GR with quality certificate required
Hi All,
I have set certificate require in my PO. During GR, it will prompt me whether I have receive my certificate. If no system will post the stock into block stock as I did not active quality inspection lot. So if I have receive the certificate after GR, will this stock be posted to unrestricted stock automatically ? Or I need to do a manual transfer posting?
Please kindly advice.
Hi,
After you get quality certificate you need to do transfer posting. According to my knolwedge system won't post the stock to unrestricted stock automatically. Thanking you.
Similar Messages
-
Re: Quality Certificate requirement At MIGO for raw material
Dear all,
I have a requirement where I want the system ask for Quality certificate while doing the goods receipt. The system should not allow me to process the transaction-MIGO if certificate is not recieved.
Please advice
Regards,
Vivek SharmaHi Vivek,
You need to perform following settings.
Configuration
Follow the path
Run trx QCC0->QM in Logistics->QM in Procurement-->Define Control Keys.
Here create your own control key
Where you can set the rest data as per your requirement but for to check the check box for "Cert Required" is must be activated to meet the requirement relevant to this thread.
Save
Say you have configured your Control Key ZZ01
Now just below this one small configuration is mandatory is Run trx QCC0->QM in Logistics->QM in Procurement-->Define Keys for Certificate Processing
Maintain Description
Execute it and go to "Define Certificate Types"
Here either for your relevant certification type or for new type (if you wish to create new), maintain the data as below
"Certificate Required for Each Purchase Order Item" ==== Active
"Certif. per GR Item" ==== Active
"Certif. check required" ==== Active
"Control W/O Certif." Set any error message, I would suggest to select "Without lot error message, with lot error message"
"Enhanced cert. processing" ==== Don't Activate
"No certif. confirmation at GR" ==== Don't Activate
The rest settings are not important to maintain so leave them blank.
At Master Level
In QM view of MM for the material maintain "QM Control Key" that just created "ZZ01"
and the certificate type that is just created or amended. under the procurement data.
Maintain Q-Info record for Material - Vendor - Plant combination (QI01)
Now as per your requirement system will ask for the confirmation for certificate receipt as Yes/No. under the Purchase Order data in MIGO at item level data.
If you select "NO" to it it will not allow to post the GR.
I hope this is what you were looking for.
Regards,
Shyamal -
Executing TS with DHCP certificate requirements
I have this enviroment, where retriving IP from DHCP requires certificate. The certificate script and package is already done, and it has been working earlier, but when I try to create new boot image media, the script executes too fast and IP is not retrived.
If I then execute the script manualy from WinPE, it goes OK and IP is retrived. So problem is here, that for some reason I cannot create the prestage command right.
I have tried 4 different ways;
1. In boot image properties -> customization -> run prestage command.
2. In boot image properties -> customization -> run prestage command with cmd /c
3. While creating boot media, set prestage command.
4. While creating boot media, set prestage command with cmd /c
I have checked, that package sourse and folder directories are porperly set, there is no typo or missleading paths.
Also problem is, that X:\Windows\Temp\smsts.log does not show anything about executing prestage command.If cmd is just flashing by, then it's not really delaying.
Not sure what you mean by prestage package?
Prestart commands are simple files added to the boot image within the WIM.
Jason | http://blog.configmgrftw.com
By prestage package, I ment the package I use when I set prestage command in boot media. So I have the package with all files required for import certificate script. And I added the delay to the beginning of main command file which executes entire script
and all components.
I wonder, why I don´t have that package available in WinPE, before TS selection, if I try to search it on command line? If I open boot media .iso, I will see the package too.
-
Quality Certificate Requirement
Hello SAP QM experts. New to the site, I admire the work that each of you do and I wish I was that good! I'm in a bit of a bind and I would greaty apprecaite it and thank each of you that can help with my problem. We now want to require our suppliers for certain material to provide a certificate of compliance at goods receipt.
I would like to have the person receiving in the purchase order to have to check a box that says Yes when asked if certificate was received. If she doesn't check yes or tries to do the MIGO without checking Yes, then I would like for the system to reject her MIGO or goods receipt of that purchase order.
I've done quite a bit of digging on this site for a step by step on how to set this up but it seems like all the questions pertaining the same thing are from people that have already done it and have questions about certain steps in the process. I need help on how to implement the process from start to finish.
What T code do I start with? MM02, then QM control key, and Certificate type? Then a QI01? I think I gathered that much so far. But that's about it. I was able to get as far as the screen I've attached, but it still let me process the goods receipt even if I left the Cert. Enclosed? box checked on No.
Please help.Hello,
Yes. It is possible to restrict MIGO if certificate is not received. I see your screen shot of the MIGO screen, you are going in right direction.
If you want to restrict MIGO, in SPRO go to Quality Management --> QM in procurement --> Define keys for Certificate processing --> Define Certificate Types, here select your certificate type (which is mentioned in material master QM view) and select check box for 'Certificate check required' and 'Control without certif.' as 'A without lot: Blocked stock With lot: Error message'.
After doing above settings please check and confirm.
Regards,
Gururaj Kulkarni -
Plz tell me something about quality certificates.
Process from quality certificate creation to certificate delivery to vendor for incoming material
Quality certificates can be generated from QC21 (from Inspection Lot) or QC22 (From Material / Batch).
A Certificate profile need to be setup which consists of SAP Script (or) Adobe form. MICs (Master Inspection characteristics) can be referenced for this.
currently, Adobe Form - new technology can be implemented so that PDF document can be generated with Quality certificate details can be sent to vendor e-mail ID through custom development, if required.
I am not sure std setup for sending the quality certificate directly to vendor
Thanks,
JK -
What are the required settings for Quality Certificate
Hi Team
What are the required settings for Quality Certificate for Raw material from vendor. This is my RR - Result Recording for inspection lot.
Please sugget me T-Code to view this.
Can I see say for 6-9 months RR done insp. lot.
ThanksSettings for Quality Certificate for Raw material from vendor,
Activate QM Procurement key, enter qm control key with certificate and Enter certificate type in certificate field.
There are 2 cases,
u want details of certificate send by vendor
u want to record results and see inspection lot wise results.
case1
depending upon the certificate selected by u, system will give u warning or error msg for certificate confirmation at the time of gr. for confirmation QC51 t_code is used. here status has to be changed to 'filed and inspected' then gr will be allowed.
all these certificates can be dispalyed in QC55 T_CODE.
CASE2
U can record results and see in inspection report tab in QA33
Edited by: YOGINI B THORAT on Aug 4, 2009 -
Quality Certificate Issue with multiple batchs with same delivery note
Hi,
Hi,
My Company Business Process:
Quality certificates are generated prior to the good receipt through IDOC process.
When we receive the goods, GR should look for existing quality certificates and trasnfer the inspection results to inspection lot.
When we are trying to receive for single batch & delivery note, It is looking for existing quality certificates. There is no problem in this senario.
But when we receive the multiple batchs with the same delivery note, system is generating new quality certificates. It is not looking for existing QC which got generated through IDOC process. This is the actual proble.
Note: I am not sure is standard SAP does not supprot to receive the multiple batchs with the same delivery note or not at the time of GR. Please advise me.
Thanks,
SumanIn data origin in certificate profile SAP supports " mix the origins within a characteristic. For example, the results data can originate from an inspection and the specification data can originate from batch determination."
Now here question arises Is batch determination of one batch or multiple bacthes took place against a single delivery note.
As per my understnading it should be one batch with is supported in std SAP. -
Quality Certificate -SPRO & Master Data Requirements
Hello Friends
I have a query On the QM module , Not sure if this is the correct forum . In case it is not , Please suggest me where this should be posted
Query
I have to set up the QM processes for a new plant . Quality certificates needs to be Printed for Batch (QC22 ) & Delivery (QC20)
Can you please let me know what are the mandatory Customization & Master Data settings to achieve the above
Your help & advice will be Really Appreciated
Thanks in advanceDear Sathibabu,
Plz post ur query QM module
just check the below link, where u can post ur query
[SAP ERP Operations - Quality Management (SAP QM);
Regards
kumar -
Upload vendor quality certificate to inspection lot
Hello,
I want to know the procedure to upload the vendor certificate to inspection lot in detail.
I have gone throught SAP library but didn't get much out of it.
Please explain me step by step process.
MimiriRefer to SAP help portal about quality certificate for goods receipt
http://help.sap.com/saphelp_erp60_sp/helpdata/en/90/cff086e36711d1954300a0c930e04c/content.htm
In the material master
-'QM in procurement' is active
-A control key with certificate requirement is set
-A certificate type is specified
You can upload the vendor certificate to inspection lot through transaction QC51.
Regards
Luke -
Quality Certificate for Outgoing (Delivery)
Dear QM Gurus,
Here I am having one scenario where I need to print test certificate for delivery considering inspection characteristics of a finished material and semi finished material at different BOM levels.
Ex:
Finished Material : FERT001
SemiFinished Materials : HALB001, HALB002 & HALB003.
Raw Materials: ROH001 and ROH002
Process: FERT001 produced using HALB003 Produced using HALB002 produced using HALB003 Produced using ROH001 and ROH002
At HALB003 we are going to capture some characteristics and FERT001 I will capture some other characteristics, Now at the time of delivery I want to print both(FERT001 and HALB003) inspection characteristics results in Certificate.
Except FERT001 for all other materials batch is maintaining(No batch Characteristics) for tracking purpose.
I tried some standard procedure like assigning both material in quality certificate and all MICs relevant for both materials. Result origin and inspection spec origin as 03 and Material sort no as 2 where i maintained this material in Materials sequence.
With all the above mentioned settings I tried but I con't able to print the characteristic results of HALB003 in test certificate I can able to get only FERT001 Insp Characteristics only.
Please help me in getting it done, it is critical requirement for our client.
Thanks and Regards,
Krishna Mohan.NSLjust a idea,
use batch dervivation to get all HALB char data into FERT batch abd then print the delivery of that batch. try and come back -
Material Master Quality certificate
Hi,
QM is active for a material. And quality certificate type is assgined in material master for a plant.
I created a PO and then GR. During GR, it is asking to select Yes/No for certificate. Until this is fine.
Now this material does not require any certificate, and material master has been changed accordingly.
As per the material master, it should not ask for Certification at the time of GR.
I created a fresh new PO and trying to post GR.
It is still asking to select Yes/No for certificate.
Did i miss anything else. Is certificate type is assigned in any other place.
Please advise.Hello,
Please check if the Profile assignment to the material is deleted.
1.Choose Logistics ->Quality management ->Quality certificate -> Output -> Certificate profile -> Assignment -> Change.
A dialog box with key combinations appears. In the background you see that the default assignment type (condition type) is QCA1.
2.Select one of the key combinations and then choose Continue.
A screen for entering selection criteria appears. The selection criteria are dependent on the key combination you selected.
3.Enter a key date (proposal: current date) and, if necessary, selection criteria on the selection screen. Then choose Execute.
A list appears with all the assignments that correspond to your chosen key date and selection criteria. Object data, such as the material number, is displayed along with the certificate profile, certificate type, and version.
4.To delete the assignment, select the line with the assignment and then choose Edit -> Delete.
Confirm that you want to delete the line.
5.Save the change that you made to the assignments.
After the assignment is deleted,Change the material accordingly in Quality Management tab.
Hope the information was useful
Regards
Swetha -
Quality certificate - Delivery ,Inspection lot
Dear guys,
Hope every one is doing well
Here is my question, this is the first time i am working on Quality certificates
From sap help came to know that
For Quality certificate for Delivery we need to create a certificate profile , forms that is lay out and contents of the certificate
and we need to assign to material and sales organization or customer
Thats clear for me, but also we need to define the output type as LQCA and LQCB if it is ship to party or sold to party
so i belive that when ever delivery Inspection lot UD is done Quality certifiacte is printed according to certificate profile and output type
i belive that the charactersitics of the inspection lot also printed in the Quality certificate
system gets the information from certificate profile , in the charecteristic assignement
just please someone help me that my understanding is correct
Also i need to know if i want to print Quality certificate for inspection lot how do i set the output type as there is nothing like LQCA,LQCB for inspection lot
please help me what setting i need to do for printing inspection lot Quality certificate
Thanks in advance
RajDear kaushik,
You are great, its just nice and happy to see my first inspection lot print out
thanks a lot
Just another Quick question regarding vendor Quality certificate, there is a requirement that vendor certificates to be scanned and uploaded in sap optical archive link
is there any standard transcation in sap , is there any customization need to done in functional point of view , or i need to work with abaper to create a new transcation code to upload
Throw some lights
Thanks
Raj -
Archive incoming quality certificate from vendor
Hi All,
We are receiving the vendor quality certificate along with the raw material and we would like to store these certificates (in PDF format) in SAP.
As a part of this scenario i have created the quality certificate in QC51 against the PO. But I am unable to archive original certificate which we received along with material from the vendor.
Kindly elaborate what are the customizations settings are required to archive the quality certificate.
Thanks & Regards,
N. LaxmanFirst of all you have to get with your Basis person and find out where you are going to archive your certs too. Most places set up an optical drive for this purpose. This has to be done by basis. They should be able to tell you what the "link" is they have set up for the device and the repository id they have defined.. In standard SAP the link is TOA01. But if there is no device behind this link, your archiving won't work.
In config in QM, quality certificates, process output, define archive link, you would map the "link" to the object type BUS2117, for document types QMICERT and QMICERTPDF. This should be there already hopefully.
If this done, you should be able to archive you incoming COA's.
FF -
SAP QM : QUALITY CERTIFICATE
Hi Guru's,
We want to receive quality certificate from vendor. Vendor does not have R/3 system. He will just send quality certificate as PDF through mail. So is it possible to map this scenario in SAP QM?
Is it possible for vendor to send EDI message (Vendor does not have R/3 System) ?
If vendor does not have EDI & R/3 both is it possible to receive quality certificate as PDF through mail as attachment in our SAP system?
Also if we can map this scenario what configuration is required ?
Also if it is only attachment through mail (without EDI), Are we able to update inspection lot at GR with results in quality certificate?
Thanks & Regards,
Anirudha
Edited by: Anirudha Kelkar on Feb 14, 2011 2:49 AMAnirudha,
You can find all the details in attached link.
http://help.sap.com/saphelp_46c/helpdata/en/90/cff086e36711d1954300a0c930e04c/content.htm -
Settings for Quality Certificates generation
Hello All,
I am a new entrant in the forum. I need your help on quality certificates.
What are the settings necessary for generating Quality certificates in SAP?
SravanHi,
For quality Certificate
In material master QM view Should have to assgn the QM Control Key which controls the Certification and also assign the certificate Type.
Create Certificate profile (Tcode QC01),
Here For which Inspection type you want to create the certificate assign the Origin and type of inspection.
Assign the layout set (with ABAP er's help Required form to be created and assign the name here)
By default QM_QCERT_01
After creation of profile assign this profile to material/materialand customer com bi
Regrds
Praveen
Maybe you are looking for
-
Apex RBAC and Seamless Single Sign ON
Hi , We are building a GBAC (Group Based Acces Control) and SSO Module in Apex (I know .. Reiventing the wheel) as we have budget constraints and there are some limitiations in standard Apex implementation. Problem Space: Apex Version: 4.1.1.00.23 We
-
Photoshop CS4 Extended Graphics Error
Hello Everyone I just recently upgraded to CS4 Master Collection in hopes of using it with my web design job I was hired for. Whenever I go into Photoshop CS4 Extended and I try to "Free Transform" something (an image, a shape, etc) and either the ca
-
Import speed is UNBELIEVABLY slow!
I have converted to LR5 as part of the creative cloud because Apple has chosen to abandon its professional level cataloging and editing software. No big deal, I was planning on moving to LR anyway because of its powerful tools, integration and workfl
-
KM Folders and approval process possibilities
Friends, I have a requriement as below: End user access the portal form and submit. Upon submit it is genearting new PDF file and storing it in KM folder. Now my question is, is it possibe to setup a appproval workflows from KM vai UWLfor different g
-
Hyperlink using Reader instead of Professional
Aloha all! I have Acrobat Professional 6 and Reader v8. The Professional v6 is the default application for PDFs; however, when a hyperlink opens to a pdf, it uses the Reader instead. How can I get the default application for PDF hyperlinks to use Pro