PPTP dial-in over a PPPoE dial-out

Hi.
How can i do to perform a dial-in server for remote workers using a PPPoE encap in a DSL/ATM enviroment???
Here is my testing config.
sh run
Building configuration...
Current configuration : 1826 bytes
version 12.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
logging queue-limit 100
ip subnet-zero
ip dhcp pool LOCAL
network 172.26.0.0 255.255.0.0
default-router 172.26.0.1
dns-server 80.58.61.250 80.58.0.33
ip audit notify log
ip audit po max-events 100
virtual-profile if-needed
vpdn enable
vpdn-group 1
request-dialin
protocol pppoe
vpdn-group 2
! Default PPTP VPDN group
accept-dialin
protocol pptp
virtual-template 1
isdn switch-type basic-net3
no crypto isakmp enable
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0.1 point-to-point
pvc 8/32
pppoe-client dial-pool-number 1
interface BRI0
no ip address
dialer pool-member 1
isdn switch-type basic-net3
no cdp enable
interface FastEthernet0
ip address dhcp
speed auto
no cdp enable
interface Virtual-Template1
ip unnumbered FastEthernet0
ip nat outside
ip mroute-cache
peer default ip address dhcp
no keepalive
ppp encrypt mppe auto
ppp authentication ms-chap callin
ppp chap hostname prueba
ppp chap password 0 prueba
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
ppp authentication chap callin
ppp chap hostname adslppp@telefonicanetpa
ppp chap password 0 adslppp
ip nat inside source list 2 interface Dialer1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
ip http secure-server
access-list 1 permit any
access-list 2 permit any
access-list 102 permit tcp any any established
access-list 102 permit udp any any gt 1023
access-list 102 permit icmp any any
no cdp run
line con 0
line aux 0
line vty 0 4
login
no scheduler allocate
end
Dial-out aka. dialer1 works fine!!!
but not dial-in.

sorry, i'm using a cisco1721.

Similar Messages

When dialing out I sent the same cid from the two different lines on PAP2

Hello, I'm using a PAP2 adapter on my phone system. When I dial out from line 1 I sent the phone number or callerd ID from line one. When I dial out from line two which is a different number, I'm still sending out the same phone number as that of line one yet, when I call in to each indivial number, line 1as well as line 2 they each ring serparetly and individualy. I wonder if I have missed a step in the setup. Anyone nows how to fix this or where I can get the info needed.
Thank you.

I don't believe that there is any network address binding. The UDP Open VI determines which network card you are using and the UDP read function determines which IP address you pull the data from. Since you are specifying all of the parameters, it should not carry over after you close a session. There may be a wait required for the connections to reset. Are you doing this programmatically, or are you stopping and restarting your VI? Can you send a screen shot of both of your UDP connections on your block diagram?
Nick Keel
Applications Engineering
National Instruments
Nick Keel
Product Manager - NI VeriStand and Model Interface Toolkit
National Instruments

VOIP Dial out issues with SRP547W

Hi All, this is my first post so I appologise if I have posted it in the wrong place up front.
I have recently purchased an SRP 547w replacing an 877w and linksys pap2t voip box.
I have 1 major issue at present - no matter which number I dial, I cannot ring out. I get what appears to be an engaged tone.
History: I used to run the linksys papt2 behind the 877w and it worked without issue. Ports opened and forwarded were:
udp 5060-5061
udp 8000-8001
my SIP port is 5060
the RTP ports are 8000-8001
I know this works on the SRP547 as without them, I cannot make any calls into the system.
These settings worked perfectly on the PAP2T; I have copied them across to the SRP547W and opened the same ports. I can call VOIP device on the specified number, but still no dialing out.
The 2 main differences I can see on the new device 1) The VOIP is integrated into the router so I'm not routing traffic in exaxtly the same way as I was with the PAPt2 and the second being that the SRP547W also has the ability to connect a PSTN line - which I do not have.
I wonder if this has anything to do with the issue?
For the record, I have diabled the firewall - same result; additionally, if I connect the PAP2T to the SRP547 and forward the ports (or enable UPNP) then I can actually dial out which means I think its safew to say that my issue is within the SRP547W.
I can conrim that the SRP547 does 'hear' the tones from the phone. When I dial certain numbers (to force certein codecs) the system responds to them.
If anyone else has had a similar issue, could you help me out with some direction?
I'd post logs, but I'm not sure how to get them off this device (yet) - I've only had this device for 4 days.....

I forgot to post an update.
Get this, I figured out the problem and it was Sun Rocket.
They did a firmware update over night that caused it to break.
After about three months of working with Linksys, Comcast and Microsoft and tyring everything I was told. It still failed.
Then after another month, I finally was contacted by an engineer from Sun Rocket who was giving me advice over everything we already tried.
I asked him if there was a firmware update from the date I put the complaint ticket in. He checked the database and sure enought, that is what it was.
Their firmware update did not work well with the Linksys router. He rolled back the firmware and now it works perfect.
The SunRocket tech said he put me on a list of Sun Rocket Gizmos NOT TO update firmware.
Well , about 2 months later, they updated it by mistake and now I am going through the pains with SunRocket all over again.
I told them how they fixed it but the Level 1, 2 and 3 techs don't seem to know how to roll back the firmware and they did not have any notes from the engineer on what version to roll it back to.
The the root cause was SunRocket's Gizmo.
Trust me, I've tried chaning the MTU to remoting in to the Sunrocket Gizmo and change the bandwith settings ect ect. I've been through the ringer and I still have problems with them.
The SunRocket Gizmo can not handle the high bandwidth like the linksys router can.
Good Luck, I only have SunRocket for another month and I am thnking about going with Vonage or Comcast.
Here is a picture of the SunRocket Gizmo I am using.
Message Edited by TheInfamousOne on 01-05-200709:56 PM
Message Edited by TheInfamousOne on 01-05-200710:00 PM

N73 auto dial out???

Hello all,
Anyone has experienced N73 auto dial out without the owner/user knowing that it is dialling out to valid phone numbers? I have checked the auto-redial and this feature is not activated. So i am wondering if anyone of you have experience this problem before?

Hi,
I am getting the same problem with my N73. But the thing is it is redialling when i am on one call. It is auto dialling the last dialled call, even while i am still on the call.
For example, I have tried a number earlier & now also i am calling the same number means, then the same number is dialled again. This is happeneing to me only when I have connected my headset with the mobile.
More over in most cases, i am unable to dial a number immediately. Sometimes it takes 4 to 5 times to make a call. If i dial, it automatically disconnects.
Is it a firmware problem?
Nokia team has to reply for this issue. I am getting annoyed because of this.
Will Nokia make any update in the next firmware update to give a autolock facility? Because of this, i am forced to install AUTOLOCK software and I dont like that too.Message Edited by bkar81 on 28-Sep-200708:08 AM

Unity Connection 8.6 not able to forward from extension (dial out)

Dear all,
I'm having a problem at a customer where i'm not able to forward calls externally from the Unity (that's a wish too).
Basically here is the request for which I'm having an issue:
- I'm making a menu with a number XXX (CTI Port) with a System Call Handler
- Under that menu i've 3 choices which points to 3 internal numbers (YY1, YY2, YY3) (CTI Ports).
- All the CTI Ports are forwarded to international numbers which are the final destination
So the flow is the following:
NOT Working
- XXX --> Choice 1 --> YY1 --> Forwaded all to 000countrycode
Working
- XXX --> Choice 1 --> YY1 --> Forwarded all to 444 (internal number)
The strange thing is that I tested everything when I was on site by calling internally XXX from an internal number and it was able to forward all my call to the international number ...
If anyone have a clue about what I can do, I'll appreciate a lot ...
Thanks in advance
C.

Hi Taranjit,
The rules are not made to enable unity to dial out, my goal was to permit only internal calls, but in this specific case, the internal number, is a CTI Port forwarded all to the external international number...
I tried the Unity connection system handler from a internal phone and it was working perfectly, but not if the call is coming from outside apparently.
Kind regards
Christophe

MeetingPlace Express 2.1.1.2 Dial Out was not Successful

I'm configuring a MeetingPlace Express v.2.1.1.2 and I can't make the MPX do the call to the guests of a meeting.
I make the configuration test in: Services > Logs > Verify Configuration > Call configuration verification and show the following error:
==============================================================
==============================================================
Call-Config Report
Summary
WARNING:The H.323 ID should match the host name
Valid E.164 Address has been configured
H.323 gateway has been configured
Error: Dial Out was not Successful
Call-Config Report Details
H.323 Details
H.323 enabled : YES
E.164 address : 196
H.323 ID : mpxadmin
H.323 gateway 1 : 010.145.002.030
SIP enabled : YES
DialOut Session Summary
VUI Configuration: 250 Sessions, 250 Confs
*** VUI INTERNAL STATUS UTILITY ***
DebugMenu:
1) Quick Status of all Ports 4) Make Test Call
2) Verbose Status of Port Range 5) Show All Confs
3) Display complete Port Information 0) Quit
Enter the Command (0 -- 100) []: You entered 4.
Enter destination for your call: The Telephone Number is 196. Len is 3
Do you want specific ports? (t -- F): You entered f.
Placing Call .....Call was unsuccessful: Ring No Answer.
DebugMenu:
1) Quick Status of all Ports 4) Make Test Call
2) Verbose Status of Port Range 5) Show All Confs
3) Display complete Port Information 0) Quit
Enter the Command (0 -- 100) []: You entered 0.
==============================================================
==============================================================
That parameter could check?
Here I place information on the configuration of my network:
CUCM v.7.0 --> 10.145.2.10
Voice Gatweay --> 10.145.2.30
In CUCM > Device > Gateway --> Gateway: 10.145.2.20 | Description: Cisco MeetingPlace Express | Type: H.323 Gateway | IP: 10.145.2.20
Please expect your valuable help!
Thanks a lot!
ErnestoG

hi Ernesto,
As the problem you are facing is a dial out issue on MPE, go
through the checklist mentioned below in order to confirm the configuration
is intact.
Here is the checklist :
1.    Ensure that H323 GW is defined on CCM/CUCM.
Device > Gateway > find.
Look for a device name that equals either MPE's hostname, FQDN, or IP
Address.
2.    Ensure that h323 Gateways are configured on MPE.
MPE Administration Center > System Configuration > Call Configuration > H323
Configuration
Ensure that h323 is enabled.
Ensure that you have entered your CCM's IPs in h323 Gateway 1, 2
3.    Ensure that CCM's interface with MPE is up.
Ensure that MPE's IP Address is listed under the "IP Address" column.
Ensure that this IP Address is that of the FIRST NIC on MPE, not the second.
4.    Verify that MPE has the CSS required to call the destination.
FIRST, FIND MPE's CSS:
When MPE places a call, the CSS in question is Device > Gateway > MPE-GW >
Inbound
THEN the relevant config is under Device > "Call Routing Information -
Inbound Calls" > Calling Search Space
SECOND, FIND DESTINATION PATTERN's PARTITION:
If the destination is an IP Phone within the CCM/CUCM Cluster, then the
relevant config is under Device > Phone > click on Directory Number in CCM.
If the destination is a PSTN endpoint/phone, then the relevant config is
under Device > Route Pattern.
5.    Ensure that your user profile is set to allow outdials.
MPE Administration Center > User Configuration > User Profile Management >
Your User Profile > Can call out of meetings should be set to "Yes".
6.    When you place a call from from the CLI, the system applies permissions
from the "Guest" User profile since mpxadmin or root are not Users within
the MPX application. To allow this to work, you need to verify two
settings:
MPE Administration Center > User Configuration > User Profile Management >
Guest > Can call out of meetings should be set to "Yes".
Ensure that the Guest profile is not in a "locked" state.
MPE Administration Center > System Configuration > Usage Configuration >
Allow Guest outdials should be set to "Yes".
Hope this helps!
Thanks,
Karthik

Problem with dial out

I have a SPA2002 adapter which I use with an asterisk server. On the asterisk I have configured call forwarding that can be enabled by dialing *21*number#. The problem is that the linksys adapter won't let me dial *21, it immediately gives a busy tone, I guess because it tries to process it as a service itself. How can I configure the adapter to dial out with *21*? I have tried to alter different parameters of the adapter configuration, but without luck.

You're mixing up two things.. there's the asterisk as in one of the button on your phone, and then there's the asterisk as in your PBX.
hwittenb was refering to the button on the phone.. your phone dialplan needs to allow dialling stuff like "*21*" - so if you can post the dialplan on your phone, we can see if it indeed allows that number to be dialled. I'm guessing it doesn't since the call never gets to your PBX.
There are two essential pieces to tracking down a problem with your VoIP equipment:
The configuration of every device involved
SIP protocol traces
And don't forget: there's no such thing as giving too much information when describing a problem.

How to turn off number sounds when dialing out?

? I have the keyboard sound off already, but, when I dial out the numbers are not silent.

The keyboard is just that, ...the keyboard, ....used only for text, email and web. The phone dialing screen is totally different and is uneffected by any changes you make to the keyboard settings. The only way to silence the phone when dialing out is to either turn the volume all the way down (not logical) or to engage the mute slide on the side of the phone. **Warning, ...both options also turn the ringer off or down. I would like to see apple address this in the next update. Users don't need to hear these loud numbers.

Cannot Dial Out With a Cordless Phone

A month ago I had a phone line installed at my flat. It's a New Build so I was starting from scratch. I've tried two different cordless phones in the socket and neither will dial out. I get a dial tone, but when I punch in a number a voice tells me the number isn't recognised. Yesterday I plugged in a friend's phone which is a big old corded thing that's at least fifteen years old. It worked fine. Another friend says the only real difference is that the old phone isn't digital and that I can't use a digital phone on my phone line. Has anyone heard of this before? I'm not sure what to do. I've had nothing but trouble with BT getting my address and billing wrong and I'm sick of them. I don't want to call again and lose more of my precious life force if I don't have to.

Hi and welcome
Ensure you have unplugged all other equipment when you have tried a different phone.
Have you tried the phone (with no ADSL filter if you have Broadband) direct in the test point of your main socket?
This main socket looks like this.
remove the 2 screws each side of the socket and gently remove the bottom half, just in side the bit left on the wall you will find another socket on the right hand side, plug your phone directly into there and check if you can dial out now.
If you cant dial out correctly to here (i would try a couple of phones), there is a fault outside of your premises and you should report it to your comms provider.
If it works ok to the test socket you have a fault within your premises either on wiring or aparatus.
(If I have helped you in any way to say "Thank You" please click on the star next to the message. Thank You)
If I have solved your Issue please click the "Mark as accepted solution" button.

In Europe can't get 6126 to dial out

I unlocked my Nokia 6126 using AT&T instructions. Now I'm using a United Mobile international sim card. Every time I think I'm dialing out, I'm actually sending a text message. If I write a text, it works and gets to the person I want it to. But I can't figure out how to make a phone call. I ran through a prepaid sim card quick trying to call out and never have accomplished it. I've spoken with the sim card customer service folks and they say it's the phone. There's got to be somewhere within the menu where I can dial out, in other words make a phone call. I'm in rural Sweden if it makes a difference and my sim card is Liechtenstein. I am getting a strong signal. Help!

I think your phone is malfunctioning. Please have it fixed or replaced by a Nokia service agent.

Mobile site - can I have a web button to dial out

If a user has a mobile phone and browses the site - EG looking for a plumber....
Lets say this site says I am a plumber - here's my number......
Can we develop the page so that the user fat fingers the number and it dials out for them?
Thanks

Keep in mind that some smart phones will terminate the internet connection when the phone is dialing out.
If phone features are disabled, it won't do anything.
<a href="tel:13174562564">317-456-2564</a>
Nancy O.

My blackberry is dialing out on its own, explain how this is possible please :)

My blackberry curve dials out the same number without any attempt on my part, for instance I had left my phone on the table and it dialed out. It continued to dial out the same number until I deleted the number from my contacts.This occurred numerous times on separate occasions.
Not only did it dial out that number but also spelled out the name of the individual it dials out on a voice txt. How is this possible?
It does not dial out any other contact and ever since i've delted this contact the phone no longer dials out.
what are some explanations for this problem?

Better news my charger I was using appears to maybe be part of the thing. I wouldn't work so I got my brothers and it charges so is it possible the old charger was shorting it thus the safety bit killed the power? Maybe the angle is just happen stance.

Ports 1,2,3 will not dial out port 0 fine

Dear community,
I could use a little direction..
I have a 2821 "COMHS00ARB" SN: FTX1302A1UP
It has a VIC2-4FXO on port zero I have an analog phone line that functions perfectly, on ports 1,2,3 I get dial tone and they will receive calls but will not dial out.
other interesting observations:
1: If I connect a laptop to GE 0/1 I get not LAN Lights port GE 0/0 is fine and is the uplink
2: the Gig E port on the NME port I can not get LAN lights if I plug cable in from laptop
3: Aux on front of chassis same no lights on LAN
My first thought is to replace the VIC2-4FXO card to see if its faulty
My second thought is that maybe the 2821 has taken a hit from lightening.. however all internal phones seam to be fully functional, although when I select the line on the corresponding LCD hard button I do not get the hard button to light, even on the working line?
Any directions would be greatly appreciated,
Also if I replace card do I need to worry about firmware versions?

Hello,
It seems that the number you are trying to dial is not correct or the dialplan does not recognize it.
HTH,
Alex
*Please rate helpful posts

Unable to dial out in China

my att Curve 8300 is unlocked but I'm unable to dial out, however, I can receive calls. I'm in China. I put the Sim card in
another unlocked phone and it works. When I check my BlackBerry the display reads:
Sim Card: Security Disabled (this top part is in the locked description but the following is in the unlocked instruction) Why?
ID#
Personalization all read Disabled.
I have entered my code to unlock the phone twice, and I'm told if I do it and it fails the third time it will self destruct...or it will
permanently be locked. Any clarity will be appreciated. Thanks.
Solved!
Go to Solution.

1. Whose SIM card do you have in the BlackBerry.
2. Look at this link and compare your screen with the one in the link.. is it truly unlocked?
http://www.blackberryfaq.com/index.php/How_do_I_determine_if_my_BlackBerry_is_%22unlocked%22%3F
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Bad echo while dialing out on a new 8520

Hi,
Been getting bad echo of my own voice when I dial out. The echo starts even before the call gets connected. This is a brand new phone and i've noticed this from the first call itself. Can anyone help with this?

Hi,
I have the same problem too... . I got this phone just 10 days back.
Thanks,
vJ

PPTP dial-in over a PPPoE dial-out

Similar Messages

Maybe you are looking for