N8 - battery probably empty - does not start

Hello.
My N8 battery probably got empty during the night cause in the morning I found it switched off. I started to charge it but the phone does not start anymore. The little light blinks for a while and afterwards stops. I charged it for 2 hours and still it does nothing if I press switch on button. The screen is blank, no indication that it is in the charger.
Thank you for any advises.

If you've tried all the suggestions already made and still nothing, you'll find the problem is in the phone itself... I had a similar problem a little while back and took it to Nokia Service Centre for them to have a look and it turned out the phone was faulty and they replaced it for me... Too bad I hadn't made a back-up and lost everything... Good luck

Similar Messages

IPhone 3gs Battery Heating, iPhone does not start even after the battery replaced

Hello
Last night my phone was plugged into the car charger and suddenly it went blank and turnned off itself. I Tried DFU'in it but nothing worked. I charged it but all it does is heats up. Today I replaced the battery and it sill wouldnt work. I cant turn it on at all!
Can some one please help me.
URGENT!!
Thanks

Extremely doubtful. Without being able to get the phone up and running, it's impossible to say for sure, but I'm guessing any data that was on the phone is long gone.
As for what could be the issue... at this stage, I'll have to go with an all encompassing "it's broke". You're probably going to either have to find a professional repair shop or just buy a new phone. Apple won't touch it at this stage since you opened it yourself.

My battery still does not start recharging when less then 10% charged

Hi,
I have been having problem with my laptop (Pavilion dv7) for the last three weeks if not more. Basically the battery does not start charging when it is less then 10% charged. I tried calibrating the battery and the problem seemed to disapear for some time. However after less then a week it starting doing the same thing again.
When I try the battery healt teset (that comes by default with the laptop) it gives me a message that battery should be replaced and also gives me the warrenthy id. Should I go with the warrenthy id to the place where I bought the laptop to get a new one? Or is there anything else I can do to try and solve the problem.
Regards
Simon J.

Call up HP Tech Support, provide them the warranty ID, to get your battery replaced...Given if your Laptop is not more than 1 yr old, as Battery has one 1 Yr warranty on it...
Although I am an HP employee, I am speaking for myself and not for HP.
Make it easier for other people to find solutions, by marking my answer with 'Accept as Solution', if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

T400 does not start up with a battery and AC, but starts up with only AC.

I bought T400, 7417-CTO in Jan 2010. My T400 does not start up with a battery and AC power. I tried to start with only AC power after pulling out the battery, it worked fine. Even when I inserted the battery in T400, which was running perfectly with AC only, T400 seems to lose the power - more strictly speaking, it kept stoping and re-running several times, and finally it dead.
a few possibilities
1) a battery is dead - but it does not explain the failure with both AC and battery
2) some hibernation issue - I plugged in and out the DIMM, and clock battery. I tried to keep pushing the power button trick, but it didn't work
3) Mother board failure??
I really appreciate if you give me some advice on it.
Wanyong

Thanks for all your kind and helpful comments.
Unfortunately, I don't have any friends who have Lenovo - or I don't have many friends here since I moved in the last summer. ;-)
After purchasing a new battery, I will update it. Hope that this thread helps someone who had/will have same prob. as mine.
-WS

Last night my ipod touch(with iOS 5 beta 4) tried to reboot itself and is just not starting. it does not allow me to do anything and does not start till it's battery is exhausted. iTunes is not recognizing it. pls hlp............!!!!!!!!!!

Last night my ipod touch(with iOS 5 beta 4) tried to reboot itself and is just not starting. it does not allow me to do anything and does not start till it's battery is exhausted. iTunes is not recognizing it. pls hlp............!!!!!!!!!!

Please post in the developer forum using your account credentials.
Stedman

My iMac does not start.

My iMac does not start. When I turn it on, it stays loading in the half and doesn't continue. Some days before I had updated my iMac to Yosemite 10.10. Everything was ok but yesterday I decided tu reboot it and when it was turning on this happened, it kept stuck at the middle of the bar. I have the latest model of MacBook Air '13.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My iPad does not start. What can be the problem

My iPad does not start. What can be the problem

Does anything happens when you try to switch it on ? If not, then assuming that the battery isn't empty (and it can take up to 15 minutes of charging before it will respond), then have you tried a reset ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Macbook does not start

Greetings. This is my issue:
I don't know why the macbook does not restart, if you try to restart it, it comes to black screen and i had to press the power button twice (Turn it absolutely off and turn it up), i took it to an apple authorized service center and he put an external HDD and restart it from this HDD then restart my macbook and it restarted normally, a few days later the problem persist.
Now the big deal: I turned it on, open safari and immediately it comes black screen and the status white led start blinking, i press the power button and stop blinking and press it again but it does not start, the blinking comes again... I left it off for an hour or so.
One hour later it boots normally but in few seconds it freezes and becomes a message in the screen that reads: " You need to restart your computer. Hold down the Power button for several seconds or press the Restart button". Then i press the power button, when i tried to restart it again there came a lot of strange stripes in the screen, gray and black with some color dots, a very weird thing, the "Start up chime" sounds about tree times and the stripes keep changing, always stripes. I restart it again, and the same thing happens one more time, and the third time i restart it it does not show anything on screen, all black and no sound, i tried putting out battery and everything Apple says to do when macbook does not boot, but nothing happens... i press the power button the sound of the HDD (I guess) that always sound, i can hear it, and the status white led is on, but not blinking, but nothing else....
what should it be?
it is a late 2007 macbook and out of warranty, does not have apple care.

This is what the last Kernel Report says:
Thu Jul 23 09:27:51 2009
panic(cpu 0 caller 0x00195080): "pmapremoverange empty hash removing hashed pv"@/SourceCache/xnu/xnu-1228.12.14/osfmk/i386/pmap.c:2072
Backtrace (CPU 0), Frame : Return Address (4 potential args on stack)
0x2107fbf8 : 0x12b4c6 (0x45ec20 0x2107fc2c 0x13355c 0x0)
0x2107fc48 : 0x195080 (0x4651d0 0x32cfab0 0x4e33c80c 0x10000)
0x2107fcf8 : 0x1972db (0x32cfa6c 0x1000 0x0 0x105e008)
0x2107fd58 : 0x16abc5 (0x32cfa6c 0x1000 0x0 0x2000)
0x2107fe78 : 0x16b18d (0xffe00000 0x0 0x0 0x0)
0x2107feb8 : 0x13bb81 (0x32b9aa8 0x0 0x0 0xffe00000)
0x2107ff08 : 0x376f2a (0x29b770c 0x0 0x2107ff58 0x19c6b3)
0x2107ff58 : 0x376f58 (0x2c8be44 0x0 0x3169404 0x0)
0x2107ff78 : 0x3e2e3b (0x2c8be44 0x31693c0 0x3169404 0x1213)
0x2107ffc8 : 0x1a1bfa (0x3165520 0x0 0x1a40b5 0x3174208)
No mapping exists for frame pointer
Backtrace terminated-invalid frame pointer 0xbffffee8
BSD process name corresponding to current thread: scsid
Mac OS version:
9J61
Kernel version:
Darwin Kernel Version 9.7.0: Tue Mar 31 22:52:17 PDT 2009; root:xnu-1228.12.14~1/RELEASE_I386
System model name: MacBook2,1 (Mac-F4208CA9)
System uptime in nanoseconds: 18167463710
unloaded kexts:
(none)
loaded kexts:
com.apple.driver.InternalModemSupport 2.4.0 - last loaded 17433441031
com.apple.iokit.IOBluetoothSerialManager 2.1.6f8
com.apple.driver.AppleUpstreamUserClient 2.7.5
com.apple.driver.AppleHDAPlatformDriver 1.6.8a3
com.apple.driver.AppleHDA 1.6.8a3
com.apple.DontSteal_Mac_OSX 6.0.3
com.apple.iokit.IOFireWireIP 1.7.7
com.apple.driver.AppleGraphicsControl 2.8.11
com.apple.driver.AppleIntelGMAX3100 5.4.4
com.apple.driver.AppleIntelGMA950 5.4.4
com.apple.driver.AirPort.Atheros 319.10.3
com.apple.driver.AppleHDAController 1.6.8a3
com.apple.driver.SMCMotionSensor 2.1.1d2
com.apple.driver.AppleIRController 110
com.apple.driver.AudioIPCDriver 1.0.6
com.apple.driver.ACPISMCPlatformPlugin 3.4.0d10
com.apple.driver.AppleLPC 1.2.12
com.apple.driver.AppleBacklight 1.6.0
com.apple.driver.AppleTyMCEDriver 1.0.0d28
com.apple.driver.AppleIntelIntegratedFramebuffer 5.4.4
com.apple.driver.CSRUSBBluetoothHCIController 2.1.6f8
com.apple.driver.AppleUSBMergeNub 3.4.3
com.apple.driver.CSRHIDTransitionDriver 2.1.6f8
com.apple.driver.AppleUSBTrackpad 1.7.4f1
com.apple.driver.AppleUSBTCKeyEventDriver 1.7.4f1
com.apple.driver.AppleUSBTCKeyboard 1.7.4f1
com.apple.driver.XsanFilter 2.7.91
com.apple.iokit.IOAHCIBlockStorage 1.2.1
com.apple.driver.USBCameraFirmwareLoader 1.0.9
com.apple.iokit.IOSCSIMultimediaCommandsDevice 2.0.9
com.apple.iokit.SCSITaskUserClient 2.0.9
com.apple.iokit.IOATAPIProtocolTransport 1.5.2
com.apple.driver.AppleFileSystemDriver 1.1.0
com.apple.driver.AppleIntelPIIXATA 2.0.0
com.apple.driver.AppleFWOHCI 3.8.2
com.apple.driver.AppleAHCIPort 1.6.0
com.apple.driver.AppleUSBHub 3.4.0
com.apple.iokit.IOUSBUserClient 3.3.1
com.apple.driver.AppleUSBEHCI 3.4.3
com.apple.driver.AppleUSBUHCI 3.3.5
com.apple.iokit.AppleYukon2 3.1.12b14
com.apple.driver.AppleEFINVRAM 1.2.0
com.apple.driver.AppleSmartBatteryManager 158.10.0
com.apple.driver.AppleRTC 1.2.3
com.apple.driver.AppleHPET 1.4
com.apple.driver.AppleACPIPCI 1.2.4
com.apple.driver.AppleACPIButtons 1.2.4
com.apple.driver.AppleSMBIOS 1.4
com.apple.driver.AppleACPIEC 1.2.4
com.apple.driver.AppleAPIC 1.4
com.apple.security.seatbelt 107.12
com.apple.nke.applicationfirewall 1.6.77
com.apple.security.TMSafetyNet 3
com.apple.driver.AppleIntelCPUPowerManagement 76.0.0
com.apple.driver.DiskImages 199
com.apple.BootCache 30.4
com.apple.iokit.IOSerialFamily 9.4
com.apple.driver.DspFuncLib 1.6.8a3
com.apple.iokit.IO80211Family 216.1
com.apple.iokit.IOHDAFamily 1.6.8a3
com.apple.iokit.IOAudioFamily 1.6.9fc3
com.apple.kext.OSvKernDSPLib 1.1
com.apple.driver.IOPlatformPluginFamily 3.4.0d10
com.apple.driver.AppleSMC 2.2.1d2
com.apple.iokit.IONDRVSupport 1.7.3
com.apple.iokit.IOGraphicsFamily 1.7.3
com.apple.driver.AppleUSBBluetoothHCIController 2.1.6f8
com.apple.iokit.IOBluetoothFamily 2.1.6f8
com.apple.iokit.IOUSBHIDDriver 3.2.2
com.apple.driver.AppleUSBComposite 3.2.0
com.apple.iokit.IOSCSIBlockCommandsDevice 2.0.9
com.apple.iokit.IOBDStorageFamily 1.5
com.apple.iokit.IODVDStorageFamily 1.5
com.apple.iokit.IOCDStorageFamily 1.5
com.apple.iokit.IOSCSIArchitectureModelFamily 2.0.9
com.apple.iokit.IOATAFamily 2.0.1
com.apple.iokit.IOFireWireFamily 3.4.7
com.apple.iokit.IOAHCIFamily 1.5.0
com.apple.iokit.IOUSBFamily 3.4.3
com.apple.iokit.IONetworkingFamily 1.6.1
com.apple.driver.AppleEFIRuntime 1.2.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.iokit.IOStorageFamily 1.5.6
com.apple.iokit.IOHIDFamily 1.5.5
com.apple.driver.AppleACPIPlatform 1.2.4
com.apple.iokit.IOACPIFamily 1.2.0
com.apple.iokit.IOPCIFamily 2.6

I just returned from air travel with my macbook pro. It does not start up. Completely black, no sound, no life.

I just returned from air travel with my macbook pro. It does not start up. Completely black, no sound, no life. I tried command-option-power. Still dead.

SheilaArl wrote:
I just returned from air travel with my macbook pro. It does not start up. Completely black, no sound, no life. I tried command-option-power. Still dead.
I have a 2007 Macbook, so it's probably a lot older than your Macbook Pro, but it sounds like what happened to me, except that mine hadn't travelled anywhere. I pulled out the ram and blew out some dust, popped them back in, and wha-la! it turned back on and worked better than ever! Or otherwise you've got a dud/old/warped/fried battery, which is also what happened to my laptop - it got so bad it did what your laptop is doing. Ordered a new battery online and all good since then. Or otherwise, like the previous post asked, 'is it plugged in?'

Can not update tiger and safari does not start

Hi everybody,
I have actually two but probably interrelated problems: First, safari does not start and second, I can not update tiger.
It all started a few days ago on my MacBook (Intel). Somehow, Safari produced an error (I only guess that it was Safari because I was downloading a movie clip) and Tiger was frozen. After rebooting, the whole system had problems (e.g., Safari and Skype were not starting). I tried to reinstall and archive mac os x but with no success. The problems were growing actually even worse (e.g., slow) and at some point in time, Tiger was not even starting. Thus, I did a full new installation of 10.4.8 (delete and install). Afterwards, it worked first but after the automatic software update, the system told me that their was an input/output error (???) during the 10.4.10 update. Afterwards, the whole system had again problems (slow and problems with even booting)!! Thus, the software update made it even worse. So, I did again a full installation (delete and install).
I have to update my 10.4.8 system, because I also have iLife08 that needs at least 10.4.9. However, I don't know what to do to avoid again these update problems??
In addition, despite the full installation, Safari is not starting. Thus, there is still some problems but I have now clue where this comes from as it is newly installed?!
Any ideas?? Thanks...
Crobus

Crobus, welcome, since you are starting from scratch with each re-install why not try Kappy's Extended Hard Drive Preparation.
http://discussions.apple.com/thread.jspa?messageID=5203987&#5203987
Do all steps from 1 thru 6, it is by far a more maintenance oriented than an Erase and Install. After the preparation, install OS 10 from your DVD, then download the OS 10.4.10 Combo Updater.
Joe

Premiere Elements 12 does not start after error message: display driver is incompatible

After successful installation and starting Premiere Elements the following error message appears: "Uncompatible display driver identified. Update the display driver for a better and faster playback performance!" Hopefully my translation from German is helpful enough. I confirmed with OK but unfortunately Premiere Elements does not start. I checked the display driver: it is the most actual one: AMD Radeon HD 7610M. Furthermore the hardware should be OK as well: ASUStek with an Intel Core i5-2450M CPU @2.5 GHz; 6 GB RAM; 64 Bit Windows 7 Service Pack 1. What can I do?

Moonkeys25
Recap...please confirm that as of this date, the problem exists with or without the antivirus and firewall(s) disabled.
Moving forward...
If you issue was specific to the display card error that you have been getting then probable conclusions
a. the ADM Radeon H7610M driver version is not up to date
or
b. the ADM Radeon H7610 M video card/graphics card installed as is is not compatible with Premiere Elements 12 on your Windows 7 SP1 64 bit
The updated driver version and the BadDrivers.txt file deletion should have corrected the problem unless there is a gross mismatch between Premiere Elements 12 and ADM Radeon H7610M.
Did you use the link that John posted to get the auto detection of the latest driver version for the ADM card?
If we have gone as far as we can with the card and its driver version angle on this, then we can try the generalized troubleshooting drills with no guarantees, just hopes
1. Delete the Adobe Premiere Elements Prefs file and, if necessary, the whole 12.0 Folder in which the Adobe Premiere Elements Prefs file exists.
Local Disk C
Users
Owner
AppData
Roaming
Adobe
Premiere Elements
12.0
and in the 12.0 Folder is the Adobe Premiere Elements Prefs file that you delete. If that does not work, then you delete the whole 12.0 Folder in which the Adobe Premiere Elements Prefs file exists. You just need to make sure to have the computer's Folder Option Show Hidden Files, Folders, and Drives active so that you can see the complete path cited.
2. If "1" has no effect on the issue...uninstall, ccleaner run through time, reinstall with antivirus and firewalls turned off.
a. Control Panel/Program, select Adobe Premiere Elements 12, right click the entry and click on the Uninstall pop up. Then follow the instructions for the uninstall.
b. Download and install the free ccleaner for a computer run through to get rid of leftovers from incomplete uninstalls and installs.
https://www.piriform.com/ccleaner/download
When you are ready for this step, I will give you a step by step through the ccleaner (regular cleaning part and registry cleaning part).
c. Reinstall from your installation files or installation disc, with antivirus and firewall(s) disabled.
Please review above and then let me know if I have interpreted correctly where we are in the troubleshooting. Do not start the above plan until we are in agreement on the details and hoped for results.
Thanks.
ATR

Microsoft Forefront Server Protection for Exchange Registration Service does not start automatically

Hello,
I am having an issue when I start my TMG 2010 machine:
(*TMG 2010 + Forefront protection for Exchange + Exchange Edge server role, acting like a SMTP relay and Antispam filter)
The service "Microsoft Forefront Server Protection for Exchange Registration Service"
does not start, it is set to "Manual".
I tried to find some information about which services should be started and which should not, but I cannot find such information, not even in Technet (my fault probably).
Thanks in advance.
Luis Olías Técnico/Admon Sistemas . Sevilla (España - Spain)

Hi,
Have you received any errors in event logs when
you started the Microsoft Forefront Server Protection for Exchange Registration Service?
Based on my research,
Microsoft Forefront Server Protection Controller service is a dependency of the Microsoft Forefront Server Protection Registration service and the Microsoft Forefront
Server Protection Registration service is a dependency of the Microsoft Exchange Transport service.
The Microsoft Forefront Server Protection Registration service normally only runs for a brief time (less than a minute) when FPE initializes. It then shuts
down and does not need to be running for transport scanning to occur.
You can refer to the link below:
Services
Best regards,
Susie

Integration Process does not start

Hi guru's
My scenario is this. From ECC we send Idocs to PI. We have an integration process to receive the idocs because only max 9999 are passed in the port.
We run just around 11000 CREMAS idocs now.
The problem is that the integration process does not start on our QA environment while it does start on DEV environment.
I've run many checks on both environments and they all look the same.
To name a few:
* Cache are all green and up-to-date.
* I checked the WF models which are behind the Integration Process and they are the same.
* Event correlation is correct in both environments
* When i test the idocs are correctly sent from ECC to PI.
However on DEV I see in transaction SXMB_MONI_BPE i see that the integration process is triggered and started. It waits 10 minutes and collects any messages that come in, and then bundles these and sends them on to the receiver.
On QA i do not see the Integration Process being started. Only records i see in SXMB_MONI_BPE are three work items, 2 completed, 1 ready, all 3 are called waiting for event.
I'm probably missing some configuration somewhere but what could it be?
Regards
Robert

Hi Eng Swee,
Thx. I checked it already and it works fine.
Meanwhile i did do some changes and some retests and now i saw somewhere that all my tests were creating more steps in an already started integration process, that was still waiting.
I now cleared some old workitems and started afresh.
What i see now is:
1) the BPM process start correctly
2) it receives 1 or 2 or 3 or n messages
3) it then waits for the deadline to finish, i.e. it should run for 10 minutes and then proceed to the next step which is sending the collected idocs to receiver.
On DEV the deadline works fine. On QA it doesn't.
IN SWU3 i have done the customizing and it shows green, so that part is OK.
Still the deadline is passed and it doesn't have the desired effect on mu BPM process (workflow).
Are there any other checks i can do to see if the deadline mechanism is properly working?
Is there a maybe a manual step i can do to trigger the deadline? Then at least i get some information on where the real problem is.
(Sorry for earlier confusion but i hadnt realized that there was still a process running)
Regards
Robert

Torch 9860 does not starts

help!
my blackberry Torch 9860 does not starts, and the red led blinking a slow time and 3 times faster
I removed the battery and waited, when i put the battery back, nothing happens
I installed the blackberry desktop, but it does not recognize the phone, not from any sign that is connected
I tested with another blackberry and connected everything right, the problem is not the cable or pc
when I connect it via USB the red LED blinks 1 time 3 times fast and slow
when I try to start it nothing happens

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain connected to a known-good wall charger (not PC USB):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain a known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Mail submission service on 2007 SP3 , does not start.

Hello,
I have two Exchange servers 2007 SP3 over Windows 2008 R2. One of them is a combination of the Client Access + Hub transport, and the other only holds the Mailbox role.
Whenever I start up the Mailbox server, the service "Mailbox submission service" does not run, even when it is set to be started automatically.
The two servers reach the Domain controller, they log on well, so, I suppose it is not a problem related to Active Directory.
I manually start the service and apparently it is okay, mails begin to flow normally.
I am reading issues related to Exchange 2010, about this very same service, but not regarding Exchange 2007 SP3.
Thanks in advance!
Luis Olías Técnico/Admon Sistemas . Sevilla (España - Spain)

Luis,
You wrote:
"I have restarted it again (lab environment, so, no impact ) [...]"
The same thing happens to me. One service or another does not start when I boot the test Exchange servers. I have to manually start them. Then everything works fine.
See what Ed Crowley wrote. If you shut down your test machines during periods of non-use, this is not unexpected.
As for the service logon (System Local Account), that is indeed the correct setting:
http://technet.microsoft.com/en-us/library/aa998342(v=exchg.80).aspx
That setting is not something that is normally changed and I don't think changing it would improve matters (it would probably break things).
If you look at the link above, you'll see that the mail submission service is dependent on the Active Directory Topology service. So if that service has not finished starting (has not finished querying Active Directory for the information it needs),
possibly because the CPU on the server is busy performing other startup operations, then it would not matter what the logon account is.
In other words, changing the logon account for the mail submission service will not make the AD Topology service start faster. And the mail submission service cannot start until the AD Topology service does.
Please mark as helpful if you find my contribution useful or as an answer if it does answer your question. That will encourage me - and others - to take time out to help you.

N8 - battery probably empty - does not start

Similar Messages

Maybe you are looking for