
though if you just bought the iPad, it may take a couple of weeks before it appears in the database due to the very high load during the holiday season.
I'm not sure about the capacity issue. You might try restarting your iPad (hold down the power and home button until you get the red "swipe to turn off" screen) and see if that makes a difference.
Regards.

Brain-Dead iPod shuffle!

I'm on my dad's PC right now, and there is something wrong with his iPs. When I plug it in, it just mounts in My Computer as F:, and it was NOT set up to enable disk use. So I opened iTunes, and it comes up saying: "The software required for communicating with the iPod is not installed correctly. Please reinstall iTunes to install the iPod's software." so, I did that, rebooted, and his iPod still won't work. So, I tried to go to the iPod Updater, but it just said "iPod service error." I clicked OK, and the updater closed. I don't know what to do, please help!

hi CoMpX!
... we can't possibly let your dad go on thinking dark thoughts ...
first check to see if you've got a fast user switching issue:
http://docs.info.apple.com/article.html?artnum=93764
... but if that isn't it, try:
(1) do a
b repair install
(it tends to fix precisely this problem). Go to your add/remove programs, select itunes, click "change/remove",
b but
this time select "repair".
... and if that does work:
(2) try this tip:
Scott Patrie, "iTP: The software required for communicating with.", 11:38pm Oct 8, 2004 CDT
... and if that doesn't work:
(3) try a
b clean uninstall
prior to reinstalling:
Da Gopha, "iTfW: stepwise clean uninstallation of iTunes", 09:51am Apr 5, 2005 CDT
post back to let us know if you got any joy.
love, b

Adobe & Flashbuilder 4 are brain dead !!!

I have spent several hours spinning my wheels with the following problem. Within the same Workspace my pre-existing projects continue to work. However, I purchased a small project from ActiveDen.net and it is throwing the following error. I have installed and re-installed the Flash Player to the latest debug version without anything being resolved. How the hell can this possible, within the same workspace?
Flash Builder cannot locate the required version of Adobe Flash Player. You might need to install the Flash Player or reinstall Flash Builder.
Do you want to try to run your application with the current version?

Yeah, I had that problem, too.. Sorry to say I can't remember how I fixed it, but I think it was a combination of cleaning/recompiling all projects and restarting FB and/or the PC.
I did not install any new player etc.
However, if you want to try that, here is a link
http://blog.ysatech.com/post/2009/07/31/Flex-Builder-cannot-locate-the-required-version-of -the-Flash-Player-You-might-need-to-install-Flash-Player-9-or-reinstall-Flex-Builder-Do-yo u-want-to-try-to-run-your-application-with-the-current-version.aspx

LUMIA 928 BRAIN-DEAD FRACAS

OK...upgraded from an HTC Trophy to a Nokia Lumia 928 in August 2013...since then the Lumia has 'frozen up'...'locked up' THREE times. First two occurances, the pressing low volume and start buttons together for "soft re-set" worked fine -
however----latest incident (Wed. Nov. 6), "soft re-set" unsuccessful, phone shows "invalid SIM card" and calls coming in and going out are inoperable...PLUS phone only works for a few minutes AFTER connecting to charger...BUT email, internet WILL work (albeit only a few minutes)...ANSWERS???? IDEAS????

I have the same problem on all three of my Nokia phones. Customer service sent out a replacement every 30 days and after 30 days my phone turned off completely and is unresponsive to soft or hard reboots.
So i loss all my photos and need to reinstall all my apps and songs and videos again for the third time a whole day of transferring and getting some photos off the cloud again.
I wish customer service would admitt that Nokia Windows phone has Major issues they won't even exchange it for an iPhone or Android phone They only can give me a rebuild Nokia phone again for the FOURTH TIME
David
Software Engineer

Late and brain dead !!! Easy Answer needed

Using Coldfusion9 and dreamweaver cs3 --- What do you call the . . . .more at the end of a statement for a long 'Remarks' or 'Discription' like on a search page?? Thanks

Are you referring to the ellipsis?
The triple dot ...

Can someone please help this brain-dead 50-year-old?

I have an issue I need help with please!! I have a software program that allows me to add cool effects to text (Flasheff2). However, I can't figure out how to have one group of text fade in after the first group of text fades out. See this example: http://97.74.146.161/Original.swf In the example, you'll notice that the developer was able to have multiple text messages fade in then out again. I know how to create and make one group of text fade in then out, but I can't figure out (layers, timelines??) how to have multiple groups of text, one right after the other.
If this makes sense to anyone, please help me out. It is really appreciated.

The very simplest method is to lay out the text and effects end to end on a single timeline. This will certainly work. A second method is to create each text fadein - fadeout as its own movieClip. Then you can play each movieClip one after the other. A third method is to write a set of tweens for each text object. The tweens can each be in functions which are called sequentially. A fourth method is to use the TweenMax tweening library to write one long series of sequential tweens replacing the actual text at each fade out end.
Each of these will work equally well. The first is the least flexible in terms of timing and content, the last is the most flexible.

Possible, or is Home Sharing brain dead?

iMac with Apple Lossless music library is on same Ethernet as AirPort. iMac and iPad both signed in to me.com. Home Sharing enabled all around via same me.com account.
For some reason, iPad cannot see iMac's shared music; the path is iMac->Ethernet->Airport->iPad. Is this a scenario Apple didn't think of, or am I missing a setup step?
Thanks.

my Macs are hardwired to my time capsule - only my iDevices and a couple of airport express units connect to the network wirelessly. my Ipad can connect to my Mini's library without difficulty.
the setup has been thought of and does work !
you might want to check the following support articles for pointers:
iOS: Setting up Home Sharing on your device
Troubleshooting Home sharing

Gone ACL brain-dead

Similar Messages

Maybe you are looking for