Inspection plan issue

Hi Gurus,
I have created a inpection plan in plant 1000 and this material is extended to 1100 and 3000 plants.
So in QA32 transaction code i see a plant 3000 coming uo automatically, even though i have created inspection plan with workbench in 1000 plant.
I was checking the table QAVE with the inspection lot number and 1000 plant combination, and its giving no data available. I.e this inpection lot is stored in 3000 plant.
When  i am checking the inspection lot in QA03 tcode, plant assigned to that is 1000.
Please advise where i am doing mistake.
Thanks in Advance
Quantum.

Hello Quantum,
first of all in which plant is the inspection lot created?
-> The inspection lot is assigned to the correspondent plant
(If you want to avoid this you would have to create the inspection lots in the same plant in which the plans are maintained)
The selected set always correspponds with the plant in the inspection lot.
Example: -> I create a GI in plant A and have assigned a plan from plant B
                  The inspection lot is assigned to plant A
                  In the UD the selected set is used from plant A
This is standard behaviour. If you want to change this behavior I'm afraid that is hardly possible.
What I don't understand is why it is so important to keep the selected set in the same plant as the plan?
Regards,
Isabelle

Similar Messages

  • Inspection Plan - Change order date Combination issue

    We are facing 1 issue in our system.
    The Inspection plan assignments with new change orders is not assigning the correct inspection plan.
    Example:
    Plan                       Change Number               Valid from Date
    1                              CO-1                                1/01/2007
    2                              CO-2                                1/01/2008
    3                              CO-3                                1/01/2010
    The plan selected when Change order CO-2 is cut in, is plan 1 but should be Plan 2. We believe the date on the CO does not drive the selection of the most current plan. When plan 3 is implemented after plan 2, Plan 2 is selected.
    Any one has faced this kind of issue in your exp?
    Edited by: Tom_Eric on Apr 28, 2010 10:49 PM

    No reply

  • How to block deletion of Inspection Plan

    Dear Experts
    Accicendatally, our users are deleting the Inspection Plan,
    Is there any authorisation object to make Restriction on this,Transaction is QP02.
    Regards
    Sandeep patil

    Hi Sandeep,
    As you said User's are deleting inspection plans. They must be putting it for deletions by clicking on deletion flags.
    If you want to restrict this then you have to get help of security team. They will find role for this transaction -
    > then they will find out the objects matanined in this role -
    > this will display all the activities in that object -
    > then they can cancel deletion activity from object list.
    Then when User will access QP02 then this checkbox will appear grey. Then they will not be able to delete inspection plan.
    Hope this resolves your issue, reward points if helpful.
    Regards,
    Avinash.

  • Master data changes not updated in Inspection Plan- QP01

    Hi
    We created all the QM master data . After that we did some changes in inspection chars and in the sampling master data.but the values are not reflecting in the Inspection plan . How to update the changes in the inspection plan. We are trying to find indIvidual as well as Mass update
    Any input will he highly appreciated
    Thanks
    JJ

    Dear JJ
    Another easy method will be maintaining MIC as referenced mic. instead of maintaining it as complete copy model you can make it referenced. any changes in the mic can be updated automaticalyin the inspection plan using the referenced functionality.
    The issue being wherever the mic goes will be changed,
    Regards
    gajesh

  • Measuring Instrument Needs to be added in inspection plan for each part

    Hi
    How to assign the Measuring Instrument in the quality inspection plan for all the materials.
    Whether i need to assign as material assignment or as PRT.
    how to use prt to assign to the operation in the quality plan (task list)
    Thanks
    VRAJ

    Hi,
    when i try to assign the Equipment for first Inspection Characteristics.
    the system thru the ERROR as,
    Production resource/tool is not intended for this type of task list
    Message no. CF230
    Diagnosis
    You want to use the production resource/tool in a task list or work order with task list type Q. However, according to usage 004 of the PRT, this task list type does not exist.
    Procedure
    Change the usage of the PRT in the master record or select a PRT which can be used in this task list type.
    How to resolve this issue.

  • Inspection plan creation

    hi all,
    i am creating inspection plan using bapi 'BAPI_INSPECTIONPLAN_CREATE' . it is creating but the issue is in table 'INSPCHARACTERISTIC' there is a field 'SEL_SET1' which is getting populated automatically in transaction and i want that value to be replaced by the one i am passing in table
    'INSPCHARACTERISTIC' but it is not happening.
    Is thers any specific way to get it done through this bapi or is there any exit or badi to perform this task?
    Any pointer will be highly appreciated.
    regards
    vijay

    Yes, I have seen that field.
    You can enter a value for this field only if it is Qualitative characteristic.
    So while populating Qualitative or quantitative indicator values for
    IF INSPCHARACTERISTIC-QUANTITATIVE_IND = 'X'
    INSPCHARACTERISTIC-SEL_SET1 = 'Your value'
    ENDIF.
    If it's Quantitative Do not even pass any value for this field. Not even space.
    In debuggin you can check the INSPCHARACTERISTIC-SEL-SET1 value. It will have the value you passed.
    When I worked on it I remember that there are a whole lot of indicators which are specific to Quantitative or Qualitative. You will have to split the code for them to pass the values separately.
    Note: All the above can happen only if the SEL_SET1 is not defaulted to have a value in configuration.
    Thanks.

  • INSPECTION PLAN ALE SETTINGS

    Hi ,
    Its a Migration Project and we have to Transfer all the Inspection Plans from the Old System to a New System.
    We are tryin to go by the Idocs Approcach.
    But i donnt know the MASS SEND Prog. for the same eg. BD10(RBDSEMAT) for Material , also i am stuck in the ALE Settings too ...
    In Outbound Side Distribution Model i have added the following BAPI :
    Object name        InspectionPlan
    Method name       Create
    Object type          BUS1191
    Method                CREATE
    Description          Create inspection plan
    and in the Outbound Partner Profile :
    Message Type INSPECTIONPLAN_CREATE
    Basic type        INSPECTIONPLAN_CREATE02
    I am also not able to Find the Inbound Process Code for the message type INSPECTIONPLAN_CREATE.
    Although i guess the Inbound Function Module is IDOC_INPUT_INSPECTIONPLAN_CREA .
    Please help me with the issue.
    regards
    Vikas.

    Thanks... but i am still in need of a mass send program ... or can i send the inspection plans via change pointers ?
    while creating the entries in BD52 (Change Document Items for Message Type) i am not sure what should be added for this message type (INSPECTIONPLAN_CREATE)?

  • QM- delete inspection Plan

    Hi Guys,
    i have an issue regarding master data and inspection plan.
    i need to change the base unit of measure on a material.
    when i tried the system gave me this message:
    The base unit of measure cannot be changed.
    The reasons for this are:
    Routings already exist that are assigned to the material.
    Type Group    GrC Plnt
    Q    235723   1   USNA
    so i have checked table PLKO and found my material.
    i have seen that an Inspection Plan has been created, so i deleted the IP with QP02. went to MM02 tried to change the Bum but same error.
    run tcode QSR6 but i am not able to delete this I.Plan. am i missing something?
    can you please help?
    thanks
    C.

    BTW: for your process you don't need to delete the inspection plan.  All you need to do is go to the material assignment screen at the header level of the insp. plan and delete the assignment of the material to the plan.  Then, if you wanted to, after changing the BUOM in the material, you could use QP02 to change the UOM used in the inspection plan, and the reassign the material back to it.  Save you from having to recreate the plan.
    FF

  • Re assignment of material from inspection plan group

    Dear Experts,
    I have an issue, we got a material which has multiple groups assigned to it.
    How to remove the materials assignment from the inspection plan group?
    Since the group contains more than 1000 line items, it is very laborious to search every line item and delete manually.
    Is there any 1 shot way to remove the assignment?
    Please help me out in this, because of multiple assignment, the lot gets into the status of CRTD.
    Thanks in advance,
    Anitha Pauline.

    hi,
    Use CWBQM.
    Regards

  • Inspection Plan & MIC status.

    Dear SAP,
    We have a requirement that QC will creat the MIC & Inspection Plan in status created, and QA will review and change the status from Created to Release.So where or in which object level i can put control so that QC not able to select the Status 4 for inspection plan, and Release for MIC.
    Regards,
    Asif.

    Dear Craig,
    I have created a new roll will basis help.and attached the below condition in the object you can refer dow.But then to user able to create MIC & Inspection plan in release mode.Please explain what would be the issue.
    MIC Status Table & Field Name (Object Name-Q_STA_QPMK,Table-QPMK, Field-LOEKZ)
    Inspection Plan Status Table & Field Name (Object Name-Q_ROUT,Table-PLKPO, Field-VERWE)
    QSTATMERK Master Inspection Characteristic Status 1
    STATU  Status  1
    Regards,
    Asif

  • Inter-company Inspection plan

    Hello
    Need your advice in SME Please. We have two company code. We are planning to use one Plant Master inspection charat for the next plant in the Inspection plan . Means same group and same group counter will be used for both the material in the Material assignment tab  with different plant assignment .Any one experienced this type of business requirement.
    What is the pros and cons ?. Any input will be highly appreciated
    Thanks,
    Nic

    Yes, when you use the plan across company codes you can get that message.
    I've never run into any issues however by sharing the plans.  But I beleive the error from SAP is due to costing.  Since you can use the plans, operations and workcenters to collect costs, I beleive that is where you might have trouble with going across company codes.  As long as you aren't tracking costs in your plans, you shouldn't have a problem.
    The only issue you can have is if a person in plant A wants to change the shared plan created in plant B.  the must be given securityfor plant B.  You can create all the plans in a central, non-manufacturing or virtual plant, (like you should do for MIC's) and give lab managers/supervisors security to that plant.   Or just create them any plant and give the right users access to that plant. 
    FF

  • Control Indicators in inspection plan

    Hi QM Experts,
    I created MICs and assigned the selected set and assigned the control indicators. But when i create the inspection plan for the material and assign the MIC, system is not copying the control indicators from MIC.
    This is happening only in the production client. In the quality client, system works fine and copies the control indicators maintained in MIC to inspection plan.
    I checked all the configurations but could not find anything related.
    Can anybody help?
    Thanks & Regards
    Prathib

    Dear Prathib
    It doesnu2019t matter whether it is complete or incomplete MIC as far as copying of control indicators from MIC to inspection plan is concerned.
    If you are dealing with incomplete MIC, then at the time of inspection plan creation you need to specify lower, upper, target values, may be decimal places and selected set in case of qualitative MIC.
    Control indicators mean the various ticks that you choose while creating MIC in QS21, for example, Lower, Upper, Target values tick, fixed scope, or required, optional characteristic etc.
    I think system will never behave contradictorily in quality and production server because itu2019s certainly not a customizing issue.
    What I would suggest is, note down what control indicators you have chosen for MIC in QS24.
    While creating inspection plan, use this MIC. If itu2019s incomplete give necessary information and proceed. Select the entire MIC line and click on control indicator tab. Note down what indicators it shows.
    I am sure would be same.
    Regards,
    Anand Rao

  • Fetching the Inspection plan from OEM/owning Plant while doing GR in MIGO

    Hi,
    I have a scenario-
    a) I am doing a Goods Recipt against a purchase order for a plant(suppose Plant A).
    b) I have to fetch the Inspection Plan from the Owning OEM(suppose Plant B) of the material.
    At present we are maintaining the inspection plan for Plant A & B separately, which is not in synchronization.
    Can anyone suggest any BADI or user exit that can be enhanced to deal with this scenario?
    Thanks in Advance.
    Priyabrata

    continuing my issue is it possible to that we donot have to change the gbb and vbr and still we can have the desired results.
    that is we are able to use different gl for debit while doing goods issue from a single stocked material
    or we want to have this result
    1.          repairs to p&m    1000    dr
                         stock of cement  a/c           1000    cr
    2.          repairs  to building    2000   dr
                          stock of cement  a/c            2000   cr.
    3.             construction     3500     dr
                                 stock  of cement     3500     cr
    we donot want to change the GBB and VBR every time    or change the GL a/c while doing reservation.
    is there any third option where we get the desired result without changing or entering the g/l manually
    if there is please let me know the t.codes

  • LSMW for Quality Inspection Plan

    Dear All,
    I am in process of uploading Quality Inspection Plans through process of LSMW with standard object 0240 (Inspection Plans) with batch input method. With this when I am trying to create Batch Input Session, system is throwing me error as 'Characteristics is not yet created' (Message Number - QS 320). I have maintained all the relevant master data before going to upload Q Inspection Plan.
    Could any one pl. throw light on this issue?
    Regards,
    Prashant

    Depending on what control indicator key for master inspection characteristics have you implemented in the operations within the plan, the system checks if the characteristics are completely maintained.
    This has nothing to do with LSMW, it's just a normal message,.....what I find estrange is that the message you're saying is a warning message not an ERROR message.

  • Inspection plan assignment

    Iu2019m facing an issue when creating inspection lots.
    I have one task list group with 3 counters inside.
    Counter 1     Material A / Plant A / Customer A;
    Counter 2     Material A / Plant A / Customer B;
    Counter 3     Material A / Plant A / Customer C.
    When I create these inspection lot through of transaction QA01, the system is assigning  the  inspection plan properly to each one of these combinations.
    If the creation is done through a delivery the system doesnu2019t assign any inspection plan.
    Somebody can help me?

    The inspection lot origin that I'm  using is 02
    I created 2 inspection plans to  2 differents customers.
    I also created 2 delivery process with 2 differents customers and the Inspection Lot was created after the Goods issue in the delivery process, but the Status is CRTD.
    As I believed that it was wrong, then I tried to create new inspection lots through the transaction QA01 to each one of this customers, with lot origin 02 to check the system behaviour.
    At this test the system assigned properly the inspection plan to the inspection lot.
    I read the explanation of marwadi, and I understood that can't assign inspection plans at the Customer level.
    Can you check if is it OK?
    Thank you
    Tiago

Maybe you are looking for

  • Any ideas for this situation?

    I have a application which allows users to enter information about a file and stores the information in an XML file of the same name. So, if I had a file at d:\myFolder\myFile.ext it would create the following xml file d:\myFolder\myFile.ext.xml As y

  • Shared Review: Acrobat Pro 9; Reader 8 issues

    Hi, I've been experimenting with the Shared Review features on Acrobat 9 Pro, and we've run into some slightly odd behaivour. I created a PDF file, sent it for a shared review, and waited for the comments. All three reviewers started with Reader 8, r

  • Photoshop & InDesign CS3 Crashing when Saving to Network

    Hi, Photoshop & InDesign CS3 crashes whenever I try to save a file over the network to a shared computer we are using as a server. SPECIFICS I'm running Leopard 10.5.2 - I have tried reinstalling the entire Creative Suite - I did not reinstall Versio

  • Mail not coming with information broadcasting scheduling

    dear all, when i execute directly the setting for information broadcasting a mail is being sent but when i schedule the same setting in transaction SOST it is showing warning 'waiting for communication service'.how to remove that. ajay

  • How to store molecular formula in MM (eg:H2O)

    How to store/tie molecular formula in MM (eg:H2O)