Why is my HP Deskjet 970C Print Queue Status "Stopped" and won't change?

I recently installed 10.5 Leopard. Hooked up my old HP-970C Deskjet. Used the link: http://www.linuxfoundation.org/en/OpenPrinting/MacOSX/foomatic to get the new HP Driver as recommended. Set up printer with this driver.
Each time the print command is given (Word Doc or .pdf file) nothing happens. The job is shown in the Print Queue with the Status says "Stopped." Clicking the resume button does not start the printer. Twice more and I get a message that says "Operation Could not be completed. client-error-not-possible."
Any thoughts on how to work around this?
Tried the six steps listed at: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01462601&lc=en&dlc=en&cc=us &lang=en&softwareitem=bi-54970-4&os=219&rule=5837&product=3435684
Even those great steps did not help. Any other ideas? Thanks!!!

The short answer is that you have an older HP printer, and have just been bitten by HP's abandonment of older printers on both Leopard and Vista.
The foomatic drivers should work, though; I used foomatic drivers on my old HP MFD for years. They gave better output than the ones HP shipped, and actually worked in Leopard. I put the HP onto a machine running XP because scanning didn't work anymore on either Vista or Leopard and HP had no intention of fixing it.
When I see the error you quoted, there are usually three possible causes:
1 the printer itself has a hardware problem. The fix for that is to buy a new printer, it's not economic to repair a DJ970.
2 the HP drivers are present on the system and are interfering. The fix for that is to remove the HP drivers and just have the foomatic drivers installed.
3 the USB cable is bad or loose. The fix for that is to get a new USB cable and make sure that it is securely plugged in.

Similar Messages

Why has my hp deskjet 2050 printer and scanner suddenly slowed down and printing one line at a time

why has my hp deskjet 2050 printer and scanner suddenly slowed down and printing one line at a time

This is usually indicative of a defective print cartridge. Suspect the black is low in ink or defective. Please check all cartridges.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Why does my printer say "offline" sometimes and won't print?

Why does my printer say "offline" sometimes and won't print?

Hi - Try following the steps in this document. It should help resolve the issue.
Hope that helps.
Say Thanks by clicking the Kudos thumbs up. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
I am an HP employee.

BW Queue Status Stopped: SXMB_MONI

Hi
I am passing data from XI to BW into a Data Source via Inbound Proxy. The problem is for some of my messages I get the status as Green Flag(Queue Status- Stop)in SXMB_MONI.
That means all those Messages are not posted to Data source even though they are successfully transferred from XI.
If I manually try to restart them. It says that the message are already scheduled in Queue. But in Queue there is no entry.
Should I regenerate my proxy? Even though out of 10 I still have 6 successful Messages and rest 4 as Queue status stopped.
Can anyone suggest what can be the problem?
Regards
Swetank

Hi,
is there any trasaction in BW where you can register your Queues. somthing like sxmb_Adm--> register Queues...
B'cos this was the same problem that i encountered when i was using another client(105) in XI-IS when executing server proxies. Then the queues in the client system were not registered.
so check if there is any place in BW system where you can register the queues.
cheers,
Siva maranani.

I have a Officejet 8500 A910n. When printing a pdf the print job just stops and will not print.

Only certain files the print job just stops and will not print in Adobe Acrobat X. All other applications work fine.

Have you tried downloading and installing Adobe Acrobat XI? http://www.adobe.com/products/reader.html
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Server Admin doesn't show Print Queue status

When I look at my print queues (all 17) under Server Admin, it shows queue name, # of jobs, shared via (IPP & SMB), and printer kind (HP LJ 1022n and HP LJ P2015). It has a column for status, but this is always 100% empty/blank. Also, if I go to the Jobs tab, then I can pick "Jobs on Queue" for all the queues, but the line below for "Queue Status" is again always blank.
Is there something I can do to get this info to show up in Server Admin? I know that CUPS knows the printer status, as I can go to localhost:631 and see the status in the Printers list and the Jobs list.
It isn't life threatening. It is just annoying to have to go to the web page when Server Admin -almost- gets me everything I need to diagnose a teacher's printing problem remotely.

Hi Keith
You could always consult the Print Service logs. If you set the logging levels to Debug or Debug2 you should get everything. You have to be a bit careful with this as the log can get quite large. Other than that I don’t know of anything that is available out of the box.
There may be others that can suggest a 3rd party solution that gives you the appropriate feedback you are looking for. Opening port 631 should not be that much of risk I would have thought?
Tony

Print Queue Status Monitor with Email

I have a brand new Windows Server 2012 R2 Datacenter virtual server that is setup as a print server. I saw the custom filters in the Print Management console but found out that notifications only work with that console open. Since I'm not logged
into that machine all the time, I need a powershell script that can do what the custom filters do in the Print Management console. Here's what I'm looking for:
1. When the print server starts the script starts. This script should always stay active.
2. The script polls the print queues for a change in status to anything other than Ready every 5 minutes or so.
3. If the printer name contains "CC2", then email certain people the status of that particular printer. Only email them once so as to not spam them with constant emails (maybe 1 email per day per status change).
So basically I'm looking to email my customer service department if one of their printers goes to a status of anything other than Ready. Is something like this possible with Powershell?

My scripts compares the customer service printers (printer names starting with CC2) status every 5 minutes. If the status has changed and there are Offline printers then customer service gets an email. I'm using Task Scheduler to start the script
at 6:00am every day and the script will quit around 11:00pm. It's not very elegant but it will get the job done. Thanks for all your help!
# Time limit when the script expires
$Limit = (Get-Date).AddDays(1)
$SleepSeconds = 300
$PreviousStatus = @()
while ((Get-Date) -lt $Limit)
$CurrentStatus = Get-Printer -computername SERVER | Where {($_.PrinterStatus -ne "Normal") -and ($_.Name -Match "CC2")} | Select Name,PrinterStatus
if ($CurrentStatus)
if (Compare-Object $CurrentStatus $PreviousStatus -property Name,PrinterStatus)
# Establish Connection to SMTP server
$a = "<style>"
$a = $a + "TABLE{border-width: 1px;border-style: solid;border-color: black;border-collapse: collapse;}"
$a = $a + "TH{border-width: 1px;padding: 0px;border-style: solid;border-color: black;}"
$a = $a + "TD{border-width: 1px;padding: 0px;border-style: solid;border-color: black;}"
$a = $a + "</style>"
$filedate = get-date
$smtpserver = “smtp.gmail.com”
$msg = new-object Net.Mail.MailMessage
$smtp = new-object Net.Mail.SmtpClient($smtpServer )
$smtp.EnableSsl = $True
$smtp.Credentials = New-Object System.Net.NetworkCredential(“[email protected]”, “password”); # Put username without the @GMAIL.com or – @gmail.com
$msg.IsBodyHtml = $True
$msg.From = “[email protected]”
$msg.To.Add(”[email protected]”)
$msg.To.Add(”[email protected]”)
$msg.To.Add(”[email protected]”)
$msg.To.Add(”[email protected]”)
$msg.To.Add("[email protected]")
$msg.Subject = "Printer Status Errors $($filedate)"
$msg.Body = Write-Output -InputObject (Get-Printer -computername SERVER | Where {($_.PrinterStatus -ne "Normal") -and ($_.Name -Match "CC2")} | Select Name,PrinterStatus,Comment,Location,Portname) | ConvertTo-Html -Head $a
$smtp.Send($msg)
$PreviousStatus = $CurrentStatus
Start-Sleep -Seconds $SleepSeconds
if ((get-date).Hour -eq 23) {Exit}

Print Queue suddenly stopped: OS X 10.4.10 and Bonjour via AirPort

I've been using an Intel iMac with no problems for many months: 2 printers attached: 1 inkjet via USB, and 1 HPLJ1200 via Bonjour through Airport/USB.
System Version: Mac OS X 10.4.10 (8R2218),
Kernel Version: Darwin 8.10.1
Suddenly, the Bonjour one has stopped. One minute it's printing, next minute, all jobs go into a queue but never emerge. The printer queue shows in the dock with a red "!" with all jobs in that queue stopped. If I restart the queue, it just tries to restart (green) then reverts to red "!" again. The direct USB printer continues to work fine. Problem is confined to the Bonjour printer.
I've tried:
1. Checking all the cables etc. Turning everything off, then one by one on. Restarting iMac, etc.
And then (after a few experiences of others on the Forums):
2. Verifying and fixing permissions via Disk Utility (there were no problems to fix)
3. Uninstalling the HPLJ, and then reinstalling.
4. Installing a 2nd instance of the HPLJ to bypass the first instance (which has a little grey "!" next to it in the Print dialogue box)
All to no avail.
I've then tried:
5. OnyX, running maintenance scripts, cleaning caches.
Still no good.
6. Finally, I've looked into the CUPS Error Log via OnyX, and I can see a number of Errors (see transcript at end of this email). I have removed the HPLJ from the printer setup, then reinstalled it. The CUPS Error Log for this is shown below, from removal, to reinstallation.
Is there a Unix or OSX expert in the forum who can help please?
Many thanks
LeslieB
=================
(extract of newest lines of CUPS Error Log, from OnyX:
Covers process of deleting, then readding HPLJ1200, to the USB port on Apple Airport. Printer was recognised as Bonjour and installed. Sharing was enabled. Then test page was printed ->failed to print and queue showed red "!")
E [14/Aug/2007:21:52:15 +1000] getprinterattrs: resource name '/printers/®¯6' no good!
E [14/Aug/2007:21:52:15 +1000] getprinterattrs: resource name '/printers/Pâ¨ê' no good!
I [14/Aug/2007:21:52:28 +1000] Printer 'HPLaserJet1200' deleted by ''.
I [14/Aug/2007:21:52:28 +1000] Saving printers.conf...
E [14/Aug/2007:21:52:28 +1000] getprinterattrs: resource name '/printers/HPLaserJet1200' no good!
I [14/Aug/2007:21:55:53 +1000] Setting HPLaserJet1200 device-uri to "mdns://HP%20LaserJet%201200.pdl-datastream.tcp.local./?bidi" (was "file:/dev/null".)
I [14/Aug/2007:21:55:53 +1000] Setting HPLaserJet1200 printer-is-accepting-jobs to 1 (was 0.)
I [14/Aug/2007:21:55:53 +1000] Setting HPLaserJet1200 printer-state to 3 (was 5.)
I [14/Aug/2007:21:55:53 +1000] Saving printers.conf...
I [14/Aug/2007:21:55:53 +1000] New printer 'HPLaserJet1200' added by ''.
I [14/Aug/2007:21:56:02 +1000] Installing config file "/private/etc/cups/cupsd.conf"...
I [14/Aug/2007:21:56:02 +1000] Listening to 0:631
I [14/Aug/2007:21:56:02 +1000] Listening to c0173200:0
I [14/Aug/2007:21:56:02 +1000] Loaded configuration file "/private/etc/cups/cupsd.conf"
I [14/Aug/2007:21:56:02 +1000] Configured for up to 100 clients.
I [14/Aug/2007:21:56:02 +1000] Allowing up to 100 client connections per host.
I [14/Aug/2007:21:56:02 +1000] Partial reload complete.
I [14/Aug/2007:21:58:30 +1000] Adding start banner page "none" to job 5.
I [14/Aug/2007:21:58:30 +1000] Adding end banner page "none" to job 5.
I [14/Aug/2007:21:58:30 +1000] Job 5 queued on 'HPLaserJet1200' by 'leslie'.
I [14/Aug/2007:21:58:30 +1000] Started filter /usr/libexec/cups/filter/cgpdftops (PID 1474) for job 5.
I [14/Aug/2007:21:58:30 +1000] Started filter /usr/libexec/cups/filter/pstops (PID 1475) for job 5.
I [14/Aug/2007:21:58:30 +1000] Started filter /Library/Printers/hp/filter/hppostprocessing (PID 1476) for job 5.
I [14/Aug/2007:21:58:30 +1000] Started backend /usr/libexec/cups/backend/mdns (PID 1477) for job 5.
E [14/Aug/2007:21:58:32 +1000] [Job 5] Unable to locate printer 'Leslie-Office.local.' - Unknown host
E [14/Aug/2007:21:58:32 +1000] PID 1477 stopped with status 1!
I [14/Aug/2007:21:58:32 +1000] Hint: Try setting the LogLevel to "debug" to find out more.
I [14/Aug/2007:21:58:32 +1000] Saving printers.conf...
I [14/Aug/2007:21:58:41 +1000] Saving printers.conf...
I [14/Aug/2007:21:58:41 +1000] Printer 'HPLaserJet1200' started by ''.
I [14/Aug/2007:21:58:41 +1000] Started filter /usr/libexec/cups/filter/cgpdftops (PID 1490) for job 5.
I [14/Aug/2007:21:58:41 +1000] Started filter /usr/libexec/cups/filter/pstops (PID 1491) for job 5.
I [14/Aug/2007:21:58:41 +1000] Started filter /Library/Printers/hp/filter/hppostprocessing (PID 1492) for job 5.
I [14/Aug/2007:21:58:41 +1000] Started backend /usr/libexec/cups/backend/mdns (PID 1493) for job 5.
E [14/Aug/2007:21:58:43 +1000] [Job 5] Unable to locate printer 'Leslie-Office.local.' - Unknown host
E [14/Aug/2007:21:58:43 +1000] PID 1493 stopped with status 1!
I [14/Aug/2007:21:58:43 +1000] Hint: Try setting the LogLevel to "debug" to find out more.
I [14/Aug/2007:21:58:44 +1000] Saving printers.conf...
And while I was typing this forum posting, and doing a further test print, then cancelling it when I could not start the queue, the following error log was appended:
I [14/Aug/2007:22:06:07 +1000] Started filter /usr/libexec/cups/filter/pstops (PID 1650) for job 5.
I [14/Aug/2007:22:06:07 +1000] Started filter /Library/Printers/hp/filter/hppostprocessing (PID 1651) for job 5.
I [14/Aug/2007:22:06:07 +1000] Started backend /usr/libexec/cups/backend/mdns (PID 1652) for job 5.
E [14/Aug/2007:22:06:09 +1000] [Job 5] Unable to locate printer 'Leslie-Office.local.' - Unknown host
E [14/Aug/2007:22:06:09 +1000] PID 1652 stopped with status 1!
I [14/Aug/2007:22:06:09 +1000] Hint: Try setting the LogLevel to "debug" to find out more.
I [14/Aug/2007:22:06:09 +1000] Saving printers.conf...
I [14/Aug/2007:22:15:32 +1000] Job 5 was cancelled by 'leslie'.
I [14/Aug/2007:22:15:40 +1000] Saving printers.conf...
I [14/Aug/2007:22:15:40 +1000] Printer 'HPLaserJet1200' started by ''.

Dear All
I have been able to partially solve this problem myself.
I've managed to track the problem down to the Apple Airport Express (which is hosting the USB printer via Bonjour). The problem seems to be that the iMac can't see the printer, even thought it's connected.
It turns out that the problem started at the time of an internet outage, and the iMac can't seem to find the printer since that time (even though Bonjour is working fine).
I've tried resetting the Airport Express, and even upgrading the firmware, but no luck so far.
I'll close this posting, and put a new one in the Airport Express Forum.
many thanks to those who viewed this in the interim.
LeslieB

Print Queue Auto Stop

Just though I'd share this with others.
Unlike Tiger, the printer queues would not quit automatically on Leopard after a job is finished. The solution was simple.
If no queue is running, go to System Preferences > Print & Fax. Click on ANY installed printer then click on the 'Open Print Queue' button.
Now navigate to the Dock, control-click (or Right Click) on the running Printer Queue. In the pop up menu is "Auto Quit" (right above "Keep In Dock"), click on it so it is check marked. Now ANY Printer Queue will quit when the job(s) are finished. Making just one Printer Queue "Auto Quit" sets it for all installed printers!
Seems I've been fortunate and have had no problems with my 5 printers transitioning to Leopard, so I hope this tip is helpful to others.
Cheers

Thanks for this info. Just what I need. Not intuitive at all. Jim

Print to PDF Causes print Queue to stop

My user has been having a lot of difficulties with Acrobat 11 (For Windows 7). When she tries to use the Adobe PDF printer and print to PDF, occasionally it will lock up the print queue and will not complete. It also will not release the prints. I have to run a repair on Adobe as restarting the spool service or going into the spool folder and trying to delete the items does not work.
I have run the repair several times and most recently totally uninstalled and re installed Acrobat, made sure all updates were applied but each time it temporarily fixes the issue for a few days and ends up coming back. Any ideas of what I can do next?

Yes, this is caused by the HP 2.10 update.
Among other threads: https://discussions.apple.com/thread/4197112?tstart=0
Remove /Library/Printers/hp/PDEs/hpPostScriptPDE.plugin.
Hope this helps.

Printer queue keeps stopping

I’m trying to print to Adobe Acrobat (the only working “printer” I have right now) The PDF file does not appear in the chosen destination.
So I go to print Center. In the Printer list window, though it says “Printing,” I see the message:
“Printing of jobs for this printer is stopped. Do you want to continue and restart the printing of jobs? If you select continue and the printing of jobs cannot be restarted, this job will automatically be added to the queue.”
I choose “Restart.” In the Printer window it shows the progress bar.
Finally, after a long time processing, it says at the top of the Printer window, “Jobs Stopped.” (?) The file is added to the bottom of the list in the Printer window (by now a fairly long list). No file appears in the specified location.
If I click the “Start Jobs” icon, it goes through the same rigamarole and still no files appear, and again it says “Jobs Stopped.” The files remain in the list of files still to be printed.
I can create a PDF through the Mac’s “Save as PDF"button at the bottom of the print dialog, but not through Acrobat.

I don't have an answer, but I do have exactly the same problem! I was previously able to print wireless from my laptop PC and from my desktop PC to the printer connected to USB port of the AEBS. Now, I can print only if I connect the printer directly to one of the PC's with the USB cable.
I spent quite a bit of time on the phone with Apple technical support. We tried rebooting the AEBS, and well as Restarting it from the menu.
I was able to print if I set up the printer via a shared connection to my MacBook Pro with the printer connected by Ethernet cable, but that is not an acceptable solution, since it means that the MacBook Pro has to be turned on in order to print from the PC.
I have even exchanged the AEBS for a new one at the Apple store, but I am still not able to resolve this issue.
Apple Technical Support ended the conversation by saying they do not provide support for Bonjour printing problems on a PC.
This must be a software problem, because I have been able to get this functionality to work for my customers who have AEBS's in a mixed computer environment.
MBP 15" 2.16GHz, 2GB RAM Mac OS X (10.4.9) AEBS Firmware v7.1, HP Laserjet 2605dn printer

Printer Utility says Stopped and failed even though it works other times

I have the Photosmart C4599. All I did was get a new wireless router. I hooked it up and the printer sees it fine. I did the wireless test and it worked fine. I am on a Mac and the print and Fax under system prefrences sees it fine.
When I try and print from Word or PDF or whatever it acts like it about to print but in the utility it just says the job is stopped. When I try to resume it doesn't do anything and won't ever print. After clicking around many times I got it to say it failed. I have updated and reinstalled all drivers and set up. It knows it's there but just won't print.
Any suggestions? Thanks in advance

Delete and re-add the printer in the print queue:
- Sys Prefs, Print & Fax
- Select the printer in question and click the minus sign at the bottom of the list
- Select the plus sign to re-add it. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
If this does not work, do the same thing, only instead of the second step, right (control) click the print queue area and select Reset Printing System.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Help! One error printing and now all print jobs status = STOPPED.

I work in a big corporation with 99.99% PCs. I've been printing to networked printers here under Leopard without problem for a long time now. I recently submitted a print job to a HP printer and all it printed was:
Error: invalidfont
OFFENDING COMMAND: definefont
STACK:
-dictionary-
/HSRYIE+ArialNarrow-Italic
However, since that moment I have been unable to print anything irrespective of what printer I choose (HP, Xerox etc). Every time I start a job it immediately shows with a status of STOPPED in the printer window. Other people continue printing to these printers just fine, snickering at my Mac along the way .
Any ideas??

Hoping to inspire some tech-head to respond here...
Restarting doesn't fix this. Repairing permissions doesn't fix this. Removing and reinstalling the printer doesn't fix this.
When I create a print job I get the following in the error_log:
I [30/Jan/2008:07:53:10 -0700] [Job 63] Adding start banner page "none".
I [30/Jan/2008:07:53:10 -0700] [Job 63] Adding job file of type application/pdf.
I [30/Jan/2008:07:53:10 -0700] [Job 63] Queued on "146_252_6468" by "mmueck".
I [30/Jan/2008:07:53:10 -0700] [Job 63] Started filter /usr/libexec/cups/filter/cgpdftops (PID 5036)
I [30/Jan/2008:07:53:10 -0700] [Job 63] Started filter /usr/libexec/cups/filter/pstops (PID 5037)
I [30/Jan/2008:07:53:10 -0700] [Job 63] Started filter /Library/Printers/hp/filter/hpPostProcessing.bundle/Contents/MacOS/hpPostProces sing (PID 5038)
I [30/Jan/2008:07:53:10 -0700] [Job 63] Started backend /usr/libexec/cups/backend/lpd (PID 5039)
E [30/Jan/2008:07:53:10 -0700] [Job 63] `/private/var/spool/cups/d00063-001' has permissions that do not allow printing!
E [30/Jan/2008:07:53:10 -0700] PID 5036 (/usr/libexec/cups/filter/cgpdftops) stopped with status 1!
I [30/Jan/2008:07:53:10 -0700] Hint: Try setting the LogLevel to "debug" to find out more.
E [30/Jan/2008:07:53:10 -0700] [Job 63] Empty print file!
E [30/Jan/2008:07:53:10 -0700] PID 5037 (/usr/libexec/cups/filter/pstops) stopped with status 1!
I [30/Jan/2008:07:53:10 -0700] Hint: Try setting the LogLevel to "debug" to find out more.
E [30/Jan/2008:07:53:10 -0700] [Job 63] Job stopped due to filter errors.
I homed in on the spooled file permissions issue and (as root) changed the permissions of that file to 777 and re-submitted the job, yielding the following log:
I [30/Jan/2008:07:56:26 -0700] [Job 63] Started filter /usr/libexec/cups/filter/cgpdftops (PID 5058)
I [30/Jan/2008:07:56:26 -0700] [Job 63] Started filter /usr/libexec/cups/filter/pstops (PID 5059)
I [30/Jan/2008:07:56:26 -0700] [Job 63] Started filter /Library/Printers/hp/filter/hpPostProcessing.bundle/Contents/MacOS/hpPostProces sing (PID 5060)
I [30/Jan/2008:07:56:26 -0700] [Job 63] Started backend /usr/libexec/cups/backend/lpd (PID 5061)
I [30/Jan/2008:07:56:26 -0700] [Job 63] Restarted by "mmueck".
E [30/Jan/2008:07:56:26 -0700] [Job 63] `/private/var/spool/cups/d00063-001' has permissions that do not allow printing!
E [30/Jan/2008:07:56:26 -0700] PID 5059 (/usr/libexec/cups/filter/pstops) stopped with status 1!
I [30/Jan/2008:07:56:26 -0700] Hint: Try setting the LogLevel to "debug" to find out more.
E [30/Jan/2008:07:56:26 -0700] PID 5058 (/usr/libexec/cups/filter/cgpdftops) stopped with status 1!
I [30/Jan/2008:07:56:26 -0700] Hint: Try setting the LogLevel to "debug" to find out more.
E [30/Jan/2008:07:56:26 -0700] [Job 63] Empty print file!
E [30/Jan/2008:07:56:26 -0700] [Job 63] Job stopped due to filter errors.
If anybody can even offer a clue to what happened here I'd be very appreciative.
Mick.

Queue status stopped

Hi All,
I am trying a file to file scenario. In SXMB_MONI the message status is "scheduled" and the queue status is "stopped".
I have tried deregistering and registering the queue.
i also tired to see the error in by double clicking on the queue ID it shows SYSFAIL. when i double click on SYSFAIL it shows a message "XI ERROR Update XI Cache Queue Stopped". for this i have also refreshed the cache. but nothing seems to help.
Anyone having a clue?
Thanx in advance.
Latika.

Hi Latika,
Reason,
http://help.sap.com/saphelp_nw04/helpdata/en/49/e3fb40ef74f823e10000000a155106/content.htm
1. Try restarting J2EE stack.
2. One of the reason may be database overflow. In this case also, restart is required.
3. Check if XIAPPLUSER & XIAFUSER are locked. Also retype the password and try.
Check out Steve Winkler's response here
To Be Delivered on Adapter Message for JDBC
Regards,
Prateek

Epson 2200 Printer disappeared from list and won't come back

My Epson 2200 printer has disappeared from my printer list, and I cannot find it again in the Firewire list. I have reinstalled the latest printer driver, I have tested plugging in someone else's Epson 2200 - and it shows up no problem. My printer won't even turn on when it is connected to my mac. Why would this happen all of a sudden?
iMac g5 power pc Mac OS X (10.4.9)

Welcome to Discussions - Have you tried plugging your printer into another computer? It sounds as if the printer has problems. Have you tried unplugging it, then restarting and plugging it in? Does the USB port work with other peripherals? Try posting to the Epson SUPPORT page and see if anyone there has had the same experience.
Let us know how you make out,
Miriam

Why is my HP Deskjet 970C Print Queue Status "Stopped" and won't change?

Similar Messages

Maybe you are looking for