(PVID) inconsistency *PVID_Inc Issue

Hello,
Issue: Vlan 1 is in (PVID) inconsistency state on the Core switch for some access switches trunk ports.
Native Vlan is 1 (same on all the switches)
Find the output below:Core Switch (6513)
SW-Core#sh spanning-tree inconsistentports
Name Interface Inconsistency ----------------------
VLAN0001 GigabitEthernet11/1 Port VLAN ID Mismatch
VLAN0001 GigabitEthernet11/2 Port VLAN ID Mismatch
SW-Core#sh spanning-tree vlan 1
Interface Role Sts Cost Prio.Nbr Type
Gi11/1 Desg BKN*4 128.1281 P2p *PVID_Inc
Gi11/2 Desg BKN*4 128.1282 P2p *PVID_Inc
SW-Core#sh logging
%SPANTREE-SP-2-RECV_PVID_ERR: Received BPDU with inconsistent peer
vlan id 1 on GigabitEthernet11/2 VLAN1012.
%SPANTREE-SP-2-BLOCK_PVID_PEER: Blocking GigabitEthernet11/2 on
VLAN0001. Inconsistent peer vlan.
SW-Core#sh spanning-tree vlan 1 detail | inc 11/2
Port 1282 (GigabitEthernet11/2) of VLAN0001 is broken (Port VLAN ID Mismatch)
BPDU: sent 0, received 1173
Access Switch(2960) :
SWITCH 1 (which is connected through 11/2 of CORE SW)
switch01#sh spanning-tree vlan 1
VLAN0001
Spanning tree enabled protocol ieee
Root ID Priority 49153
Address 0018.18aa.aaaa
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 49153 (priority 49152 sys-id-ext 1)
Address 0018.18aa.aaaa
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Uplinkfast enabled
Interface Role Sts Cost Prio.Nbr Type
Gi0/21 Desg FWD 3004 128.21 P2p
Gi0/22 Desg FWD 3004 128.22 P2p
" VLAN 1 is root bridge "
Whereas all other Vlans are working normal.
VLAN0100
Spanning tree enabled protocol ieee
Root ID Priority 100
Address 0014.f1bb.bbbb
Cost 3004
Port 21 (GigabitEthernet0/21)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 49252 (priority 49152 sys-id-ext 100)
Address 0018.18aa.aaaa
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Aging Time 300
Uplinkfast enabled
Interface Role Sts Cost Prio.Nbr Type
Gi0/21 Root FWD 3004 128.21 P2p
Gi0/22 Altn BLK 3004 128.22 P2p
On the Core switch:
SW-Core#sh inter trunk
Port Vlans in spanning tree forwarding state and not pruned
Gi11/2 100-105
I have fixed this issue by forcefully allowing under trunk interface(
even though this the default):
switchport trunk allowed vlan 1-4094
After applying the above command, Core switch output changed to and
the PVID_Inc error went away :
SW-Core#sh inter trunk
Port Vlans in spanning tree forwarding state and not pruned
Gi11/2 1,100-105
I have solved this issue on 3560 Access Switch by applying:
SW-3560(config)#vlan dot1q tag native
Core Switch Logs :
%SPANTREE-SP-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet11/1
on VLAN0001. Port consistency restored.
I have many access switches with the same configuration but WHY I am getting this issue only on some switches. I want to know why this
problem is random in nature (occurring on only some switches).
Secondly "vlan dot1q tag native" is not supported some of the access switches(2960) but this command has applied on the core switch. Should I remove it from the Core switch or keep it there? What is the best
practice? But other access switches are working properly without "vlan
dot1q tag native" command.
How can I fix this issue without applying "switchport trunk allowed vlan 1-4094".
This problem is not solved by SHUT/NOSHUT under the trunk interfaces.
All switching are working in PVST+ mode
Regards,
Anser

Hello Anser,
on an 802.1Q trunk a Cisco switch uses a proprietary version of BPDU to send PVST BPDUs.
This version includes a field that is the vlan-id.
When the external 802.1Q vlan-id is different from the vlan-id in the received BPDU the switch reacts by rising an STP inconsistency.
in this case the switch named
SW-core complains of:
%SPANTREE-SP-2-RECV_PVID_ERR: Received BPDU with inconsistent peer
vlan id 1 on GigabitEthernet11/2 VLAN1012.
so it says it has received a BPDU with inner vlan-id 1 on vlan 1012.(802.1Q vlan-id).
as a result of this the port is placed in an incostistent state.
sw-core doesn't sends out BPDUs for vlan1.
As a result of this the C2960 sees itself as the root bridge for vlan1 even if it has an high switch priority (probably the result of uplinkfast)
to be noted that when the native Vlan is untagged, a IEEE version of STP BPDU for vlan1 is sent out for backward compatibility with legacy 802.1D devices.
The root cause of your issue is probably the setting
vlan dot1q tag native
on core switches.
Tagging the native vlan is useful when you use 802.1Q in Q to avoid to expose the inner vlan-tag in the service provider network.
In a normal campus network you should be fine with default settings that is
native vlan untagged.
>> problem is random in nature (occurring on only some switches).
this is the worst part of this issue.
Also restating the list of permitted vlans may fix.
To be noted that permitting only used vlans on both ends of the trunk is recommended.
C2960 may not be able to run as many STP instances as the number of existing vlans in the campus.
So a trunk allowed vlan list limits the number of STP instances running on access switches and contributes to network scalability.
Hope to help
Giuseppe

Similar Messages

CRM 2013 - Inconsistent javascript issue crash the web client and user needs to reopen

Hello,
We are using CRM 2013 on premise version and almost 600 users are using it. We have some inconsistent JavaScript issue (following is the log for same) which happens to users in a day or two. When this issue occurs user can not work in system and they have
to open new instance of CRM.
Does anybody knows about this error?
<CrmScriptErrorReport>
<ReportVersion>1.0</ReportVersion>
<ScriptErrorDetails>
   <Message>Unable to get property 'location' of undefined or null reference</Message>
   <Line>1</Line>
   <URL>/_static/_common/scripts/main.js?ver=1676323357</URL>
   <PageURL>/main.aspx#313155368</PageURL>
   <Function>anonymous($p0,$p1,$p2){this.$3_3.get_currentIFrame()&&Mscrm.PerformanceTracing.write("Unload",this.$3_3.get_currentIFrame().src);this.$H_3=$p0.toString();this.$26_3();this.$1A_3();this.$1J_3();if($p0.get_isLocalServer())$p0.get_query()["pagemode"]="iframe</Function>
   <CallStack>
    <Function>anonymous($p0,$p1,$p2){this.$3_3.get_currentIFrame()&&Mscrm.PerformanceTracing.write("Unload",this.$3_3.get_currentIFrame().src);this.$H_3=$p0.toString();this.$26_3();this.$1A_3();this.$1J_3();if($p0.get_isLocalServer())$p0.get_query()["pagemode"]="iframe";addPassiveAuthParameters($p0);var$v_0=$p0.toString();if(IsNull($p2))$p2=false;var$v_1=this.$18_3($p0,$p2);if($v_1){if(this.$2z_3()){window.location.reload();return}this.$2d_3();this.$1s_3();Mscrm.PerformanceTracing.write("Navigate",$v_0);!Mscrm.Utilities.isIE()&&this.raiseEvent(Mscrm.ScriptEvents.UpdateTopLocation,null);this.$3_3.get_currentIFrame().contentWindow.location.replace($v_0)}else{this.$10_3();var$v_2=this.get_contentWindow().Sys.Application.findComponent("crmPageManager");if($v_2){!Mscrm.Utilities.isIE()&&$v_2.raiseEvent(Mscrm.ScriptEvents.UpdateTopLocation,null);var$v_3={};$v_3["sourceUri"]=Mscrm.Utilities.getContentUrl(null);$v_2.raiseEvent(Mscrm.ScriptEvents.IFrameReactivated,$v_3)}}window.self.InnerIFrameSrcChangeTimestamp=(newDate).getTime();this.title=$p1;if(window.LOCID_UI_DIR==="RTL"&&$p0.toString().indexOf("PersonalWall")>=0&&window.UseTabletExperience)this.$3_3.get_currentIFrame().style.position="RELATIVE"}</Function>
   </CallStack>
</ScriptErrorDetails>
<ClientInformation>
   <BrowserUserAgent>Mozilla/5.0 (compatible; MSIE 10.0; Windows NT 6.1; WOW64; Trident/6.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; .NET4.0C; .NET4.0E; InfoPath.3)</BrowserUserAgent>
   <BrowserLanguage>en-US</BrowserLanguage>
   <SystemLanguage>en-US</SystemLanguage>
   <UserLanguage>en-US</UserLanguage>
   <ScreenResolution>1366x768</ScreenResolution>
   <ClientName>Web</ClientName>
   <ClientTime>2015-04-20T15:41:12</ClientTime>
</ClientInformation>
<ServerInformation>
    <OrgLanguage>1033</OrgLanguage>
    <OrgCulture>1033</OrgCulture>
    <UserLanguage>1033</UserLanguage>
    <UserCulture>1033</UserCulture>
    <OrgID>{E8BBA7AE-A552-DE11-B475-001E0B4882E2}</OrgID>
    <UserID>{614837CD-448B-DE11-A5E1-005056970D6C}</UserID>
    <CRMVersion>6.1.2.112</CRMVersion>
</ServerInformation>
</CrmScriptErrorReport>

Are you on-premise, or on-line? : It's on-premise
Can you reproduce it on-demand, or is it sporadic?: It's sporadic
There is a mention of loading an iFrame in the error, do you have iFrames on the form that generates this error?
It's not on specific forms, so can't identify that. Yes we have iframes on some forms.
Does it happen on any/all entity forms, or specific ones? Do the entity forms have any custom JavaScript on them?
It's not on specific forms. And yes we have javascript on almost all forms.
Do you have any network problems or slowness in your network? Does the problem happen when the network is busy?
We need to check this on next occurrence.
Do the users that see this error have any unusual add-ins or toolbars in their browser?  This is not for specific user. Its happening for all randomly.
Have you tried other browsers like Chrome or FireFox and do users see the problem there as well?
We need to check only for IE.

Inconsistant exporting issues MK2

Dear Forum
I have a report that calculates a boolean value for the supression of a GF section.
When i run the report through CR and export to pdf the output is fine. When i export to excel i get a series of ghost records appearing that are supressed in the pdf or CR version.
It appears that when you export a report to excel the order of precedance in which formulas are calulated is inconsistant to other exporting formats.
I am wondering iof other users have experienced any thing similar and if so have a workaround.
Thank you all in advance
Paul Marks.
Please ignore my other thread it is very difficult to follow. Apologies to all.

Yes that was my prefered method. Sorry this does not answer the issue.
With Kind Regards
Paul

Inconsistant overlay issues in same project - urgent help needed please!

Hopefully this has not been asked. I searched and found nothing.
The issue is that using overlays works great for two of the three menus in my project, but the third does not display properly when viewing a finished DVD or the TS folder. It looks perfect in simulator.
Now for the details: the menus are pretty simple. They each consist of a Photoshop file with two layers. One is the background buttons (mostly plain text) and an overlay layer (underlines under the text). These are saved as psd files.
When built and viewed, two of the menus operate normally - you roll over the text buttons, and an underline appears beneath them. The third menu does nothing when rolled over, yet if you click on a piece of text, it jumps to the proper section as expected.
I have checked every setting I can think of to make sure everything is the same between the different menus. I even rebuilt the whole DVD from scratch, and made new menus in Photoshop. Each file was made as a "save as" to ensure that the settings were the same. Same for the menus in DVDSP - duplicates of a menu that work properly. Is there something I've overlooked? Is this an issue with DVDSP 3?
Any help or suggestions are most appreciated. This forum is a great resource.

Hi There
The only thing that comes to mind is that something's changing in your button highlight states between your menus. Go to a menu that is working the way you want and select a button. In the button inspector go to the Colours tab and ine the bottom right corner click the Save As Default button. Then go to a menu that is not performing correctly, highlight a button, go to the Colours tab and click Restore Default.
If that doesn't fix it at least you'll have ruled out a major culprit.
Good Luck
B

Inconsistent SPA504G Issue When Answering Calls

Hello,
I have a user reporting very odd behavior with their Cisco SPA504G phone. They get a call and if they pick up the handset in two rings or less, the call doesn't seem to "complete" and they hear nothing. It has been reported however that if they wait until the first two rings have passed, they are able to answer the call after the third ring.
I'm at a loss as to what could be causing the issue since I too have an SPA504G phone and have no such issues, as well as other users. It is isolated to just the one user. I spoke to our phone administrator and according to their logs:
9/11 @ 2:40 : Queue call, the system did not receive a pickup notification and rolled over to the next agent.
9/11 @ 5:23 : Extension 2625 calls extension 2738 which is forwarding to 2747. 2625 Immediately hangs up upon dialing the number, then proceeds to dial 2739. My guess here is that 2625 saw they were dialing the wrong number and quickly hung up.
9/11 @ 5:28 : Queue call, the system did not receive a pickup notification and rolled over to the next agent."
User experiencing the issue is the 2747 ext.
Software Version - 7.4.8a
Hardware Version - 1.0.3
Any help is greatly appreciated and I would be happy to gather any additional information as requested.

Well, after another referral to Orange Tech Support, I finally have a new handset.
I started having more 'crashing' events on my phone when using sms, gallery, camera.
Called Cust Service who wanted to do the same stuff all over again...i.e. reset phone but I insisted that they escalate it.
They got back to me within 72 hours and I had a new handset the following week. Upon checking I now have an up-to-date firmware.
As an aside, the new phone actually feels a lot different. The slide is firmer and more stable and the keypad also feels of a better quality. Anyone had similar experiences?
Cheers,
Matt

Inconsistent Signal Issue

I'm posting this here because I assume it's a software issue.
While stationary, I will have 5 bars of Ev, then it will bounce around to 1,3 etc.. go into roaming, then come back to 5 bars Ev. Sitting another phone next to it yields consistent signal strength. Disabling roaming forces it to stay on the Sprint Network, but the signal strength still bounces around and it hops between Ev and 1x. In a location where I know I have a strong EvDO signal, this still happens.
Checking other Pre forums, there are quite a few people having the same issue. I imagine this doesn't help the battery life. Any help would be greatly appreciated.
Post relates to: Pre p100eww (Sprint)
Message Edited by dayres on 06-07-2009 10:03 AM

I see this as well.
Sprint is a CDMA carrier, and the "signal strength" indication is *not*. It factors in a bunch of things that affect the usability of a CDMA signal, not just raw -dBm, so it's prone to jump around a bit.
My problem, personally, is that at desk-level at my desk in my office, it jumps to 0 and, if I let it, roams to Alltel (I've forced it not to). Hopefully a solution can be found for that, cause that's an RTM error.

Inconsistent Airplay issue

I have a strange issue. I work at a college and an instructor is having a problem with his new 4th gen iPad. He cannot mirror to the Apple TV in his room. I checked everything and found that:
The iPad is on the same wireless netowork as the Apple TV
The Apple TV is working and up to date
The iPad is also up to date.
Other iPads work (my Mini and another person's iPad 3 all mirror to the Apple TV just fine)
His iPad can show photos and video direct from the apps (Photos and Videos work) but no mirroring option.
I have just asked him to reset his iPad to factory and start over to see if that fixes anything.
If something go messed up when he updated to 6.1 would doing a reset actually fix anything?
Thanks in advance for your responses.

I see this as well.
Sprint is a CDMA carrier, and the "signal strength" indication is *not*. It factors in a bunch of things that affect the usability of a CDMA signal, not just raw -dBm, so it's prone to jump around a bit.
My problem, personally, is that at desk-level at my desk in my office, it jumps to 0 and, if I let it, roams to Alltel (I've forced it not to). Hopefully a solution can be found for that, cause that's an RTM error.

RSC does not get files correctly + inconsistent shading issues (Viste 64 bits)

We experience serious trouble with RH 7 update 1 on Windows
Vista 64 bits.
We work with a team on our software helpfile. When a member
starts typing in a topic RH checks out the file. When the topic is
checked-in RSC performs an undo check out and all the mutations are
lost.
Secondly, when we open RSC some files are yellow (shaded).
This is an option of RSC. When we get all topics, some topics stay
shaded. When we view differences, RSC says that the files are
identical.
Any help is greaty appreciated!
Casper Lange
AFAS ERP Software B.V.

Adobe has confirmed (through the Dutch support team) that
they do not support RH7 in combination with Microsoft Vista 64
bits.
We downgraded to 32 bits and we have a much more stable
system.
I just wanted to share this information for anyone
interested.

Why is Self Calibration of 6711 inconsistent

Self Calibration of 6711 using E-series calibrate in Labview RT is inconsistent (error issued: -10842) inspite of warming up the board, ensuring that the board has an IRQ assigned and Front Mount connector being removed. Is calibration for 6711 not supported in Labview RT?

Have you tried using the 6711 as an RDA device and performing the calibration with the configured RDA device? This might get around the error. I hope this helps.
Regards,
Todd D.
NI Applications Engineer

Is there anything suspicious in these Terminal results?

I'm a fairly new iMac user and I have recently been bombarded with spam on my Verizon email account, which I view through my iMac's Mail program. (Except that now that I'm getting so much spam, I've been signing into my Verizon email instead of my Apple Mail account so that I can send all the spam to Verizon's SpamDetector without opening the spam ... another problem in itself since it seems that my Apple Mail program always opens the spam no matter how discreet I try to be while forwarding it to my Junk folder.. and on top of that, Verizon's Spam Detector doesn't seem to be doing a thing for me!) Sometimes it seems that the spam arrives in droves after using particular forum-oriented websites like Trip Advisor and others, but this could just be a coincidence.
I also recently upgraded my WEP on my Verizon Actiontec MI424WR router to WPA2 in accordance with Verizon's July instructions. Since then, I am also having all sorts of inconsistent connectivity issues with my iMac, my HP 8600 printer, and my iPhone 5s.
Occasionally, it seems that I am being redirected to sites that I didn't ask to see -- nothing really trashy or anything, but for instance, when I was trying to research my problems via Apple Support, I am nearly positive I was being directed to fake Apple Support sites. The main reason I think this is because some of the pages were advertising or directing me to download things that I have been told are not safe -- like fake malware removal programs. I didn't click on any of the links on these pages. Instead, I re-inserted apple.com into my browser and came up with a more official-looking apple.com home page.
Other than my first massive spam issues ever (in over 20 years with the same email address), and the connectivity issues that I've been having since upgrading to WPA2, and what occasionally appears to be redirected websites, I have no other reason to research malware issues. But I'm suddenly having so many little irritating issues with my iMac that I began to suspect that I MIGHT have a problem.
After reading several forums and solutions on the Apple Support site, it occurs to me that I MAY have updated Adobe Flashplayer from a third-party website. I do recall being surprised at the frequency with which I was directed to upgrade Adobe Flashplayer, but I did it anyway because it seemed official and because I didn't know that there was a known security issue with Adobe Flashplayer. And maybe the updates WERE official! I just don't feel like I know anything at this point.
Anyway, I saw a response by Linc Davis that directed a community member to take several copy and paste steps with Terminal. I have followed Linc Davis' instructions and got these results:
Last login: Wed Aug 20 17:53:39 on console
xxx-imac:~ xxx$ kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}'
xxx-imac:~ xxx$ sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|edu\.mit|org\.(amavis|apache|cups|isc|ntp|postfi x|x)/{print $3}'
Password:
com.oracle.java.JavaUpdateHelper
com.oracle.java.Helper-Tool
com.adobe.fpsaud
xxx-imac:~ xxx$ launchctl list | sed 1d | awk '!/0x|com\.apple|edu\.mit|org\.(x|openbsd)/{print $3}'
com.oracle.java.Java-Updater
com.adobe.ARM.202f4087f2bbde52e3ac2df389f53a4f123223c9cc56a8fd83a6f7ae
xxx-imac:~ xxx$ ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta} * L*/Fonts 2> /dev/null
/Library/Components:
/Library/Extensions:
ATTOCelerityFC8.kext
ATTOExpressSASHBA2.kext
ATTOExpressSASRAID2.kext
ArcMSR.kext
CalDigitHDProDrv.kext
HighPointIOP.kext
HighPointRR.kext
PromiseSTEX.kext
SoftRAID.kext
/Library/Frameworks:
AEProfiling.framework
AERegistration.framework
AudioMixEngine.framework
NyxAudioAnalysis.framework
PluginManager.framework
iTunesLibrary.framework
/Library/Input Methods:
/Library/Internet Plug-Ins:
AdobePDFViewer.plugin
AdobePDFViewerNPAPI.plugin
Default Browser.plugin
Flash Player.plugin
JavaAppletPlugin.plugin
Quartz Composer.webplugin
QuickTime Plugin.plugin
flashplayer.xpt
nsIQTScriptablePlugin.xpt
/Library/Keyboard Layouts:
/Library/LaunchAgents:
com.oracle.java.Java-Updater.plist
/Library/LaunchDaemons:
com.adobe.fpsaud.plist
com.oracle.java.Helper-Tool.plist
com.oracle.java.JavaUpdateHelper.plist
/Library/PreferencePanes:
Flash Player.prefPane
JavaControlPanel.prefPane
/Library/PrivilegedHelperTools:
com.oracle.java.JavaUpdateHelper
/Library/QuickLook:
iBooksAuthor.qlgenerator
iWork.qlgenerator
/Library/QuickTime:
AppleIntermediateCodec.component
AppleMPEG2Codec.component
/Library/ScriptingAdditions:
/Library/Spotlight:
Microsoft Office.mdimporter
iBooksAuthor.mdimporter
iWork.mdimporter
/Library/StartupItems:
/etc/mach_init.d:
/etc/mach_init_per_login_session.d:
/etc/mach_init_per_user.d:
Library/Address Book Plug-Ins:
Library/LaunchAgents:
com.adobe.ARM.202f4087f2bbde52e3ac2df389f53a4f123223c9cc56a8fd83a6f7ae.plist
Library/Services:
.localized
xxx-imac:~ xxx$ osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
iTunesHelper
xxx-imac:~ xxx$
I replaced personal info with "xxx." I have no idea what any of it means. Can anybody interpret for me? Is there anything to be worried about within my results?
I have OS X Mavericks Version 10.9.4. My Safari version is Version 7.0.6 (9537.78.2).
Thank you in advance!

Extensions now reduced to:
Facebook Cleaner
eWallet AutoPass
Facebook Improved
Facebook Photo Zoom
Ultimate Status Bar
ClickToFlash
clea.nr Videos
GiveasyouLive
Save to Pocket
JavaScript Blocker

SharePoint 2010 Search "Did You Mean" | How does it work?

My customer has raised a concern that "Did you mean" functionality works inconsistently and issue is explained as below:
1. When I search for misspelled word such as "Maketting" , search page displays the option "Did you mean ""Marketting"?
2. When I search for another misspelled word "Marktng", I get no result and no "Did you mean" option.
I believe there is a dictionary which maintains the mapping between misspelled word and the correct words but I was unable to track the location whether it is in database or a file system. Has anyone faced this issue and know the solution? Below article
talks about a "Dictionary lexicon" but not sure about the location in SharePoint 2010 farm.
http://www.petestilgoe.com/2009/10/sharepoint-search-how-features-work-part-1/
Thanks and Regards
-DB
DB

Hi Deepak,
“Do you mean” functionality is enabled by selecting Query Suggestions in Search Box web part.
Suggestions are automatically built based on what search results are actually clicked on. It takes 6 clicks within a year for SharePoint to add a suggestion.
However, if an administrator needs to add a suggestion manually this can be done using the SharePoint 2010 Management Shell (PowerShell).
I recommend to use PowerShell to check all the suggestions in the Search Service Application, and then remove the one that you do not need.
$ssa=Get-SPEnterpriseSearchServiceApplication
Get-SPEnterpriseSearchQuerySuggestionCandidates -SearchApp $ssa
Remove a suggestion, such as “Marketting”:
$ssa=Get-SPEnterpriseSearchServiceApplication
Remove-SPEnterpriseSearchLanguageResourcePhrase -SearchApplication $ssa -Language En-Us -Type QuerySuggestionAlwaysSuggest -Identity "
Marketting "
More references about the query suggestion:
http://blogs.technet.com/b/chad/archive/2010/06/24/tip-34-adding-a-sharepoint-2010-search-suggestion.aspx
http://sharepointfieldnotes.blogspot.jp/2011/09/sharepoint-2010-search-query.html
Thanks,
Victoria
Forum Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
[email protected]
Victoria Xia
TechNet Community Support

Lenovo Ideapad U410: Display not working after sleep and/or restart

Hello all,
I am recently having some inconsistent display issues with my Lenovo U410 laptop i7 1TB with a Windows 8 PRO upgrade (came with windows 7).
When I press the Power Button on my laptop to put it to sleep, the Screen turns black as if it is off, but the Power & Battery LEDs on the front of the laptop remain on, as well as the LED on the power button. However, when I try to wake my laptop, there is no response on the screen (remaining black as if it is off). The internal fan is running, however I receive no feedback when "blindly" trying to input my password.
I've tried to turn the power off and back on to no avail. I've also removed the power source and held the power button for a couple of seconds and that did not solve the issue either. I've tried connecting the laptop to a screen via HDMI (since there is no other AV port on the device), but there was no signal being sent through.
This is an inconsistent issue that began yesterday 6/11/2013. When the laptop is left alone for a little and is turned on again, the display works, but after closing the lid (sleep) or pressing the button, the display fails to turn on upon awakening.
In most recent circumstances, Today (6/12/2013) I was installing a Windows update that required my computer to restart. When the update configured perfectly BEFORE it was restarting, but AFTER the restart, my internal fan began to work, but the display was not on.
Does anybody or Tech support know what may cause this inconsistent behavior? or know any solutions to this issue?

I am facing similar problem - post sleep & sometimes on touchpad event - the screen gets stuck & a strange array of gray screen comes or the existing screen's colors get distorted & the laptop gets stuck.
model - Lenovo U410; 64 Bit; Windows 7 Home basic;, Intel core i5 processor
I have upgraded display drivers but that hasn't changed anything. Any help is appreciated.
Link to Image
Mod edit: Changed oversize pic to link per forum rule: 50k limit on pics. Please use a hosting site and a link or resize the oversize pics.

Save As PDF bugs

Hi All,
In the past, I've always printed to PS via the Distiller instance, but now we have new branding with spot colors used in the FM templates, so now Save As PDF is a must.
I am finding what I think to be a bug, because it is consistently reproducible. When I Save As PDF choosing Page Range: All, I can get all of the pages printed with spot colors and working hyperlinks, BUT the leftmost cell of the first row of every single table is empty, even though the FM screen itself displays the row's contents.
Here's the PDF outcome — please note the first body cell of the table is empty:
All tables in the document have the same issue. I tried opening other documents, they all have the same behavior. I tried importing formats from other tables, creating new table formats, etc., and the same issue persists, even when I copy-special the char formatting of a cell that does print and paste it to the non-printing cell.
Here's what the same section looks like in the FM window:
However, when I Save As PDF choosing Page Range: 1 to [last number], the contents of the first cell in the first column of the first body row of the table displays perfectly fine, but of course none of the hyperlinks work. Here's that outcome:
If that cell didn't print in any table of any output, it would likely be some kind of formatting issue, but that's not what's happening. The cell prints anytime that I do NOT Save As PDF for ALL pages (which leaves the less-than-satisfactory options of either no working hyperlinks, or pgf/char/tbl format colors generating RGB while the imported graphics on the ref pages retain a different color output that's nearer the spot color).
It's annoying to have to choose pages 1 through (whatever is last) to get all of the rows of all of the tables to properly display, but I would do that as a work around if the hyperlinks worked. However, having to choose between either getting all the tables' body rows complete, or having all the hyperlinks working, or getting both of those but no spot color (which is what happens when I print to PS, yielding inconsistent color issues) is making me choose between lose, lose, or lose.
Is there a patch or work around for this issue, or am I going to need to either convince Marketing that branding guidelines for color in their tech doc suite doesn't matter, or pay USD$2000 to get a PDF processor that links everything on the backend just to get all the content and colors right, and add the links post-PDF creation...? Perilous choices. (You can choose to lose your eye, lose your ear, or lose your arm, but you cannot keep all three. Choose. 'Tis but a flesh wound. Monty Python must have written the script.) I'm sorry, I don't mean to sound exasperated (or exaggerated, as you wish); I have never had this kind of issue with FrameMaker before, and I did a lot of talking around here to convince them to buy the new TCS5 as the best solution for their PDF and online help deliverable needs.
Maybe I'm idealistic, but it doesn't seem too much to expect a program as mature as FM to create PDF output that supports hyperlinks, retains spot color, and actually displays all the text relatively WYSIWIG to the FM interface... Surely I'm missing something, or this is a bug with a work-around, right...?
Any insight would be greatly appreciated.
Rene

Thanks for chiming in.
We've got Pantone 307 CVC as the spot color on H2 text and table header backgrounds, as well as several character formats (bullets, hyperlinks, etc.).
In FM, Help > About shows version as 12.0.1.331. Is there a newer patch?
The PDFs are multi-use, because some customers use them as print material, while others use the PDF directly in electronic format. (Audience is international: UK, EU, all over the Americas, as well as some in east Asia and Russia. Yes we have more issues to address than this, but that's another topic for another post at another forum.)
Marketing doesn't like how green the Pantone 307 CVC renders in the PDF when we use the PS>PDF option, so that's why we started using CMYK output = Save As PDF. ("Whether it's in the PDF or printed, it's supposed to be consistent with the blue in the logo, not a teal color.")
I wonder if the better solution might be to find an RGB visual equivalent...
Row background colors alternate 3% and 10% every other row. I have the same results whether I use the standard Dark Gray from the FM color catalog, or Pantone 444 CVC. The only font in play is Calibri. Heading row background is Pantone 307 CVC with 10pt Calibri 100% White text for headings. Cellbody text is 9pt Calibri 100% Black text (colors from FM stock color definitions).
I was going to upload a sample FM file, but I don't see a way to do so...?
Rene

Different colours shown in Lightroom.

Hi everyone,
Have been struggling with lightroom colours since i downloaded the trial version.
Technical Info:
All images used are Jpeg and nothing to do with RAW
Monitor: DELL 2209WA
Original profile: SRGB
Calibrated profile named Spyder pro 3
Calibrated by: Spyder pro 3
Lightroom version 3
Photoshop cs 5
SRGB in camera settings
Have been researching online for weeks since i have the colour problem and tried all sort of methods mentioned in forum and several website.
The jpeg colour straight out of camera shown on the monitor using firefox, photoshop and picasa photo viewer seem different from the version in Lightroom.
The jpeg imported in lightroom shown is more yellowish in colour, extra effort have been taken to make sure nothing has been changed during the importing process, all presets unchecked etc.
To ensure the colour in lightroom is a permanent colour view and not a temporary view. Exported it using SRGB and Calibrated profile.
If exported using SRGB, the colours will go back to the original colours shown in monitor. If exported using calibrated profile (Spyderpro 3) The colours of the jpeg (yellowish) in lightroom stays. (Viewed in firefox and picasa viewer)
However if viewed in photoshop, choosing embedded profile or convert to working space shows lightroom colours and if discard embedded profile is choose, the default colours shown in monitor is shown.
The colour profile used in photoshop is Spyper pro 3, and embedded profile in photo is SRGB
Calibration is done by adjusting brightness and RGB sliders to adjust white balance and kelvin as close to 6500k and luminance of 120.
After calibration, i will change the
device profiles in advanced to spyder pro 3
and viewing conditions profile to WCS profile for SRGB conditions
Default ICC profile is Spyder pro 3 afer calibration.
Conclusion, the initial colours shown in different program, esp lightroom vs the rest make me hesitant on which colours to trust and which to do editing on. I have no issues with the exported Jpeg, which i can get them to the colours i want.
Resetting all profiles to default(SRGB) solved this inconsistent colours issue between lightroom, photoshop and other programs, but now they are all consistently incorrect.
One problem solved in lightroom colours creates another problem, and this is already the third biggest problem i have.
I was having the export problem with colours, and after researching, found out that a matrix profile over LUT profile will solved the exported colours issues, but now with the matrix profile, i am getting inconsistency with the initial colours.
Many thanks in Advanced
YH

Do you have screenshots illustrating this?
Also, you have to be more specific about what you're comparing Lightroom with. Browsers are all over the map with regards to color management - IE, for instance, will not use the monitor profile, but substitute sRGB. XnView I know nothing about, but again, many applications claim to have color management when in reality they miss at least half of it.
And since you say you have the "same problem" as the previous posters, there are a lot of confused ideas there about what color management means - one of them even embeds the monitor profile in the exported file, which defeats the whole purpose and actually turns all resemblance of color management off.
So just to have it established: A fully color managed application, like Lightroom, converts from the source/document color profile to the monitor profile, on the fly, and that's what goes to the display. Of the web browsers, only Firefox and Safari will do that, and even then it requires that the document profile is embedded and doesn't get stripped somewhere (which can happen).
All that said, it is of course possible that the Spyder is making bad profiles. It could be that the sensor is malfunctioning. First of all I would check for software updates from Datacolor.
Another thing - what is your monitor model?
EDIT: Windows Picture Viewer (not to be confused with Windows Explorer) is fully color managed and should display identically to Lightroom. How does it look there?

Log and transfer inevitably crashing FCP

We're editing a couple of music video in FCP 6.0.1.
we shot with an HMC150 so the clips are being uploaded from an SDHC in an AVCHD folder via log and transfer. the first video went relatively fine barring several problems with log and transfer (files not matching thumbnails, files corrupting, FCP crashing) the problems seem to be random and inconsistent, as issues like a misplaced thumbnail or corrupted import could be reopened and fixed so there was no way to tell exactly why each thing was happening. eventually it all subsided and work went smoothly.
went on to finish video number two and after several imports the log and transfer feature has decided to be the death of the project. Choosing log and transfer inevitably leads to an almost instant crash of FCP unless all drives it's reading from are disconnected. reinserting any drive means an instant crash. the drives are not corrupt and function just fine with any and all other programs, even imovie.
why in the world can't i get FCP to stay alive when i open the log and transfer? please help.

Right - I've solved this one. It turned out that I'd recorded some 1080p50 footage. The mere presence of this on the card freaked Log & Transfer. The camera doesn't make it easy by hiding that footage when you're looking at 1080i25 (or whatever "normal" mode is).

(PVID) inconsistency *PVID_Inc Issue

Similar Messages

Maybe you are looking for