Quality scores updation
Hi Gurus ,
Can anybody tell me How quality scores updates in system for a material or vendor . As per my knoweledge Scores update only by Usage decision codes . Is any othe thing from which score gets updated .
Suppose i make defects recording and based upon that i make a notificaton , then the defects wt i have activited in system , by determining that can quality score gets updated .
For quality scores we mention values in QS51 (selected sets). and we also mention values for Defects class also , my question is score which i maintained in Defects clases wt is effect of these score .
Thanks in advance .
Amit
Please go through this and come back with your question, where are you did the setting, did you do any settings, if so which level, pl let us know
Define Quality Score Procedure
In this step, you define the procedures for determining the quality score.
The quality score procedure is defined in the inspection setup for the material master at plant level. You can define a default value for this procedure in the inspection type.
Requirements
The following specification limits have been defined in theSettings at Client Level.
Highest quality score
Lowest quality score
Lower limit for good quality
If you want to use quality score procedures that access the weighted shares of defects for the characteristics, you must maintain the characteristic weights.
If you want to use quality score procedures that access the quality score of the characteristics, you must maintain thedefect classes.
If you want to use quality score procedures, in which the system calculates the share of scrap, you must:
Check whether procedures for estimating the scap share have been defined inCustomizing
Assign suitable procedures for estimating the scrap share to the characteristics in the task list
Identify inspection characteristics as relevant for scrap in theircontrol indicators
Standard Settings
A number of commonly used procedures for determining the quality score are implemented in the standard system:
Quality score from the usage decision
Quality score from the share of defects in the lot
Quality score from the shares of defects for the characteristics
From the maximum share of defects
From the weighted average share of defects
Quality score from the quality score of the characteristics
From the minimum (worst) quality score
From the weighted average quality score
The table has the delivery class G. The following name range is reserved for the user
Quality score procedure 9, A, ... , Z*
Recommendation
Use the procedure in the standard system.
Decide on certain procedures for each inspection type; if possible, do not differentiate according to material groups or plants.
Activities
1. Determine which procedures for calculating the quality score should be used. You can make a distinction on the basis of the:
---Plant
---Inspection type
2. Modify the table of quality score procedures according to your needs. If the procedures contained in the standard system are not sufficient, you must create additional procedures using function modules.
3. Define the quality score procedures in the Default Values for the Inspection Type or in the inspection setup for the material.
Similar Messages
-
Hi,
I have been receiving quality scores of 0 in my keyword performance report. The quality score range mentioned in docs is 1-10. Is this zero quality score currently given only for non-US markets? Does this zero quality score means my ad wasn't long enough to
generate data?
http://advertise.bingads.microsoft.com/en-us/help-topic/how-to/50813/quality-score-in-depth
Thanks
VigneshHi Vignesh.
Prior to last month's Quality Score updates, even keywords in the US could get zero (blank) Quality Score.
In the past, your quality score would be "-" because your ad wasn't active long enough to generate data. Now even if
your ad has not been active for 30 days, we generate a quality score based on marketplace data so you can take action to improve performance much faster. This is only available in the United States.
For more information, please see the
MSDN QualityScore definition:
Quality score is based on the last rolling 30 days for the owned and operated search traffic. A quality score can be
assigned without any impressions, in the case where a keyword bid did not win any auctions. Traffic for content and syndicated networks do not affect quality score. The value in the report will be blank if the score was not computed. This can occur if there
have been no impressions for the keyword for 30 days or more.
I hope this helps,
Eric -
Quality Score in Vendor Rating
Dear Sir/Mam
I want to know about quality score which comes in Usage decision,Now in our case when inspection lot is generated we have only one case if accepted the quality score is 100 and when rejected 1,but our requriment is we want different quality score,i maintained different score in selected set,my concern whether this quality score has impact on vendor evaluation score( for quality criteria),how it is calculated please guide.
Regards
Kunal
Edited by: kunal joshi on Mar 26, 2009 6:07 AMDear Kunal
Quality score are maintained for quantitative valuation of the quality of inspection lots against a vendor, material , customer
1) They have to be first maintained in the client level setting
SPRO > QM> Maintain settings at client level> You need to maintain the highest quality score (100) and lowest quality score (1) system doesnt take 0. also Lower limit for good quality (90)
2) it is maiinly used in the selected sets for usage decision
QS51/ 03 catalogs for each UD code you can give a Quality score. So while you are giving UD system picks up this score and update the same for inspection lot , material, vendor, customer as applicable.
You can give 100 as quality score for clean acceptance, 1 for complete rejection, may be 50 for partial acceptance etc.
for eg you can maintain your UD selected sets like this Code, Description and UD score
001 Clean Acceptance A Accepted (OK) 100
002 Accepted subject to Rework R Rejected (not OK) 50
003 Accepted with deviation R Rejected (not OK) 70
004 Accepted after segregation (Partial qty) R Rejected (not OK) 60
005 Rejected R Rejected (not OK) 1
006 Accepted subject to functional test A Accepted (OK) 100
007 UD Changed due to line rejection R Rejected (not OK) 30
008 UD changed due to problem at Customer R Rejected (not OK) 1
009 Subcontract return - ABB A Accepted (OK) 100
010 Auto UD for Skip Lot A Accepted (OK) 100 -
Quality Score for manual inspection lot
Dear All,
As per the UD codes selected during the UD, the quality score for the vendor is updated.
This happens for both of the following cases.
1) Lot generated during GRN
2) Lot created manually
Is there any requirement of updating the score for manual lots. Is it useful.
I am updating the score for the samples received from vendor. Then again updating the score after I receive the actual qty.
So vendor score is updated twice. Is it the correct process of giving score to vendor through UD.
Regards
RutaHi Ruta,
It is not correct to award the quality score for samples, samples you can handle separatly through manual lot generation, you can generate the lot using separate inspection type( may be 7 as vendor audit / samples) which does not have quality score assigned.
And for actual lots generated throgh GR against PO (01 insp type) you can assign the actual quality scores . Quality scores / rating using this process will be correct and realistic one.
Best Regards,
Shekhar -
Quality Score in Quality Management
Dear Friends,
Plesae help me to explore how the quality score in quality management is updated.
What are all the configuration required.
I have created selected sets & assigned quality score.
How the defect classes come into picture.
What is the use of assignment of score to defect classes.
How the vendor gets score fnally. From selected sets or from the defect classes or from the combination of the both.
Please clarify.
RegardsHi Anuradha,
Plesae help me to explore how the quality score in quality management is updated.
What are all the configuration required.
In QS51 >> select catalog 3 and plant >> select any selected set and click on selected set codes >>
different codes will be displayed along with valuation and quality score.
Scores which you maintain here are updated automatically when you give UD. You can define scores as per clients requirement ex . if lot is ok then 100, if rejected 1 , if accepted with deviation say 50 etc.
How the defect classes come into picture.
Defect class will not come in picture when you use catalog '3' i.e. for UD, defect class comes in picture in following cases :
1) QS41 >> catalog 9, while defining the defect types you have to assign class i.e. type of defect Major, minor or surface defect this you can assign as per clients need.
2) QS51 >> Catalog 1, when you give valuation code you have to define defect class fr rejects.
What is the use of assignment of score to defect classes.
Where are you assigning score and defect class??
How the vendor gets score fnally. From selected sets or from the defect classes or from the combination of the both.
Vendor get score from selected sets, if there is defect in lot then you will give UD as rejected automatically vendor will get score 1.
Score is linked with UD directly and not with defect class. Considering the type of defect you will give UD and vendor score will update accordingly.
Please revert if any doubts.
Best Regards,
Shekhar -
Overall Quality score Main criterian?
Dear SAPIENTS,
In the T-code ME63 I can see Old score and New Score in my system. Now this New score is getting updated according to UD in QA11 but Old score is remaining 100 all the time. Can any one tell me how its getting calculated?
Regards,
Kaushal RaiHi
u2022 Goods Receipt (GR)
The goods receipt score is calculated from the quality score (QSc) for the inspection lots, according to the following formula:
QSc = (S1 + S2) / (n1 + n2)
S1 = Sum of quality scores for the inspection lots
n1 = Number of inspection lots
n2 = Number of deliveries for materials with a quality information record, for which no inspection lots exist.
S2 = n2 * QScmax
You can break down the GR score for the vendor according to the material and the inspection type.
Regards
Sujit -
Quality score by usage decision?
Dear SAPIENTS,
Can any one help me in creation of this configuration setting?
I would like to have quality score calculation from usage decision. Score calculation should be done by number of quantity received against order.
Suppose if 100 quantity ordered:
25% Deviation means 75 only received then score is 75
Likewise for 50%, 75% and 100%
Regards,Hi
please refer
Re: Quality Score in Vendor Rating
Regards'
Sujit -
Weighted from quality score of chars. with Inspection Lots
Dear QM Guru's.
My question is about Quality Score with Inspection Lots.
The Scenario:
1. In a Quality master View in Material Master I use the option number 05 of The Q-Score Procedure (Weighted from quality score of chars.)
2. I use Inspection Points.
3. I have 10 Inspection Points in a Characteristic.
4. When I make the Usage desicion, the Quality Score takes the last Inspeciton point.
The questions:
1. Why the Quality Score does take the last Inspection points, ?
2. Is there a chance The Quality Score taking the average of all inspection points ?
Thanks in advance.
FedericoThis procedure calculates the quality score as the weighted average of the characteristic scores.
The score for the characteristic is determined on the basis of the defect class score for the characteristic result. You define the weight of the characteristic in the inspection plan.
Sum ( E_KQD(characteristic) * WEIGHT )
E_KQD = ___________________________
Sum ( WEIGHT )
With E_KQD (charac.): Score for characteristic defect class.
If the defect class is blank or zero,
the result corresponds to the maximum
allowed score.
WEIGHTING: Weight of characteristic according to
inspection plan.
Now
As I understand It is Maximum allowed score which you have defined or the Avg one.
If you want to have the Avg of all inspection points then Copy & modify the function module KQD_COPY_REFERENCE_FORM ( originally KQD_FEATURE_CLASS_WEIGHTED ) -
Formula to calculate mean Quality Score
Hello!
What is the formula to calculate mean quality score?
Regards,
VMMeans quality score in broader prospect means
summation of quality score of number of inspection lots divided by the number of inspection lots...
for more Refer
Re: REGARDING VENDOR QUALITY RATING
http://www.sap-basis-abap.com/sapqm004.htm
Quality Score Calculation? -
Vendor blocking after particular quality score automatically
Hi Everybody
I hav following seniario
My client want to block the vendor for either creating purchase order or Goods receipt automatically after that particular vendor quality score reaches below certain level
After blocking the vendor he can release the vendor manully
Plz suggest
Regards
Ashutosh Shende
9860681314Hi,
You need to go with Enhacement-User Exit, This needs a code to be place which will check the score and if it below the level it will throw an error.please check for exit.
thanks,
surya -
Hi Experts,
Can anybody please help.New comer in QM.Please help.
How system calculate Quality score & quality level.What setting required for it. And where it is use. Please do not suggest sap library or F1 help.Please help.hi
Evaluation of Quality Levels
You can use this function to can select quality levels, display the selected quality levels in a list, reset or tighten selected quality levels, display the data and dynamic modification rules for selected quality level records, and display the dynamic modification history for quality levels as a graphic or in a list.
Quality levels that have been deleted can no longer be evaluated (that is, you can no longer obtain a dynamic modification history of the inspection lots that were included in these quality levels).
If the system finds more than one quality level record for the selection conditions, it switches to a dynamic selection list that contains all quality levels that meet the selection conditions.
If only one quality level exists for the selection criteria, the system switches directly to the dynamic modification history list for the corresponding quality level. The dynamic selection list appears by choosing Goto ® Back. You can make changes in this list. There are the following functions in the dynamic selection list:
In the transaction Edit list (menu path: Logistics --> Quality management --> Quality inspection -->Quality level -->Edit list)
Creating a Quality Level Manually
Use
In most cases, you will not need to create a quality level manually. However, if you are implementing the Quality Management (QM) application component for the first time, you may want to enter data for the quality levels recorded in your previous system.
Prerequisites
You can only create a quality level manually for lot-based dynamic modification.
Procedure
Choose Logistics -->Quality management --> Quality inspection --> Quality level --> Create.
Enter the necessary data on the initial screen for creating a quality level and choose Quality level.
You define the dynamic modification criteria (material, vendor, manufacturer, or customer) and the inspection plan for which the quality level will be maintained on the initial screen.
Enter the following data on the screen for creating quality levels:
Next inspection stage
Number of inspections or inspection lots that (based on the dynamic modification valuation) have been completed since the last inspection stage change or were accepted without an inspection (skip)
Number of inspections or inspection lots (based on the dynamic modification valuation) that were rejected since the last inspection stage change
Reset date on which the quality level again uses the initial inspection stage (specified in the dynamic modification rule) as the current inspection stage
Earliest possible deletion date for the quality level
The system makes entries in all other fields if:
An inspection lot is created.
A usage decision is made.
Save your data.
The initial screen for creating a quality level appears and the system informs you that the quality level was created.
-ashok -
how to do setting of quality score for vendor materials as per our requirements which are as under.
1 ) weightage of rejection at incoming stage
2 ) weightage of sorting at incoming stage
3 ) weightage of return from production
4 ) weightage of customer return due to vendor problem
5 ) weightage of material accepted under deviation
regards,
rakesh patelNot in SAP standard, so you need to develop some program.
I would suggest you discuss this requirement to your ABAPer.
1) 2) 5) Quaity score based on weighting of rejection, sorting, management deviation at incoming inspection.
- Develop a function module for calculation of quality score
(You should define how the system calculates the quality score.)
- Define new quality score procedure in configuration
(SPRO > Quality Management > Quality Inspection > Inspection Lot Completion > Define Quality Score Procedure)
- Assign new quality score procedure in inspection setup of material master QM view
3) 4) Which process in SAP do you have for "return from production or customer due to vendor problem".
If you have another inspection type, you can solve with above solution.
If not, let us know how SAP can get the information for calculation of quality score.
Regards
Luke -
QA32 UD - Disable screen fields UD code and Quality score in QA12 screen
Hi,
This is regarding the QM module , QA32 transaction , UD subscreen under Characteristics tab.
I need to disable the UD Code and Quality score screen field in QA12 in cases where the inspection lot stocks are completly posted.
How can I achieve this? Can some one plz suggest me the relevant User exit for this ?
Also how do i disable the screen field in QA12 ?
Regards,
P.S.ChitraHi,
Did u get any solution ???
Regards
Bharath -
Maintain Quality Score in QM Module
Dear Sir/Mam
As per standard sap Quality score is 1 or 100,i want to modified quality score into 50 , 60,80 as per my usage decision.
regards
kunalDear Kunal
You can do change quality score according to the usage decision
go to selected sets of usage decision. QS51.select the code group and go to codes
there you can define quality score against each code as per your need
Regards
gajesh -
Quality score and vendor evaluation?
Dear Sapient,
Can any one help me to know how quality score in QA11 or QA12 is hitting vendor evaluation programs?
Regards,
Kaushal RaiHi
Rejection/complaint : This comes from the Following calculation.
Only consider the Q2 type of notification score.
If no complaint then this is 100 otherwise following formula:
The complaints score is calculated from the number of complaints against the vendor, according to the following formula:
QSc = QScmin + (QScmax - QScmin) * (1 - (N * K) / (F * U))
QSc = QScmin if (N * K) > (F * U)
QScmin = Lower limit for QSc
QKZmax = Upper limit for QSc
N = Number of Q-notifications in the applicability period
K = Estimated nonconformity costs
F = Share of business volume for QSc calculation
U = Sales of the vendor in the applicability period
K is maintained at
QCC0>Quality notification->Information system--->Define NC cost for Vendor Evaluation
Audit:
The audit score is either the average quality score for the audits or is made up of the quality scores for the most recent audits. You can also enter an audit score manually.
This is 07 inspection type average score.
Again depend upon UD score of 07 inspection type.
I hope this will help
Regards
Sujit
Maybe you are looking for
-
No landline phone service for more than a week
I have been without landline phone service since Wednesday September 4th, 2013. Today, September 12, is a full 8 days without phone service. I have called Verizon countless amount of times with promises to come and fix my service but to no avail. I w
-
File to RFC (create Project Def in R# using data from XML file)
I configured the scenario as follows: Step 1. Created data type and message type suitable for file data. Createtd async outbound message interface Defined message mapping between Messge type defined and BAPI Defined Interface mapping between Message
-
How to extract the number of employees (Head count) in a particulr month
Hi Experts, We are trying to have a customized report on Having the employee headcount for a particular month with number of employees joined on the month and number of employees left the organisation.What is the way to get it. Please advice. V
-
Publish a business event through PL/SQL to SOA composite
Hi, My use case is this: I want to create/publish a business event from a PL/SQL procedure. I have a mediator component in a composite application to subscribe to that event. Has anyone tried this? Is it possible? I tried with edn_publish_event in so
-
Queries on tape drive configuration
Dear All, I have some queries on tape drive configuration We are on windows 2003 , oracle 10g and ecc6 . My requirements is to take backup on tape drive through brtools db13 Do that what need to be done at hardware and sap level means what tape devi