QoS 881 router not policing

Hi,
I'm trying to setup QoS policing to limit bandwith for some protocols. I'm using a 881 router.
I just want to police the traffic for the protocols and configured this:
class-map filetransfer
match protocol itunes
match protocol bittorrent
match protocol ftp
policy-map qos_filetransfer
class filetransfer
police 100000
   conform-action transmit
    exceed-action drop
int f4
service-policy input qos_filetransfer
service-policy output qos_filetransfer
But when I'm testing to download a file with ftp the traffic is not limited.
If I run: sh ip nbar protocol-discovery stats bit-rate top-n 10, I can see the ftp traffic:
FastEthernet4
Last clearing of "show ip nbar protocol-discovery" counters 00:05:03
                            Input                    Output
   Protocol                 5min Bit Rate (bps)      5min Bit Rate (bps)
   ftp                      3340000                  104000
   stun-nat                 14000                    97000
   ipsec                    1000                     1000
   icmp                     0                        1000
   isakmp                   0                        0
   dns                      0                        0
   skype                    0                        0
   unknown                  0                        1000
   Total                    3355000                  204000
If i run: sh policy-map interface f4
FastEthernet4
Service-policy input: qos_filetransfer
    Class-map: filetransfer (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0000 bps, drop rate 0000 bps
      Match: protocol itunes
      Match: protocol bittorrent
      Match: protocol ftp
      police:
          cir 100000 bps, bc 3125 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0000 bps, exceeded 0000 bps
    Class-map: class-default (match-any)
      96296 packets, 139493940 bytes
      5 minute offered rate 3050000 bps, drop rate 0000 bps
      Match: any
Service-policy output: qos_filetransfer
    Class-map: filetransfer (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0000 bps, drop rate 0000 bps
      Match: protocol itunes
      Match: protocol bittorrent
      Match: protocol ftp
      police:
          cir 100000 bps, bc 3125 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0000 bps, exceeded 0000 bps
    Class-map: class-default (match-any)
      59355 packets, 7299832 bytes
      5 minute offered rate 161000 bps, drop rate 0000 bps
      Match: any
Seems that the Class-map class-default are matching the packets, but I have not configured any class-defaults.
Please advice what to do.
Thanks

Hi,
Tested but can't get it to work.
I have tested:
class-map filetransfer
match protocol itunes
match protocol bittorrent
match protocol ftp
match any
and:
class-map match-all filetransfer
match protocol itunes
match protocol bittorrent
match protocol ftp
match any
and:
class-map match-any filetransfer
match protocol itunes
match protocol bittorrent
match protocol ftp
match any
I still get full bandwith when downloading a file with ftp from internet --> a computer on vlan1
Any more idea?
router#sh policy-map interface f4
FastEthernet4
Service-policy input: qos_filetransfer
    Class-map: filetransfer (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0000 bps, drop rate 0000 bps
      Match: protocol itunes
      Match: protocol bittorrent
      Match: protocol ftp
      Match: any
      police:
          cir 100000 bps, bc 3125 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0000 bps, exceeded 0000 bps
    Class-map: class-default (match-any)
      260290 packets, 385289380 bytes
      5 minute offered rate 6399000 bps, drop rate 0000 bps
      Match: any
Service-policy output: qos_filetransfer
    Class-map: filetransfer (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0000 bps, drop rate 0000 bps
      Match: protocol itunes
      Match: protocol bittorrent
      Match: protocol ftp
      Match: any
      police:
          cir 100000 bps, bc 3125 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0000 bps, exceeded 0000 bps
    Class-map: class-default (match-any)
      163215 packets, 16962903 bytes
      5 minute offered rate 283000 bps, drop rate 0000 bps
      Match: any

Similar Messages

WRT600N QoS settings do not affect upstream rates

I have recently purchased a WRT600N router as I have a hard wired wired VoIP phone (Aastra 9112i). I have set the QoS priority for the physical Ethernet port that the phone connects to as high and all of the other ports as normal (I have even tried setting all of the other ports to low).
The problem I have is that the QoS settings do not affect the upstream rate. I have Shaw Highspeed Extreme service and have run speed tests to Speedtest.net throught the router and can get 20Meg down and ~1 meg up. When I change the QoS settings on the physical Ethernet port my laptop is connected to, the QoS settings do affect the download rate but the QoS settings do not seem to affect the upstream rate.
Is there any firmware update for the WRT600N where the QoS setting will control/ throttle the upstream rate or is there some other settings I could use on the WRT600N that will provide priority to my VoIP phone.
Thanks,

I just checked the Linksys download page and the firmware version posted there 1.01.35 is the same version I have in my router. Please let me know if there are any development plans for the WRT600N QoS controls so the the QoS setting also police the upstream/ upload rates.
Thanks,

Can a Cisco 881 router create an L2TP/IPsec tunnel via NAT to Windows 2008?

Hi
Was anyone successfull in setting up an L2TP/IPsec tunnel through NAT-T against a Windows 2008/ R2 RRAS server? I am using an 881 router and the layout is someting like this:
Client -> 881 -> NAT -> internet -> Windows 2008 RRAS
The tunnel goes form the 881 to the Windows server (not from the client...).
Thanks
Roland

Hi Federico
Thanks for your help! Much appreciated.
In my case this should be transparent to the client - I would like not to initiate the connection from the client.
Does that makes sense? I am considering L2TP because Windows 2008 R2 doesn't support IPSec tunnels through NAT (2008 R2 being the responder and the Cisco router the initiator of the IPSec connection).
Regards
Roland

881 Router Wireless Module

Hi Everyone,
I was given an 881 router to work on. I was told that it has the integrated wireless module installed, but I cannot see any radio antenna on the device. Is there a command I can run to determine if the wireless module is installed. I tried sh ver and it did not reveal any information to suggest there is a wireless module.
Also in global configuration mode, the command interface Wlan-ap0, is not accepted.
Any help is appreciated. Thanks.

880W antenna is fixed. You can't remove or replace it. So if there's no antenna then it doesn't have one.
The command "sh inventory" that Michael has posted is a pretty good indication as to the exact model of the router you've got. "sh version | b License UDI" command will also help.

Route not determing automatically at sales order level for some sales order

Dear All ,
Route not determing automatically at sales order level for some sales orders.We are using automatic route determination without wt group,eventhough we have configured the required settings
I have checked all the forums but didn't find any solution for the same.
Looking for your inputs .
Thanks inadvance
Regards
Venkat

Hi
1. Copare the Routes which are Automatically determined and which are not automatically determined
2. Have you mainted this route to be RELEVANT FOR TRANSPORTATION without this check route will not get picked up.
SPRO > Logistic General > Shipping > Basic Shipping Function > Routes > Define Routes > Define Routes and stages > Select the Route and check for it's settings > CHECK MARK Relevant for Transport. Without this check the route will not get picked up as of my understanding.
Thanks
RB

Linksys WRT54G Wireless-G Router Not working

I have a Linksys WRT54G Wireless-G Router and it has worked good for a couple months and yesterday it stopped. When I plug it in all the lights are lit even though there arent any ethernet cables connected and the power light blinks constantly. I tried holding the reset button on the back and it didnt help. Anyone know whats wrong or anything I can try to fix it?

You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

Linksys E1200 Router not saving Port Forwarding changes

Hi!
I am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Can anyone assist me with this? I've searched for hours through forums and tech help websites, but I can't find anyone else with this issue.
Issue:
Linksys E1200 Router not saving Port Forwarding changes.
I have tried:
-Restarting the Modem
-Restarting the browser
-Restarting the computer
-Tried to Port Forward through both the Single and Ranged Port Forwarding

Hi there. You can try another browser or a different computer. If it is the same thing, upgrade the firmware of the router. You can refer to this link on how to http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0a6881b90224439b92c8d8f19ca42e5d_21511.xml&pid=80&...

CK11N , bom and routing not copied

Dear all,
At time of costing run through CK11N , bom and routing not copied I have checked all validity/ status /uses / lot size of bom and routing also . but when i will run costing for next month system has copied bom and routing .
plz guide me

Dear Surendra Patil,
Check the costing variant that you use for executing CK11N, is it PPC1?
If this is correct means check in T code OKKN and choose PPC1 and check for the quantity structure
control and check the BOM apllication and the routing selection ID.
This should match with your BOM that you have created and also the routing that you have created.
1. Check the BOM status in CS03---> header.
2.Check the status & usage of routing in CA03,generally it will be
Usage 1 Production
Status 4 Released (general)
3. If you are using Production version check whether have you assigned proper routing group & counter
and along with the BOM.Also check whether is the production version locked?
Check & Revert back.
Regards
Mangalraj.S

E71 GPS 'route not found' when using device only s...

Hi, earlier today I was getting help to not get AT&T network data charges. I have set everything up per direction but now when I try to search for something and navigate to it I get 'Route not found'. Any ideas how to fix this?
Solved!
Go to Solution.

Start with a simple and obvious search string. If you give us an example of a search string that did not work we could have a look at it for you.

WRT54GS "Router Not Supported".

Hello. I have a WRT54GS V.6. I have had it for quite a long time, but just yesterday it stopped giving internet to its wired connection. The wireless connection was working fine. I reset the router (holding the button in for thirty seconds and planned on making a new network). Everytime now it tells me: "Router Not Supported". I looked around the support here, and ended up downloading the firmware upgrade and upgraded the router, reset it once again, and tried once more. Same problem. "Router Not Supported". The power light is on. The WLAN light is on, the Ethernet Port 1 light is on, and the Internet light is blinking. So it IS recieving the signals. I don't understand what's wrong. I have no internet connectivity through the router, either.
Can someone help me?

Further browsing of the forums, and I came across this:
Step 1 : You should just connect the router to main wired computer from ( port 1,2,3,4). No need to connect the dsl modem in this step .
Step 2 : hard reset the router It seems that we will have to reset the device back to the factory defaults. Kindly follow these steps to reset the device:- - While the device is 'ON', press the reset button on the back panel of the device using a pointed object and keep it held for about 60 seconds. - You will notice that the power light on the device would start blinking, indicating that it is being reset. - After 60 seconds release the reset button and switch 'OFF' the Linksys device and wait for 10 seconds and then switch it 'ON' again. - Let the power light on the device stabilize.
Step 3 : wireless settings. Please access the setup page of the router by launching an Internet Explorer and type on the address bar, 192.168.1.1 and press enter. When it prompts for the username and password, leave the username field empty and provide password as admin all in lower cases and then click on ok. Click on the Wireless tab - Here Wireless Network mode should be mixed - Provide any new name in the Wireless Network Name (SSID) box, all in lower cases without any spaces in between. Do not use any old name - Set wireless channel to 11 - And wireless SSID broadcast should be Enabled and then click on save settings.
Step 4 : wireless security
1. When the router's setup page appears, please click on the Wireless tab.
2. When the Wireless area appears, click on the Wireless Security sub tab.
3. When the Wireless Security area appears, select WEP under Security Mode dropdown.
4. Encryption should be set to 64 bits 10 hex digits.
5. Skip the Passphrase box.
6. In the WEP Key1 box, type in a phone number (just the numbers no spaces or dashes) that you can remember in the box.
7. Make a note of these 10 numbers; this would be your wireless network's key.
8. Leave the key 2, key 3 and key 4 boxes blank, and then click on the Save Settings button.
Step 5 : On the 192.168.1.1 set up page of the router , please click on the set up tab . In that you will find an option as local ip address 192.168.1.1 . Please change that to 10.10.10.1 and then hit save settings at the bottom. Once setting's are saved close that page.
Step 6 : confirmation of the physical connection. You should connected the modem router ( internet port ) to main wired computer ( port 1,2,3,4). Now switch OFF both your modem and the router. Switch ON the modem first and wait for about 40 seconds and only then switch on router. At the end of the step 6 try going online from the wired computer . If you are not able to go online from the wired computer than do the step 7
Step 7 : Please access the setup page of the router by launching an Internet Explorer and type on the address bar, 10.10.10.1 and press enter. When it prompts for the username and password, leave the username field empty and provide password as admin all in lower cases and then click on ok. On the main setup page select the Internet Connection Type as PPPoE. - Then provide the username and password provided by your ISP (Internet service provider) for your connection. (Example: [email protected]) - For MTU select Manual from the drop down box and set the MTU size to 1250. - Select the Keep Alive option and choose the redial period as 30 sec
(Originally in BTB's post)
And it worked for me. :] So my problem is solved.

Route not found on nokia maps

Hi can anybody help.
I updated my firmware on my N95 recently and now when I try to plan a route a keep getting 'route not found' message.
I can see the local area map when I get a gps connection but if I type in an address , which is not in surrounding area I get the message above. If I move the map pointer in maps around I can move to an area where roads etc disappear.
For example I have my home address in landmarks and my work (approx 10 miles apart) and even though I'm able to see surrounding maps when I'm at either place it will not calculate a route from one to the other.
Help

We found that the N95 needed to be "on line" before it would calcualte a route.

WRT54G3G – "Router not found" when trying to configure broadband cable network

Hi,
I have a WRT54G3G, v.1.1 router. I have used it successfully for ~3 years with mobile Internet (Huawei E800 card). Recently I installed broadband cable network in my place, tried to configure WRT54G3G to work with it and failed…
I tried manual configuration, and I was not able to set it up. I downloaded „Setup Wizard”, and tried all three options:
a) 3G/UMTS or GPRS
b) Broadband WAN Only
c) Broadband WAN and 3G/UMTS or GPRS
Only option a) can be completed successfully. When I try b) or c), I get following message from „Setup Wizard”: „Router not found, Please make sure the router is properly connected and try again.” I am sure I connected all cables as instructed.
When I plug cable network directly to my PC’s Ethernet slot, it is automatically configured, and all is working fine.
Can anyone advise please what to do? Thank you!
Best regards,
Jakub
Solved!
Go to Solution.

What is the ip address of your router? It seems like the WRT54G3G is already talking to your modem and is getting the connection properly. Make sure that the WRT is not on the 192.168.1.x segment.

Cascaded routers: no internet access when second router not use NAT

Cascaded routers: no internet access when second router not use NAT
Here is my setup:
[pre]
WAN
|
| 74.96.170.x (WAN IP) |
| Router1(Verizon FiOS Router) |
| Model: MI424WR-GEN2 (Rev F) |
| Firmware: 20.21.0.2 |
| Def router: 74.96.170.1 |
| 192.168.1.1 (Local IP) |
|
| 192.168.1.22 (WAN IP) |
| Router2(Linksys) |
| Model: WRT54GL v1.1 |
| Firmware: v4.30.16 |
| Def Router: 192.168.1.1 |
| 192.168.2.1 (Local IP) |
|
| Computer 192.168.2.160 |
| Def Router: 192.168.2.1 |
"q.route" 120L, 4441C written
[m.wang@m-wang-ltm2:/Users/m.wang/m/Network]
$ more q.route
Cascaded routers: no internet access when second router not use NAT
Here is my setup:
[pre]
WAN
|
| 74.96.170.x (WAN IP) |
| Router1(Verizon FiOS Router) |
| Model: MI424WR-GEN2 (Rev F) |
| Firmware: 20.21.0.2 |
| Def router: 74.96.170.1 |
| 192.168.1.1 (Local IP) |
|
| 192.168.1.22 (WAN IP) |
| Router2(Linksys) |
| Model: WRT54GL v1.1 |
| Firmware: v4.30.16 |
| Def Router: 192.168.1.1 |
| 192.168.2.1 (Local IP) |
|
| Computer 192.168.2.160 |
| Def Router: 192.168.2.1 |
| NO iptables, basic setup |
[/pre]
On computer, I have:
[pre]
# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 192.168.2.1 0.0.0.0 UG 2 0 0 enp2s0
loopback localhost 255.0.0.0 UG 0 0 0 lo
192.168.2.0 * 255.255.255.0 U 0 0 0 enp2s0
[/pre]
On Router2, I have:
[pre]
Routing Table Entry List
Destination LAN IP | Subnet Mask | Gateway | Hop Count | Interface
192.168.2.0 255.255.255.0 0.0.0.0 1 LAN & Wireless
192.168.1.0 255.255.255.0 0.0.0.0 1 WAN (Internet)
0.0.0.0 0.0.0.0 192.168.1.1 1 WAN (Internet)
[/pre]
Router2's Operating Mode is Gateway. On Router1, I have:
[pre]
[Router1] Routing Table
Name Destination Gateway Netmask Metric Status
Network (Home/Office) 192.168.2.0 192.168.1.22 255.255.255.0 0 Applied
Network (Home/Office) 192.168.1.0 192.168.1.1 255.255.255.0 0 Applied
Routing Protocol: Internet Group Management Protocol (IGMP)
Default Gateway: 74.96.170.1
[/pre]
On computer, I can run tcptraceroute to yahoo.com OK:
[pre]
# tcptraceroute yahoo.com
Selected device enp2s0, address 192.168.2.160, port 46596 for outgoing packets
Tracing the path to yahoo.com (206.190.36.45) on TCP port 80 (http), 30 hops max
1 192.168.2.1 0.610 ms 0.729 ms 0.735 ms
2 192.168.1.1 1.843 ms 1.378 ms 1.363 ms
3 l100.washdc-vfttp-107.verizon-gni.net (96.241.146.1) 13.620 ms * *
... /* It reached the destination. */
[/pre]
I want to change Router2's Operating Mode from "Gateway" to "Router" because I
want to turn off NAT on Router2 so that I can access all computers attached to
Router2 by their individual IP instead of using port forwarding at Router2.
The problem is after the mode change from "Gateway" to "Router", and regardless
whether I disable RIP or enable RIP, and on what interfaces it is enabled, computer
192.168.2.160 does not have internet connection.
Observations:
[0] INTRAnet works as I can reach computer 192.168.2.160 from computer behind Router1
192.168.1.x and vice versa.
[1] ping and traceroute *work* on Router2 itself using the built-in dianostic tool.
[2] nslookup on computer 192.168.2.160 always works on new lookup. It uses
192.168.2.1 as the resolver.
[3] tcptraceroute stops after step 2:
[pre]
# tcptraceroute yahoo.com
Selected device enp2s0, address 192.168.2.160, port 45999 for outgoing packets
Tracing the path to yahoo.com (98.139.183.24) on TCP port 80 (http), 30 hops max
1 192.168.2.1 2.553 ms 0.534 ms 0.638 ms
2 192.168.1.1 1.342 ms 0.964 ms 0.867 ms
3 * * *
[/pre]
[4] tcpdump shows that computer 192.168.2.160 tries to reach out and nothing is returned:
[pre]
13:34:03.172828 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
13:34:06.175786 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
13:34:09.178804 IP 192.168.2.160.45999 > 98.139.183.24.http: Flags [S], seq 1122548929, win 0, length 0
[/pre]
This is not expected because NAT to internet should still be done by Router1, no? Computer
behind Router1 with IP 192.168.1.x has internet connection.
[5] It looks like I cannot change the Routing Table Entry on Router2. I do not think I need to change anything,
just an observation.
[6] If I use LAN to LAN connection, then both intranet and internet works. [The internet IP of Router2 can be
anything not in the same subnet of the Router1, and DHCP on the local side should be disabled to avoid conflict
with the the DHCP on Router1].

I have a question. Unfortunately in order to ask my question, I have to have a lengthy description of my setup. Basically, I have a second Linksys router in "router" operating mode with NAT disabled connected to the Verizon router, and I have a computer which is in a different subnet (192.168.2.x) behind the Linksys router. This computer can communicate with computers behind Verizon router in subnet (192.168.1.x), but cannot reach internet. This is a simplified version of my question, full details are in the original post.
If I setup the Linksys router in "gateway" operating mode, which means with NAT enabled, then both intranet and internet works, but there is no easy way to setup port forwarding for 10 compueters in 192.168.2.x network to communicate with 10 computers in 192.168.1.x network.
If I setup the Linksys router in a LAN to LAN configuration with Verizon routers, but this way all computers are in the same subnet, I want them to be in different subnet for access control and things like that.
I hope this makes things a little clear.
Thanks.

Routing not Exchanged

Morning all,
I have two rev D MI424WR routers connected to one another via LAN Coax. I can obtain NTP successfully from the router that has the broadband connection, however the secondary router says its still waiting forresponse from NTP server. This tells me that routing between the two is not working properly, as the secondary router should be able to send traffic to the primary router, and then it would be passed out to the Internet.
Do I need to configure the secondary router to allow for routing information to be exchanged successfully?
Thanks,
Steve
Solved!
Go to Solution.

Here's how I see this issue. If the second router is able to allow other devices to transfer data across the network via the main router, there isn't anything wrong with the second router. I don't know how the ActionTec is set up when it comes down to NTP, and if it spends time trying to find other routes to an NTP server but I'm pretty sure this is just a problem due to the fact that it might be trying to use the MoCa WAN or Ethernet WAN port to search for an NTP server. Since those interfaces (OS-wise) are clearly down and that router technically isn't holding any sort of IP address besides it's own, the process is ultimately failing. I've seen it happen on many routers repurposed as access points/switches that attempt to search for NTP servers over the WAN Port.
You'll want to try messing with static routes to allow only the second router to reach an NTP server if at all possible, while having the second router not perform any form of routing function. Something like telling localhost traffic to go out on whichever interface the router is connected to the main network, and tying in information such as IP and Subnet mask of where it needs to go might work.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Routing not found

Hi friends,
i have created routing for finish product .in MTO senario i went for MRP RUN after sales order is entered. .the corresponding planned order is created . but when itry to convert the planned order to production order a message is coming like <b>routing not found</b>.
so please syuggest what to do?its urgent
feasible answer will be awarded
THANKS & REGARDS
OM

OM,
Check whether the routing is having valid status and Usage 1 or 3 - Status - 2 or 4. This you can check in the routing header.
Also check the validity based on Lotsize , whether the sale order quantity is within lotsize mentioned in the header of the routing.
Also check the Validity start date of the routing in the header, the Plannned order start date should be latter than the routing valid start date.
Regards,
Prasobh

QoS 881 router not policing

Similar Messages

Maybe you are looking for