No receiver agreement for the sender "xyz" to receiver "abc" found

in SXMB_MONI i am getting the following error message when the data has been sent from the IDOC
No receiver agreement for the sender "xyz" to receiver "abc" found
I have specified 3 receiver agreements and a Default receiver (in configured receivers)
so in any case, it should pick it as the receiver
but, still I am getting the above error message
any one faced same kind of issue?
regards,
nikhil.

Hi Nikhil,
Correct me if I understood it wrongly.
You need to copy the IDOC xml data and copy it for testing. XSD is the definition for your XML data.
You should not copy the XSD as the input to the Mapping program.
Follow this steps:
- Go to your Mapping Program
- Click on Test tab
- Click on the SRC tab and copy your XML data here not XSD.
Thanks
Srini
Thanks
Srini

Similar Messages

  • Integrated Configuration- Problem occurred in receiver agreement for sender

    Hi ,  I am using AAE in PI 7.1  and it is proxy to file scenrios.
    When Ia m doing testing  in Integration Directory in test configuration its giving me this error .
    Problem occurred in receiver agreement for sender -<ECCBUSINESSSYSTEM> to receiver -BS_D_EPS,http://abc.com/sap/pi/HR/Qualifications.Qualifications_Async_Out: No receiver agreement found for , -<ECCBUSINESSSYSTEM> , BS_D_EPS, http://abc.com/sap/pi/HR/Qualifications, Qualifications_Async_Out
    ( here it should take interface  Qualifications_Async_In, but logs says it is pointing to outbound interface)
    here  when I am going in to trace logs  then it seems  that are not able to understand  the   receiver interface . rather then it is taking sender inface in logs..
    In trace logs . I am getting
    Receiver Determination
    <Not found>
    <Trace level="1" type="B">CL_RD_PLSRV-ENTER_PLSRV</Trace>
    <Trace level="1" type="T">R E C E I V E R - D E T E R M I N A T I O N </Trace>
    <Trace level="1" type="T"> Cache Content is up to date </Trace>
    <Trace level="2" type="T">Start with given receiver - BS_D_EPS </Trace>
    <Trace level="2" type="T">Using Receiver Determination 00000000000000000000000000000000 </Trace>
    <Trace level="1" type="T">No Relation found - accept given Receivers. </Trace>
    <Trace level="2" type="T">...extracting Receiver from Header: BS_D_EPS </Trace>
    <Trace level="2" type="T">Classic Receiver Determination via Rules. </Trace>
    <Trace level="3" type="T">...create rule engine </Trace>
    <Trace level="2" type="T">No Receiver found behaviour: 0 </Trace>
    <Trace level="2" type="T">Number of Receivers:1 </Trace>
    <Trace level="1" type="E">CL_RD_PLSRV-ENTER_PLSRV</Trace>
    Interface Determination
    <Not found>
    <Trace level="1" type="B">CL_ID_PLSRV-ENTER_PLSRV</Trace>
    <Trace level="1" type="T">I N T E R F A C E - D E T E R M I N A T I O N </Trace>
    <Trace level="1" type="T"> Cache Content is up to date </Trace>
    <Trace level="1" type="T">...There is no Interface Determination configured for receiver party and receiver service BS_D_EPS </Trace>
    <Trace level="2" type="T">Check conditions for (Inb: Party Srvc If) BS_D_EPS Qualifications_Async_Out </Trace>
    <Trace level="2" type="T">...valid InbIf without Condition: Qualifications_Async_Out </Trace>
    <Trace level="2" type="T">Number of receiving Interfaces:1 </Trace>
    <Trace level="1" type="E">CL_ID_PLSRV-ENTER_PLSRV</Trace>
    Operation Mapping
    <Not found>
    <Trace level="1" type="B">CL_MAPPING_XMS_PLSRV3-ENTER_PLSRV</Trace>
    <Trace level="2" type="T">......attachment XI_Context not found </Trace>
    <Trace level="3" type="T">Mapping already defined in interface determination </Trace>
    <Trace level="1" type="T">No mapping configured </Trace>
    <Trace level="1" type="E">CL_MAPPING_XMS_PLSRV3-ENTER_PLSRV</Trace>
    I  have developed the other integrated configuration scenario and this is working fine . 
    please let me know how can I troubleshoot it

    I am using sender as Soap and receiver as File adapter. 
    here  the problem is that  while going for interface deteremination and receiver agreement  it is calling to  Outbound interface .
    It should call the inbound interface. I put all the details correctly and deleted all the objects and crated again for both Ir and Id..
    I put the name of inbound interface  in configuration but while executing its calling outbound interface.

  • Unable to send or receive messages for the Btinter...

    Hello
    I use Windows Live Mail to download my emails. This is working fine on two computers for other BT Internet and Gmail accounts. But one of my main BT accounts consistently receives the following messages on both computers:
    Unable to send or receive messages for the Btinternet (xxx) account. 
    Server Error: 0x800CCC90
    Server Response: -ERR inactivity timeout
    Server: 'mail.btinternet.com'
    Windows Live Mail Error ID: 0x800420CD
    Protocol: POP3
    Port: 110
    Secure(SSL): No
    Unable to send or receive messages for the Btinternet (xxx) account. Your server has unexpectedly terminated the connection. Possible causes for this include server problems, network problems or a long period of inactivity.
    Server: 'mail.btinternet.com'
    Windows Live Mail Error ID: 0x800CCC0F
    Protocol: POP3
    Port: 110
    Secure(SSL): No
    The messages for this account are available via webmail, and sending an email works. 
    I've tried BT Desktop Help, but this simply sends me in the direction of standard advice pages. I have no reason to think the settings are wrong. 
    Could anyone suggest what is going on here please?

    LesHarg wrote:
    Hello
    I use Windows Live Mail to download my emails. This is working fine on two computers for other BT Internet and Gmail accounts. But one of my main BT accounts consistently receives the following messages on both computers:
    Unable to send or receive messages for the Btinternet (xxx) account. 
    Server Error: 0x800CCC90
    Server Response: -ERR inactivity timeout
    Server: 'mail.btinternet.com'
    Windows Live Mail Error ID: 0x800420CD
    Protocol: POP3
    Port: 110
    Secure(SSL): No
    Unable to send or receive messages for the Btinternet (xxx) account. Your server has unexpectedly terminated the connection. Possible causes for this include server problems, network problems or a long period of inactivity.
    Server: 'mail.btinternet.com'
    Windows Live Mail Error ID: 0x800CCC0F
    Protocol: POP3
    Port: 110
    Secure(SSL): No
    The messages for this account are available via webmail, and sending an email works. 
    I've tried BT Desktop Help, but this simply sends me in the direction of standard advice pages. I have no reason to think the settings are wrong. 
    Could anyone suggest what is going on here please?
    Hi. Welcome to the forums.
    For starters, the recommendation by many people is to uninstall BT Desktop help.
    If this has always been the case, rather than a sporadic issue, then it could be an account problem that seems to plague some accounts - and has done for years. Hopefully the changeover from Yahoo! to Critical Path will cure this particular issue. Try the other settings mentioned by Keith.
    Even though some accounts are fine, there is still a possibility that your local security software can interfere. For example if you have email scanning turned on - then this can be turned off to see if that helps.
    http://www.andyweb.co.uk/shortcuts
    http://www.andyweb.co.uk/pictures

  • Is it possible to attach two receiver agreement in the same Service?

    when i configure the receiver determination
    there is one receiver service and one inbound interface
    but i want to send it out with two different agreements
    it seems that i cannot use the two agreement
    except i have two service.
    Is there some advice to handle this?
    Thank you in advance

    <i>there is sender service A, and the receiver service B, but i have two receiver agreements
    in the receiver determination, i only can choose one receiver agreement
    which i want to use the two at the same time </i>
    >>
    A is sender and B is receiver. Then why do you need 2 receiver agreements ?
    there will be one sender agreement for your sender A
    there will only be one recv. agreement. ie a combination of sender service + your inbound interface + your receiver service while you create the recv. agreement for your recv. B

  • Problem when creating receiver agreement for File to IDOC scenario

    I have done the following :
    1. Created two business systems one for the file system and other for the R3 system and also I created two communication channel, one as sender communication channel and one as receiver communication channel.
    2. Created the receiver determination
    3. Created the interface determination
    4. Created the sender agrement
    5. Now when I was trying to create the receiver agreement I want to assign the receiver communication channel i have created to the receiver agreement but the F4 help gives me no records and I am thus stuck at this point.
    Please suggest me how to proceed forward from here.

    Hi ,
    <i>5. Now when I was trying to create the receiver agreement I want to assign the receiver communication channel i have created to the receiver agreement but the F4 help gives me no records and I am thus stuck at this point.</i>
    Make sure that your created communication channel for reciever is under the respective reciever business system and give the same while creating the reciver agrement.
    sekhar

  • How to set up 2 agreements for the same From,To,DocType,Version in B2B11g

    Hi
    I am having an issue in configuring more than one agreement for the same DocType, Version, From and To partner in Oracle B2B11g.
    When I click "Valid" button on the second agreement it errors out saying duplicate agreement is found for the same DocType, Version, From and TO partners.
    Is there any mechanism to over ride this?
    We need to have multiple agreements created for the same To Partner, From Partner, Doc Type and Version. Otherwise we will end up creating multiple partners which is a real pain.
    Multiple agreements are required because we have to set up different Interchange and Group IDs for each transaction.
    -Sriharish.
    Edited by: 840696 on Mar 1, 2011 7:30 AM

    You can not have two agreements for same From TP,To TP,DocType & DocType revision combination in B2B 11g.
    Multiple agreements are required because we have to set up different Interchange and Group IDs for each transactionIs this requirement for outbound or inbound? You may send Internal Properties from back-end to override envelope parameters in Oracle B2B in case of outbound -
    B2B 11G Outbound EDI Envelope Override
    http://www.b2bgurus.com/2008/09/internal-properties-in-oracle-b2b.html (this blog is for 10g, so read concept only, not settings)
    In case of Inbound, TP identification can be done on the basis of exchange, interchage, group. So if any of this can be same then you may have single agreement. Make sure to enable property "Functional Ack Internal Properties" on B2B console (Administration --> Configuration)-
    http://download.oracle.com/docs/cd/E17904_01/integration.1111/e10229/bb_config.htm#CEGEADFJ
    Regards,
    Anuj

  • I have been paying for two edge agreements for the past 3-4 months AND i have not gotten a reimbursment for anything...

      10/11/2013                      
    Debit Card Transaction
    VERIZON WRLS 08253-01 800-9220204 CA         10/09
    $92.30 
    On October 11th I started an EDGE agreement for the NOTE 3. I make a $92.30 payment over the phone (which is listed above). The lady said it would arrive two days after the phone comes out. It didn't show up two days after it came out and my little Droid X went dead on me. I called customer service and asked if the phone has been shipped yet. They said it has not. I asked if I could pick it up in the store instead. They said yes. They said they would cancel the shipment so I can pick it up in the store. I end up going to the store at Torrance Crossroads and I was just about to get the phone. Then sales rep was trying to force me into buying the case and charger package that was a deal with the phone for $100.I said no and he got hurt and quiet over it. 5 minutes later he comes up to me saying the edge agreement is not cancelled and they can not give me the phone. I asked if there is anything he can do or call customer service and verify because customer service told me it could be done. He said no and walked away.
    I call customer service and they say that they stopped the order and told me to go back to the store and try again. I did not wanna see the sales rep at Torrance Crossroads so I go to another Verizon store on hawthorne blvd in Torrance. I try the same process and the same thing happens. I tell them to call customer service and verify what is going on. I wait for 2 hours while they talk to customer service and the financial department. They tell me they will start another edge agreement on my girlfriends line and give me the note 3 so I can use it on my line. They said they waved the fee through some promotion since I went through a lot of trouble getting the phone and I should be getting a check in the mail for the $92.30 I paid on 10/11/13.
    Ever since then I have been paying for two edge agreements at $29.16 a piece. I have also been paying an extra $8 for insurance on a note 3 that I do not have. I have not gotten reimbursed the $92.30 I paid on 10/11/13. I have been calling customer service since December and have not gotten any where. Today was the last straw when the guy put me on hold and I ended up getting transferred to the sales department... What should I do? Is there anyone that can actually help my situation out. I already suspended my line and will do so for the next 5 months until this is fixed.

    @Dakotaep
    I am so sorry to hear of your experience with purchasing your new Samsung Galaxy Note 3!  This definitely should have been resolved in your first call to us.  I would be glad to review your account and ensure the Edge Agreement is corrected.  Please accept my "Follow" request and send me a direct message so I can further assist.  Thanks!
    AnthonyTa_VZW
    Follow us on Twitter VZWSupport on Twitter.

  • Is there a way for the sender of an email to see if it has been read

    is there a way for the sender of an email to see if the email has been read?    

    Some email clients allow for you to request a read receipt, but the sender also has the ability to refuse to send it as well. Much of that is controlled on the receiving end.

  • Secondary Costs Manual Allocation but with a negative debit for the sender

    Hi,
    We would like to do a manual allocation for secondary cost (the sender objet is a cost center and the receiver objet is other cost center). The only way we know to do this, is using transaction KB15N, but with this transaction, system credits a sender object (for example, a cost center) and debits a receiver object (for example, an new cost center). Is it possible to do this allocation but having a debit (a negative debit) for the sender object and a debit (a possitive debit) for the receiver objets? We do not want to have credits, because the credit does not work properly for the cost splitting.
    Thank you really very much,
    Ariana

    Hi,
    If I put the receiving cost center in the sender side and the sending cost center on the receiving side with a negative value, the problem is that the credit is done for the receiving cost center. For the kss2 we have not problems because all of the costs are on the debit, but for the receiving cost center when we run the keu5 we have problems because keu5 transaction does not take properly costs on the credit (it does not consider costs on the credit as negative costs on the debit).
    Does anybody know how can we solve this problema?
    Thank you really very much,
    Ariana
    Edited by: Ariana Landaluce on Jun 23, 2009 8:45 AM

  • I can send emails but not receive them. The sender address was rejected by the server

    i can send emails but not receive them. The sender address was rejected by the server.

    Your mail server doesn't like the sender's address for some reason, perhaps because his mail server has been blacklisted for spamming.

  • I was going to download a book off of Itunes and when I went to download it my zip code didn't match my card so I wasn't able to download it. now I have a pending charge on my account from Itunes for the book I never received, will I still be charged?

    I was going to download a book off of Itunes and when I went to download it my zip code didn't match my card so I wasn't able to download it. now I have a pending charge on my account from Itunes for the book I never received, will I still be charged?

    Digital Editions can open files of .pdf , .epub and .acsm format.
    When you click on a download link from an online bookstore, a .acsm file gets downloaded to the "Downloads" folder of your computer. You need to double click on this .acsm file(if Digital Editions is already installed) to get the book. If you still get a message saying that your computer doesn't have a way to open this file, please manually associate Digital Editions to the .acsm file type OR open Digital Editions and drag and drop the .acsm file onto Digital Editions.
    Hope this helps. Thanks!

  • Remote infrared codes for the Sony STR-DE675 receiver

    Where can I find the remote infrared codes for the Sony STR-DE675 receiver? They are not in the Owner's Manual, nor on the Sony.com website. Thanks.GBP

    If you were getting sound and no picture when you had the Wii hooked up to your surround sound receiver, your TV was probably on the wrong input.  You would have needed to use the source or input button on your TV's remote and changed the input to the component 1 choice, since that is the port you stated you plugged the Wii into on the TV.
    Your cable remote may not be programmed to work with the blu-ray player.  However, I think you're misunderstanding the function of the buttons at the top of your remote labeled TV, Sat/Cab, VCR, etc.  Your cable remote doesn't work like a Harmony remote.  Pushing those buttons at the top of your cable remote are not like pushing the Watch TV or Watch DVD functions on a Harmony (meaning pushing them doesn't change the TV's input automatically).  All those buttons at the top of the remote are for that you're describing are to tell the remote which components to control.  For example, you are watching cable TV and just used the remote to change the channel but now you want to adjust the volume.  You would have to hit the "TV" button on the cable remote to switch the remote from controlling the cable box to controlling the TV.  Otherwise, you'd hit the volume controls over and over and nothing would happen b/c the remote would still think it was controlling the cable box.  Only a Harmony remote (or similar universal remote) can change the TV's input with the click of a function button.
    And to explain why one must change the TV's input when switching components, I always compare the process to the way a tube TV used to work for those that are new to the flat screen TVs.  Think of the way your old TV probably worked - you had to have the TV on channel 3 for your VCR, 4 for cable, etc.  The input changing is practically the same thing with just a few more steps, if that helps to make things any clearer.  LOL
    Nothing I post is an official statment of Best Buy or Geek Squad, it is only a helpful opinion!

  • The Sender unable to receive delivery and read receipts

    The Sender unable to receive delivery and read receipts through ironport (outbound).
    How does the delivery and read receipts works in ironport?
    However, The Sender able to receive delivery and read receipts without ironport (outbound).
    Please help!
    Alex Ling

    Hi Alex,
    At this time, the IronPort does not support positive DSNs ( read recipiects ). Refer to the following Knowledge Base article:
    http://tinyurl.com/yo78ns
    -whardison

  • Why haven't I received credit for the cancelation of Adobe CC subscription?

    Why haven't I received credit for the cancelation of Adobe Creative Cloud subscription?  I was changed $9.99 on 1 November 2013 for the subscription, but I found out that the application had some limitation to my Mac OSX, so I cancelled my subscription on November 9, 2013.  My credit card company informed me that I have not received credit.  My concern seems to be a problem for many Adobe customers.  Adobe is quick to charge, but not so quick on the refunds.

    Hi Eastwindpolarman ,
    We are sorry for the inconvenience you have been facing. Please contact our chat support to get the status of the refund: http://helpx.adobe.com/x-productkb/policy-pricing/cancel-membership-subscription.html.
    Regards,
    Romit SInha

  • Editing The Fax Layout for the Send Message window

    Dear All
    Is it possible to view and edit the Fax Layout for the Send Message windows in SAP B1 9.0 PL52
    Best Regards
    shayan

    Hi,
    Please check SAP notes:
    693493
    - Recommended method for sending a fax via SAP Business One
    693490
    - Verifying a fax layout before it is sent to a customer
    Hope helpful.
    Thanks & Regards,
    Nagarajan

Maybe you are looking for