WLC 5508 Discovery in Prime Infrastructure

I have newly deployed a Prime Infrastructure (PI) in my network, and i want to add my wirless controller in it.
I get an error SNMP time out whenever i add my controller to PI through SNMP.
There are default SNMP configurations in the controller and i am simply adding them in PI with their private/public SNMP string.
Is there something i am missing?
WLC 5508 is connected to my core switch and PI is connected to another switch which is directly connected to core switch via Layer 3.
Is there any configuration required to be done on the switch side.?                  

Hello,
Please go through the below link, it may help you to add WLC in Prime Infrastructure (PI)
https://supportforums.cisco.com/docs/DOC-29006

Similar Messages

  • WLC 2504 in Cisco Prime Infrastructure 1.2

    Trying to add Cisco 2504 Wireless Controller, Software Version 7.3.101.0, to Cisco Prime Infrastructure
    1.2 (1.2.0.103), License Evaluation, with no success.
    When using Discovery, Discovery Job show Credential Errors: "Error occured due to invalid SNMP credential"
    When Add Device from Device Work Center I get:
    Reachability is "Unknown", Device Type is empty, Collection Status is "Managed with Warnings", with message "SNMP Failure: No Response for SNMP Get request.", Collection Time is empty.
    I've tried with both snmp v2 and v3.
    I've tried to lower "Maximum VarBinds per Get PDU" to 10 or 20, cause I've read similar problem in NCS.

    I solved the same problem 5min ago.!
    select the device and press syc ..that helped me ...

  • Can we upgrade IOS in WLC 5508 through CISCO prime?

    I have CISCO prime 2.0 and CISCO WLC 5508 HA SSO pair.
    I would like to upgrade the software code for the WLC HA pair.
    Can I do through the CISCO prime ......
    As per the link :http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html#pgfId-43571
    1. After the WLCs are configured in the HA setup, the Standby WLC cannot be upgraded directly from the TFTP/FTP server.
    Prime do the upgrade through FTP server , so will it be ok if we do the upgrade through it, for HA WLC.

    Please check this link to upgrade wLC software in HA setup.
    http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html
    Once the Primary WLC complete the upgrade , it will transfer the entire image to the Standby WLC via the Redundant Port.
    Regards
    Dont forget to rate helpful posts

  • Does Prime Infrastructure 2.0 support 7.5 code?

    I am currently running PI 1.3 and plan on upgrading to PI 2.0. Are 5508 Wireless Controllers 7.5 and MSE 7.5 code supported in release PI 2.0?

    PI 2.0 was really intended for the converged access, but it will also support v7.5 and PI1.4 supported v7.5.
    Management Support for WLC Release 7.5
    Prime Infrastructure 1.4 provides management support for WLC Release 7.5 and associated features. In addition, this release provides support for AP platforms such as 3600P and 802.11ac module.
    For more information about Cisco Unified Wireless Network (CUWN) Software Release 7.5, see the product bulletin at the following URL:
    http://www.cisco.com/en/US/products/hw/modules/ps2797/prod_bulletins_list.html
    For more information about the features of WLC Release 7.5, read the Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 7.5 available at the following URL:
    http://www.cisco.com/en/US/products/ps10315/prod_release_notes_list.html

  • MSE 3355 / PRIME INFRASTRUCTURE 2.1

    I'm integrating a Cisco Prime Infrastructure 2.1 with MSE 3355 for location services and wIPS. I have several questions that I could not clear and would like you to help me giving me some indication with the steps I must take to fulfill these tasks.
    1- The Maps added to the CI 2.1 are not showing the location of the Rogue APs and Rogue Clients seen in the network.
    2.- The AP Clients location is not showed in the Maps.
    3. I require to know what is the process for classifying Rogue APs in the PI 2.1.
    5. I get the message "Collection Failure" of three WLC in the Cisco Prime Infrastructure but the data that the message shows is collected normally.

    I have already resolved this two points:
    1- The Maps added to the CI 2.1 are not showing the location of the Rogue APs and Rogue Clients seen in the network.
    2.- The AP Clients location is not showed in the Maps.
    I still have this questions:
    3. I require to know what is the process for classifying Rogue APs in the PI 2.1.
    5. I get the message "Collection Failure" of three WLC in the Cisco Prime Infrastructure but the data that the message shows is collected normally.
    6.-We have this error message in the allocation profile for a WLC wIPS. (Note, this is WLC version 7.0.250.0)

  • Cannot add WLC 5508 to Prime Infrastructure 2.1

    Regards,
    I've been migrating / implementing a WCS to PI 2.1. I had several problems at first to add the 11 WLC we have to PI which I could be solving by trying and testing as I have not found many references by Cisco when it comes to troubleshooting when deploying PI.
    I have several queries:
    1. The WCS was added 11 WLC using different SNMP communities are configured on each of them. At first when trying to add the WLC had PI SNMP communication problems. I performed the test to eliminate any of the WLC added to WCS and add it again with some communities already existing R / W without any problem. At the end, I could not add the WLC so I had to create an SNMP community with the IP of Prime in the WLC so that they can be added. Does anyone know what is the cause of this?
    2. I could not add a WLC 5508 IOS 7.3 using this method, even creating an SNMP community and IP mask 0.0.0.0 / 0. No access list or FW in between the WLC These WLC are spread over several countries but i was able to add the other WLC adding a community in each WLC pointing to the IP of Prime. It is similar to this case:
    https://supportforums.cisco.com/discussion/12232506/cannot-add-wlc-5508-v761200-prime-infrastructure-21
    Thanks for the help.

    It turns out that this situation was caused by a bug in 7.6.120.0 (CSCuo73572).
    TAC handed me an escalation image (7.6.120.16) that fixed this. 
    Added the controllers sucessfully on the first try. 
    Phill

  • WLC 5508, Prime Infrastructure, 7921 phones and QoS

    Hi everybody!
    I have deployed about 50 wireless cisco phones int the network with 27 APs with the WLC 5508.
    I'm trying to investigate phones behaviour (I have some loss of audio).
    And I use Prime Infrastructure for monitoring.
    I run the Voice Diagnostic on the selected two phones.
    and in the Charts I see the next:
    1. for one phone "Downlink AC Queue Usage" shows all the traffic of "voice packets". but "Uplink AC Queue Usage" shows all the traffic of the "Best efforts packets".
    2. for the second phone "Downlink AC Queue Usage" shows all the traffic of "Best efforts packets". and "Uplink AC Queue Usage" shows all the traffic of the "Video packets".
    that is strange, very strange. the WLAN of these phones uses platinum QoS. none of other WLANs uses "gold" QoS.
    does this mean I have a QoS misconfiguration?
    where may the failure be? WLC? switches? router?
    please, any suggestions...

    I noticed few misconfigurations as per your response
    1. Are you configured AP as FlexConnect ?  If not AP connected switchport should be configured as ACCESS port & trust DSCP. If it is configured as FlexConnect, then you can configure switchport as turnk & in that case you  have to trust CoS using "mls qos trusct cos" command.
    2. WLC connected trunk ports always to be configured to trust CoS not DSCP. Otherwise WLC set QoS value ignored by your switch.
    3. If you WLAN is set for Platinum then you have to configure Platinum QoS profile for 802.1p & set value as 6.
    I would suggest you to verify QoS value preserve across you switch network. You have to take some wireshark packet caputres (as shown in my reference link) and make sure your voice packet DSCP goes into rest of your network as EF. You need to do this for upstream & downstream (from 7921 perspective) traffic. Here is the traffic flow if AP connected to switchport 1 & WLC connnected to switchport 2.
    7921 <-> AP <-> Switch port 1 <->  Switchport 2 <->  WLC <-> Switchport2 <-> Rest of your network
    Once you do this, then you can go to Prime & check those charts to reflect QoS values correctly. Otherwise you do not know where these QoS value get stripped/or modified in your network.
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • CANNOT ADD WLC 5508 HA MODE IN PRIME INFRASTRUCTURE 2

    I have two 5508 7.5.102 in HA mode and i am trying to add theme in cisco prime infrastructure 2 but i am taking back unreachable. Controller can ping the prime. I adding the controller using the management ip address of controller. Have anyone meat thise issue ? I also have problem when adding switches in stack mode (WS-C2960S-48TD-L)

    Hello!
    Check, that the service-port of the wlc is not in the same subnet, as Prime ip address

  • Prime Infrastructure 2.0 Collection Failure for WLC 5508

    Hi,
    We have installed prime infrastructure 2.0 as a VM.
    I added 2 WLCs (AIR-CT5508) in the device work center.
    Both the WLCs are showing as "Managed" but under the collection status it says "Collection Failure".
    When I hover over the message it reads:
    Other Error: Wireless Controller added successfully but some tables had their records dropped as their key fields failed validation"
    Any ideas?
    Thanks
    Satyaki

    Hi Satyaki,
    Try to reboot the WLC ,if possible and then check the status of the issue.
    Regards-
    Afroz
    **Ratings Encourages Contributors ****

  • Cannot add WLC 5508 7.2.111.3 to Cisco Prime Infrastructure 2.0

    Though the Cisco Prime Infrastructure Compatibility Matrix list out that 7.2.111.3 is supported for PI 2.0
    I am not able to add the controller to the PI 2.0.
    The Reachability Status always shown "Unknow" and SNMP Status always shown "No response for SNMP Get".
    There is no firewall between the WLC and PI.
    And ping test shows it is reachable.
    If I try to add controller by non-management port (I know it is not work but I want to try the reachability), the Reachability Status shown "Reachable" but the SNMP Status always shown error.
    And if I use some SNMP testing software to test the SNMP port. SNMP can be quoted.
    I have try to lower down the "Maximum VarBinds per Get PDU" but no luck.
    Any thing I can do to troubleshoot the problem?

    Yes, I follow the procedure but it does not work.
    Another update:
    I add another WLC with version 7.0.98.0. It is fine.
    And I setup another new PI 2.0 and new temporary WLC5508 with 7.2.111.3 to test. It work fine also......
    So, I am wondering the existing 7.2 WLC have problem in responsing the SNMP Get. But I dont have any idea to test....
    Do anyone have idea to test the snmp connection between PI and WLC?

  • Cannot add WLC 5508 v7.6.120.0 into Prime Infrastructure 2.1

    Hi everyone
    Hope you can help us with this issue.
    We already configure the WLC using this guide: http://mrncciew.com/2013/02/14/configuring-snmp-on-wlc/
    snmp v2: enable
    snmp v1: enable
    default port values
    community: incaenic with ip and mask 0.0.0.0 to allow access from any network or ip
    traps receiver:                   community: incaenic                 ip: 10.100.100.15
    when we try to discover the WLC with the PI it gave the error "SNMP Connectivity Fail"
    WLC is on subnet 10.100.102.0/24 and PI in 10.100.100.0/24; there is a Catalyst 3850 between then with no access list on then.
    Did someone can guide us with this?
    Best Regards.
    Alvaro Rugama

    Hi,
    Which version of SNMP are you using?
    If you are using v1/v2 you should be using community string rather than local database credentials?
    Regarding the service port what is the ip address assigned on the service port. From the configuration guide "Prime Infrastructure uses the preferred management IP address from the loop back interface. If the device does not have a loopback interface, Prime Infrastructure uses similar logic to the OSPF algorithm to select the router’s preferred management IP address."
    Hope that helps.
    Regards
    Najaf

  • Prime Infrastructure 2.1 updating 5508 controllers in HA mode

    I'm having the same issue from PI 2.1 trying to import 7.6.130 for my 5508 controllers and it saying "Image not Applicable for this Device" even though I know that image is applicable.
    Also, has anyone ever updated 5508 controllers in HA mode from Prime Infrastructure?

    Your combination of PI (are you sure it's 2.1? not 1.2?), WLC and MSE is not supported.
    You may want to have a look at this matrix:
    http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
    Regards
    Stefan
    PS: Today PI 1.3 and MSE 7.4 have been released - these support WLC code 7.4

  • Prime Infrastructure 2.1, MSE & 5508 Controllers

    I have installed Prime Infrastructure 2.1 with a number of 5508 Controllers with code 7.3.101.0, also I have added an MSE with code 7.0.230.0.  I have an issue with Heatmaps, I cannot view any clients at all, I can see there are clients attached through the dashlet, there are no alarms showing, all MAP's and Controllers are Synched. Help!!
    Access points are:
    AIR-CAP2602I-E-K9
    AIR-CAP3502I-E-K9
    AIR-CAP3502E-E-K9
    AIR-LAP1142N-E-K9
    AIR-LAP1131AG-E-K9

    Your combination of PI (are you sure it's 2.1? not 1.2?), WLC and MSE is not supported.
    You may want to have a look at this matrix:
    http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
    Regards
    Stefan
    PS: Today PI 1.3 and MSE 7.4 have been released - these support WLC code 7.4

  • Prime Infrastructure and WLC 2504 N+1 config syncronization

    I've setup 2 cisco 2504 WLC's in a N+1 configuration, before we purchased Prime Infrastructure.  Now I'm trying to syncronize the configurations between the two devices in PI.  I've setup a configuration group, and it seems using templates will keep the configuration syncronized between the two devices.  Is it possible for PI to automatically create the templates based on the current configuration of the device.  Plus with PI 2.1 it seems like I have to create a template for every section of the configuration, shouldn't there be just one large template that has all the configurations.

    Yes, you should be able to discover templates from the WLC
    HTH,
    Steve

  • Prime Infrastructure 2.2- problems: Wired Detailed Device Inventory report not running / Cisco 5500 WLCs no listed in subgroup

    New installation of Prime Infrastructure 2.2.0 (PI-VA-2.2.0.0.158.ova)
    installed fixes/software/device packs:
    PI 2.2.1 Poodle Fix (installed)
    PI 2.2.1 Maintenance Release (installed,ncs stopped,rebooted)
    Prime Infrastrucutre 2.2 Device Pack 3 (installed,ncs stopped,rebooted)
    Licences installed (ncs stopped,rebooted)
    Added all devices via Bulk Import (Inventory>Device Management>Network Devices)
    Problem 1:
    The Cisco 5500 WLCs are not listed in Inventory>Device Management>Network Devices (see screen shot) but listed under "All Devices"!
    The Cisco 4400 WLCs and the 8500 WLCs are listed within their subgroup.
    Devices are in "Managed State"
    Problem 2: fixed! (Browser issue)
    Problem 3:
    Unable to run "Wired Detailed Device Inventory" report because I get the error message: Failed to run report: Unable to retrieve data for: Chassis Information (if Chassis Information is selected, if System Information is selected I get the error message with ...retrieve data for:System Information)
    All devices do have an "Admin Status = Managed" and the Last Inventory Collections Status = Completed.
    Has anyone the same issues or a tip for me?
    Another topic, the "User Defined Fileds" are not exported when with running a "Device Export" (Inventory > Device Management > Network Devices). ;-(
    BR
    Bastian

    Hallo Bastian,
    I think you still have browser issue, Using IE is still the best with Prime.
    I have exactly same prime 2.2 and installed fixes/software/device packs.
    I have no problem I can see all views. I use now IE 11, with Chrome 42.0.2311.90 and firefox 37.01 I have problems too with lots of views. You have not tell what browser + version you have.
    Since you have same prime 2.2 as me. I have other problems, can you check yours?
    Can you see a functional CLI template page at Configuration > Templates > Features & Technologies:
    https://supportforums.cisco.com/discussion/12481691/can-cisco-prime-22-still-do-simple-ad-hoc-deployment-job-cli-over-all-switches
    Do you have SNMP Connectivity Failed while Verify Credentials  has no errors all green and checked. 
    https://supportforums.cisco.com/discussion/12494786/snmp-request-exceeds-internal-data-buffer-512-bytes-prime-22-asa-5545

Maybe you are looking for

  • What is the use of preview JPEG embedded in DNG?

    I tried converting a CR2 file to DNG, choosing different size JPEG preview, including full, medium and none.  The converted DNG file all look the same when I open them in LR3.  So the image we see in the library and develop module is not the JPEG emb

  • How do I transfer my iTunes library to my ipad?

    How do I transfer my iTunes Ibarra from my MacBook to my ipad?

  • Embedding image in Description part of Appointment

    In my requirement, I have to send an appointment with image as attachment, embedded (in display mode). for creating document, I am using CL_DOCUMENT_BCS  class, inside that class  i am using CREATE_FROM_MULTIRELATED method for creating the document.

  • DNG Files Appearing as Icon not Thumbnail in Bridge CS3

    Hi If I save a Camera Raw manipulated image as a COMPRESSED (LOSSLESS) DNG file it appears back in CS3 Bridge as a DNG Icon and not as a thumbnail. Is there a reason for this and can I get the saved file to appear as a thumbnail. Many thanks

  • Re: How can I change from one subscription to anot...

    I understand that.  But my question was "How can I transfer the money / credit that was paid for the subscription and use that as credits instead? My mom purchased the subscription no more than an hour ago and has not made a single call with it b/c i