AGP Setup For k7n2 delta ilsr

I have a k7n2 delta ilsr mb, in display properties on desk top setting tab then advanced button then GeForce tab under adapter information is Bus and memory. To the right of Bus it reads AGP (PCI mode) shouldn't that read AGP (8X), how can I change this. Ron.

Hi,
No, leave it at 64 or 128.
Go here for an explanation:
http://www.rojakpot.com/default.aspx?location=7&var1=18
Then - Click on:  "Free Access To the BIOS Optimization Guide" near the bottom of the page - then click on "AGP Aperture Size"
Axel  

Similar Messages

  • Best agp card for k7n2 delta ilsr

    Hi again folks
    I'm thinking of upgrading my graphics card as although this card has never let me down its the oldest component in my box, I would like to get something in the sub £100 range, I dont do games but may wish to in future, mainly it would be for photo apps/running-backup-watching dvd's etc. any info would be greatly appreciated tia Hazzo

    I notice your talking in £'s so I assume your located in the UK. 
    Have a look around overclockers.co.uk
    For a sub £100 I noticed a good offer:
    HIS ATI Radeon 9800 Pro - £82
    Also, the 6600GT here is only £103.24 (£106 inc delivery), altough only 4 left in stock so buy now if you want one 

  • Need help with jumper settings for k7n2 delta ilsr

    I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
    Thanks, Ron.

    Hi,
    As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
    Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
    Axel  

  • Kingston HyperX Memory for K7N2 Delta-ILSR

    Hey will my K7N2 Delta-ILSR support the Kingston HyperX serises DDR400-512MB Ram?
    Im looking to buy 2 maybe 3 of these and really want to be sure theyll work.
    http://www.ec.kingston.com/shop/partsinfo.asp?ktcpartno=KHX3200A/256&promo=hx2shp
    I checked the supported ram list for the K7N2 Delta-ILSR  and they wernt on there so i just figured it may be out of date?
    So thanx in Advance for info!
    p.s. It will support 3x 512MB right?

    Has anyone noticed how the Hyper X went from the poor-man's Corsair to being priced equal to OCZ, and usually higher then Geil, as well as usually being very close to Corsair, if not the same? I think only Mushkin beats it out now price-wise...

  • New Modded BIOS for K7N2 Delta ILSR

    MSI K7N2 Delta ILSR Modded BIOS based on Official v. 7.80 BIOS
    download here:

     Description: Access through interface which is on insecure interfaces list detected. Request aborted.
    Interface/Client IP address:
     Date: Wed, 18 May 2005 13:11:17 GMT
    Doesn't work for me 
    By the way did u put the bios to vork with 1.3 vcore like the braziliantech one that does't exist anymore ?
    EDIT: Thanks it's working now 

  • Case Recommendation for K7N2 Delta-ILSR

    Greetings,
    I'm looking for a mid size ATX case that that has the front usb etc. ports prewired as to work easily with a K7N2 Delta-ILSR mb.  By that I mean I don't have to plug each wire individually (with names that don't match) just a plug that goes on the mb.  My eyesight isn't as sharp so hooking up those one wire at a time is tediuous.  Not to mention the lack of starndards   Does anyone know if this is address on the next rev of mb's (with pcix etc).
    Thanks

    Brazos,
    I have yet to see a case that has all the USB wires together, they are all 1 pin at a time. You will find the Antec line of cases very good. (You can always use a magnifying glass to see the pins.) The pin names on the Antec cases are standardized and easy to figure out.
    If you want a good case at a cheap price, then go with the SLK3700AMB:
    If you want a good high end case, then go with the Sonata:
    If weight is an issue, then go with the Super Lanboy:
    Take Care,
    Richard

  • Warranty Length for K7N2 Delta-ILSR

    What is the mfg's warranty length on the K7N2 Delta-ILSR?
    I filled out the online support form earlier today but no response as of yet, and me being the impatient rascal I am, I didn't want to wonder all weekend. I bought it October, 2003 and the floppy drive controller seems to have gone out.
    Thanks!
    HH

    Thank you, Glenn!
    Looks like mine is 2 yrs. & 4 months old. Kind of stinks that I lost 5 months on the warranty by going by the mfg. date instead of date of purchase. Its not worth the hassle & would even cost more to RMA it for the controller. Ahh, but this is IT, the "World of Workarounds". I'll live!
    Thanks for your time, Glenn! 
    HH

  • Temperature reading for K7N2 Delta ILSR

    I have a 2500+ Barton (333 FSB) to work with K7N2 Delta ILSR and 2x256 MB Samsung DDRAM(400 FSB).I use MBM to read my CPU temperatures.Usually 45-47 C idle and 54-58 C under full load.I overclock CPU to 400 FSB and I get LOWER TEMPERATURES!!!!!
     I use 1:1 bios setting for CPU and DRAM speeds either 333 or 400 FSB.
     How can this by possible?

    I use Speedfan which seems to follow the temp in the bios. I've heard that MBM is also accurate. As far as your temps going down on a OC that is very odd indeed.  

  • Anyone help - need I/O plate for K7N2 Delta ILSR??

    I'm based in the UK but will pay P&P worldwide........
    cheers
    D.

    Good luck!
    http://search.stores.ebay.com/ws/search/StoreItemSearch?catref=C5&fcl=3&from=R7&frpp=50&fsoo=1&fsop=1&sacat=-1&satitle=k7n2+delta+ilsr&sbrexp=WD1S&sif=1&sofindtype=0&sofp=4&ssPageName=WD1S
    Edit: If applicable:
    http://www.mycableshop.com/sku/ATXBACKPLATE.htm

  • Linux for K7N2 Delta-ILSR

    Hello,
    Does anyone know of with Linux distro is compatible with the K7N2 Delta Series?
    Sincerely, Deft

    Knoppix worked too, even my TvTuner worked.
    Not that I would recommend Knoppix as a solution, I was just playing.
    There is a lot more support for the nvidia kit now.

  • Accessing RAID BIOS Setup on K7N2 Delta-ILSR

    Dear All,
    OK, OK, OK, so the message title does not make much sense... I wanted to include all the useful words.
    I have a brand new motherboard, as above and I have put a drive onto IDE 3 (yes, you can do this - just have one drive on the SATA RAID, I have found that much out - it is described as a 0+1 RAID set) and I want to set it up to work!
    All that happens at the moment, is that the SATA BIOS scans the channels for the RAID and does not find it. Then it goes on, saying that the BIOS is not installed.
    I am supposed to press Ctrl-F to go into the BIOS setup, but when I do this, it ignores me - have tried pressing from just after the POST and I have tried resetting the BIOS, to no avail!
    In the manual, it says that when you start the machine up first time, it will tell you to press Ctrl-F to go into the setup or Esc to continue. I cannot believe that you can ONLY setup the SATA once, at first startup?
    If it is ONLY at first startup, then when is the definition of "first startup"? I have tried all things to reset the motherboard and they do not work:
    1. Shutting down the machine
    2. Removing the power supply connectors
    3. Reset the BIOS w/J11
    4. Removing the backup battery
    5. Removing the backup battery and resetting the BIOS w/J11
    6. Removing memory
    7. Removing drive cables
    8. Reflashing the BIOS
    Anyone got any other ideas?
    Thank you all, in advance.
    Leni

    Thanks for the help, guys...
    The RAID setup was OK. I was advised to backup all the data on the drive before doing this, which I did. I just used "Auto" to include this drive as an ordinary drive on IDE 3. After, I had a look at the drive and nothing seemed to be different. I have used a RAID card (it was cheap) - HPT370 - as an ordinary IDE card and that was a bit simpler. The HPT370 just scans and finds the required drives and they are there.
    Incidentally, I did look at the diag's on the top of the drive and I do not remember it saying anything about differences between Master and Single drives. No harm done(except losing 4 hours of MY LIFE)!
    Incidentally, drunken_rice I am not using the RAID as a bootup drive. Although I did not lose any data myself, I would suggest that you backup your data before adding your drive into the RAID (I was advised of this before) - just in case!
    Regards,
    Leni

  • Replacement Chipset/Heatsink Fan (northbridge? for k7n2 delta-ilsr)

       < i need a replacement heatsink and fan for this fan.  that will fit!          Reason: I want a new one that is quiter, and the original fan in it broke.  I also need to be able to buy these part(s) online.

    Me too. You can get them in copper or aluminium. I have the latter, and for more than year now it's been doing a fine job with minimum noise.
    Check it out here:
    http://www.pcabusers.com/reviews/iceberg/p1.html

  • G4Ti4200-VTD64 voltage incompatibility with MSI K7N2 Delta-ILSR??

    Hello,
        I have the MSI G4Ti4200-VTD64 (4X) video card..  I want to upgrade my motherboard to K7N2 Delta-ILSR. Is there any voltage incompatibility?? I heard that new mother boards will support only AGP 1.5V. Is the AGP voltage of K7N2 Delta-ILSR 1.5volts??  Is my video card compatible with this voltage?? I really want to retain my current video card as I am quite satisfied with it and I'm not willing to invest on a new one at the moment. If there is an incompatibility could you suggest another Socket A MB with good performance and SATA RAID support.
    Thanks in advance
    Regards,
    Joseph

    Joseph,
    All 4X Vid Cards work on all 4X and 8X mobos. All 4X mobos work with all 4X and 8X Vid Cards.
    Take Care,
    Richard

  • VGA at PCI 3, not in AGP, Why?? (K7N2 Delta - ILSR/5600VTDR

    hi...
    When i enter to see the properties of my VGA card adapter, it is in the "PCI 3"bus, why doesn´t it in AGP bus ??
    i downloaded the "DMI info", the PCI 3 is "in use" and the AGP is "available".
    Is there something wrong ??
    my configuration is:
    K7N2 Delta - ILSR
    MSI GeForce FX5600VTDR 128Mb
    512Mb DDR
    Athlon 2.4 tb

    Have gone into your bios and adjusted your chipset settings?  If not you need to change a few things first of all your default settings for vga are set for PCI so you'll need to change that to AGP.   Second your memory usage will need to get upped from 64 mb to 128mb.   Next you'll want to enable 8x speed and fastwrites these will increase video quality.

  • K7N2 Delta-ILSR Agp conflicts

    hi all
    just regestard NEW BEE
    just got k7n2 delta-ilsr
    got all set up BUT, i had to use old graphics card to install Xp pro then put my primary graphics card in (phrophet 4500 64mb) in started up system and in devices of motherboard the pci to agp recources were all full up and dont work so the graphics card doesnt work, any ideas ??????
    ps I'll have to get uptodate driver for graphics card.

    Hi,
    Killy your score's not bad at all!   I'm more used to 3D Mark2001SE scores but yours seem very reasonable. I get about 1,600 on 3DMark03 and I run most recent (3D games) without problem (a little slowing down here and there) but your score is nearly 3 times mine! - Quite respectable!  
    Axel  

Maybe you are looking for

  • Number of columns in query form

    I have an <af:query> component from a View Criteria. In the design it says "No search fields added." I have 10 query fields. I want to display 3 columns, with 4,2,4 fields respectively. If I set the property "Rows" to 3, it displays 4,4,2 fields in t

  • My iPod bricked itself

    Hi, I installed the 2.0 firmware for the iPod Touch, and it seemed to work fine. Then the next time I synced with iTunes all the apps would just like start up but it would only display the loading screens, not the acutal app. Like it was frozen, none

  • Block alignment for NetWare 6.5 Virtual Machines

    I have an enviornment with multiple virtualized Netware VM's running on vSphere. Some were converted using VMware's P2V software other's were migrated using the SCMT. My question relates to block alignment at the NSS layer. I have the block alignment

  • Call to Jasper Report from a jsf only? Or can v use a jsff page?.

    Hi, I am new to JDev and ADF. I have a application using ADF . I have created Jasper reports as well and trying to  Integrate the Reports . If i make a call to the Jasper Report with a small dummy application it works. But if i do the same from withi

  • Where are my movies stored?

    Where do my movies from my iphone get stored on my Mac when they are imported into iPhoto?  That is, where do the actual files get stored?